TOP VEHICLE TECH GRKFD04 Manual de usuario
www.topvehicletech.com
The informaon provided in this document is subject to change without noce due to changes and/or
improvements to the product/s.
V2.0522
GRKFD04
FORD TRANSIT
2015-2021
INSTALLATION MANUAL
This dash image is a visual representaon for display purposes only.
2
www.topvehicletech.com
ABOUT THIS PRODUCT
The GRKFD04 installaon kit allows for the retenon of the vehicle’s steering wheel controls and helps maintain
the original aesthec of the interior when installing a new car stereo. The GRKFD04 gives you everything you
need for a complete install in one box. The components of this kit are compable for the Ford Transit (V363,
2015-2021) with factory stereos. The wiring harness and interface will retain the steering wheel controls, factory
phone buons and parking sensor audio (if vehicle is equipped). The interface supplied features a Ford OEM
specic connector.
Installaons should be carried out by, or under the guidance of an experienced installer. If you do encounter any
problems during the installaon of this product, then please contact our dedicated customer service team at:
Phone: E-Mail:
• 1x Fascia plate (with accessories)
• 1x Instrucon manual
• 1x Steering wheel control harness and interface
• 1x Antenna adapter
• 1x Stereo patch lead
3
www.topvehicletech.com
1. Use a panel removal tool to lever o the top dash cover which is held in place by x12 locator clips.
1. Once the main fascia panel is o, remove both torx screws that hold the air vents in place. These will
then need to be relocated onto the new fascia. Use 2x of the screws within the kit to aach the fans to the
new fascia.
2. Take either the newly ordered or pre-exisng hazard & airbag light and insert them into the fascia in the
applicable port. If the vehicle does not have a airbag light, we have included a blanking plate in the kit.
2. Remove the 2x torx screws found at the top of the main fascia, and using a panel removal tool, pry away
the enre panel, disconnecng the hazard switch connector in the process.
3. Remove the 2x screws that hold the main radio in place and remove it from the dashboard, again,
disconnecng all the wiring in the process.
Some plascs will need to be cut and removed from the dashboard to make space for the new car stereo.
Measure where the stereo will sit and take due care when modifying the vehicle. TopVehicleTech always promote the
help of professional installers. TopVehicleTech will not be held responsible for any damage to the vehicle.
3. Aach the 12x metal clips within the kit onto the new dash panel. These clips have a specic locaon as
shown below:
4
www.topvehicletech.com
4. When all the above wires (and any addional accessories) have been connected, nally make the power
connecons between the stereo and the vehicles pre-exisng connector.
1. Take the steering wheel control interface and aach the 14-way steering wheel harness connector to
the relevant side.
3. Aach the antenna adapter to the vehicles pre-exisng connecon and the back of new stereo.
5. Aach the brackets to either side of the radio using the 4x screws within the kit. Once aached, roughly
test t the radio and bracket combinaon in relaon to the new fascia, doing this, you can best measure
whether the brackets need moving forwards/backwards.
6. Aer the “Stereo Installaon” process is complete and you are re-assembling the vehicle, simply place
the new fascia over top the radio and ulising the plasc clips, secure it rmly to the dashboard.
4. Once all of the metal clips have been seen to, proceed to aach the remaining 4x plasc clips to long
locator posts on the back of the new fascia.
CONT’D
2. Make a cut within the orange and purple loops on the back of the patch lead connector. Then proceed
to aach ‘Key 1’ to the light blue ‘SWC Remote’ wire on the stereo. When done, connect the 12-way
connector to the steering wheel control interface.
5
www.topvehicletech.com
Please note: conguraon layout may dier dependent on vehicle model.
1
2
3
4
1. Volume +
2. Volume -
3. Track -
4. Track +
1. Volume +
2. Volume -
3. Track -
4. Track +
6
www.topvehicletech.com
ISO Connector
Connect to new stereo
Vehicle Specific Connector [OEM Specific]
Connect to OEM connector from vehicle
Main Wiring Loom Connector [14 Pin]
Connect to Interface Box
Interface Box
Stereo Connection (Patch)
Lead Connector [12 Pin]
Connect to Interface Box
Note: Must be connected
first, before power
connection is made to the
interface
7
www.topvehicletech.com
8
www.topvehicletech.com
If at any point you experience any problems and need any assistance before, during or aer the
installaon process, please contact us via :
Phone:
E-Mail:
Mon - Fri 9am - 5.30pm GMT
If you would like to download a digital copy of this manual, or any other product, then please
visit the www.topvehicletech.com website.
This manual is considered correct at the me of prinng but is subject to change. For the latest
manuals & updates, refer to our website.
Copyright 2022 by TopVehicleTech.
All rights reserved. No part of this publicaon may be reproduced, distributed or transmied
in any form or by any means, including photocopying, recording, copying or other electronic or
mechanical methods, without the prior wrien permission of the author.
Tabla de contenidos
Otros manuales de Sistema de vídeo para coche de TOP VEHICLE TECH
TOP VEHICLE TECH
TOP VEHICLE TECH KWPOR7 Manual de usuario
TOP VEHICLE TECH
TOP VEHICLE TECH GR3VXL4 Manual de usuario
TOP VEHICLE TECH
TOP VEHICLE TECH KWPOR16 Manual de usuario
TOP VEHICLE TECH
TOP VEHICLE TECH GRKBM02 Manual de usuario
TOP VEHICLE TECH
TOP VEHICLE TECH KWPOR12 Manual de usuario
TOP VEHICLE TECH
TOP VEHICLE TECH GRKLR05 Manual de usuario
TOP VEHICLE TECH
TOP VEHICLE TECH KWBMW15 Manual de usuario
TOP VEHICLE TECH
TOP VEHICLE TECH KWBMW11 Manual de usuario
TOP VEHICLE TECH
TOP VEHICLE TECH KWBMW3 Manual de usuario
TOP VEHICLE TECH
TOP VEHICLE TECH KWBMW9 Manual de usuario
