TOPIC-LIGHT Celeb 2 Manual de usuario

User Manual

Please read this manual carefully before using the product

Laser show projector Celeb 2/3

Introduction

Thank you for purchasing this product.We always try to develop our

product with high-tech and high performance to meet your

requirement and exception.

The unit is designed strictly according to the international standard.

The control way is single or master-slave in option. The manual

include the skill parameter and detail instructions. Please read this

manual carefully before using the product.

After reading it, please keep it in a safe place for future reference.

This unit has been tested at our factory before being shipped to

you, there is no assembly required.

Once after receiving this product, please take and put carefully.

And check cautiously that whether the product was damaged or not

during the transportation.

Checking parts

Please check if the following parts are included:

1 x Laser

1 x User manual

1 x Power cable

1 x Hanger

Danger Laser Radiation!

Avoid direct eye exposure!

Laser radiation can cause eye damage or skin damage

All protective measures for a safe operation of this laser

must be applied.

Installation

1. Please check the voltage whether is the same with the one

showed on the equipment or not.

2. It must ask for the technical person and set the light safety when

installation. And let the light beam at the suitable angle.

3. When install this equipment please make sure there's no

flammable surfaces (decorated things, etc) within at least 2.5M and

maintain minimum distance of 0.5M from the equipment to the walls.

4. Please make sure that there's no other equipment or decorating

materials obstructed the exhaust fan and the vent-pipe.

5. Products should be install immobility.

6. In case of safety, it's very important that to connect the earth with

line.

Attention

1. Please do not open the bottom cover yourself without permission.

Operate it accord the user manual. Call the technician when the

machine breaks down.

2. Please do not see the laser beam directly to avoid any damage.

3. Before connect or disconnect the power, please adjust the

luminance of the laser diode to the least to avoid any damage to the

laser diode.

4. This unit should be keep dry, do not use in the rain and dusty

environment. It can be use in the outdoor with the water-proof cover

protector.

5. Set the light immobility and try to avoid strong shake or hit.

6. Prevent dust into the equipment to avoid problems.

7. Please keep that there's no other equipment or decorating

materials obstructed the exhaust fan and the vent-pipe when the

equipment was working.

8. Before connect power, check the plug is immobility or not, power

line should be connect well.

9. Please do not open or close the equipment frequently that's to

avoid any affect to the life span of the laser diode, and try the best to

avoid the long time working.

10. Due to the characteristic of the laser diode, after four hours

working, it should be close at least 25 minutes until the laser diode

cooling then work again.

11. Don't touch the light or draw the power line when your hand was

wet. And do not pull the electronic power line.

12. Maintain the distance at least 3M above from the equipment to

the object.

13. This equipment does not have any parts can repair for the users,

please do not open the equipment.

14. When the laser diode became dim or damaged please contact

the dealer timely.

15. When you want to re-transfer the product, you'd better use the

original package to shockproof.

LCD display function menu

Menu Secondary menu

Operation Mode

DMX-512

Auto TRG

Music TRG

Test Mode

DMX address 1~512

Auto Trigger 1~25

Music Trigger 1~25

Test Mode Enable Laser

Test Pattern1~4

Master settings

Master Size 0~255

X Scale 0~255

Y Scale 0~255

Invert X

Invert Y

Color settings

Color Shift RGB/I

Fade 0~255

Red 0~255

Green 0~255

Blue 0~255

System Config Master/slave

Channel 27CH/52CH

Sound sense

Scan-safety

Easy ILDA

System Reset

Device Info

DMXADDR

T case

Swflash LF001

Hdw 5006.2.0

Ver A1.1

1. DMX setting：

Input DMX signal, and the link the DMX controller and the lights by the control

line as the following picture, you can control the lights by the controller.

When using any controller, each one must be have its own address. The fist

light address is set to 1, the second light address code is set to 28 or 53 (the first

light address code 1 plus 27 or 52 channel), the third set of lights on the 55 or

105. (This setting also need to be based on different console to set, now only by

general practice)

Fixture No. Address LCD display（No.）

1 1 1

2 28 or 53 028 or 053

3 55 or 105 055 or 105

┇ ┇ ┇

2. Master-slave Setting：

Link the lights as the following picture (the light which does not receive signal,

only output signal, will be the master light)

Using before please must be check power supply link with earth wire

correctly or not.

The specification of the front and rear panel:

1. Input rated voltage

2. Fuse

3. Power switch button

4. Ground marking

5. DMX IN/ DMX OUT: DMX signal output and input

Technical Specifications

Power input: AC100~240V, 50/60Hz

Power consumption: 100W, 200W

Laser: Single color RGB

Laser modulation: TTL Analog

Scanner: 20kpps 25kpps 30kpps

Channel: 27CH / 52CH

Control mode: sound, auto, master-slave, dmx, ilda

Cool system: forced air cooling system

Working temperature: 0℃- 35℃

N.W./G.W.: 10kg/12kg (1pc)

Package size: 60 x 35 x 28cm

DMX-512 Channel Introduction：

27CH:

Channel Value Parameter description

CH1 IPLAY mode

0～31 Black

32～63 Manual play

64～95 Auto play

96～128 Music play

129～255 Invalid

CH2 Dimmer 0～255 Fade 0% - 100%

CH3 Red 0～255 Fade 0% - 100%

CH4 Green 0～255 Fade 0% - 100%

CH5 Blue 0～255 Fade 0% - 100%

CH6

Page

0～255

Each 32 value be 1 page, total 8 pages（valid

for CH1=32～63）

Macro

Each 10 value be 1 macro, total 25 macros

（valid for CH1=64～128）

CH7 Cue

0～15 Black

16～255

CH1(32～63) each 12 value be 1 cue，total

20 cues

CH8 X position 0～255 Left - right movement（128 center）

CH9 X fine 0～255 X position fine movement

CH10 Y position 0～255 top - bottom movement（128 center）

CH11 Y fine 0～255 Y position fine movement

CH12 Rotation 0～255 CW rotation (0°-360°)

CH13 Fine 0～255 Fine rotation

CH14 Zoom 0～255 100% - 0%

CH15 X flip 0～255 Flip from left to right

CH16 Y flip 0～255 Flip from top to bottom

CH17 Color

0～7 Default

8～15 White

16～23 Red

24～31 Yellow

32～39 Green

40～47 Cyan

48～55 Blue

56～63 Purple

64～127 Each 8 value be 1 color, total 8 colors

128～255 Each 16 value be 1 macro, total 8 macros

CH18 Write in 0～255 Visible point 100%-0%

CH19 Deformation

0～15 Invalid

16~223

Each 16 value be one macro function（valid

for 14CH 25CH）

224～255 Default

CH20 Wave 0 Invalid

1～39 Each 40 value be 1 macro, total 6 macros

CH21 Write in

0 Invalid

1～42 Macro 1

43～84 Macro 2

85～126 Macro 3

Strobe 127～255 Strobe （slow to fast）

CH22 X position 0 Invalid