Top RC Model F9F Cougar Manual de usuario

Otros manuales de Juguete de Top RC Model

Top RC Model

Top RC Model Beechcraft Bonanza V35 Manual de usuario

Top RC Model

Top RC Model Super galeb G-4 ARF Manual de usuario

Top RC Model

Top RC Model Focke-Wulf Fw190A-8 Manual de usuario

Top RC Model

Top RC Model P-51D Mustang 89 inch Manual de usuario

Top RC Model

Top RC Model Sport Jet Aspire ARF Manual de usuario

Top RC Model

Top RC Model Hurricane MKIIB Instrucciones de montaje

Top RC Model

Top RC Model F-16 Fighting Falcon Manual de usuario

Top RC Model

Top RC Model P-51D Mustang 89 inch Manual de usuario

Top RC Model

Top RC Model Sport Jet Odyssey Manual de usuario

Manuales populares de Juguete de otras marcas

marklin

marklin 37321 Manual de usuario

Canon

Canon PAPER CRAFT Manual de usuario

GREAT PLANES

GREAT PLANES Pitts M-12S Manual de usuario

NOCH

NOCH 14261 Manual de usuario

Hausler

Hausler 450 SE V2 Manual de usuario

Dynaflite

Dynaflite Daydream Manual de usuario

MiniacRC

MiniacRC MIGHTY MINI P40 WARHAWK Manual

Kenner

Kenner Batman 63651 Manual de usuario

LEGO

LEGO 8527 Manual de usuario

iKarus

iKarus ECO 8 Manual de usuario

Multiplex

Multiplex EasyStar II Manual de instrucciones

Walkera

Walkera 38 Manual de instrucciones

Hasbro

Hasbro TRANSFORMERS BUMBLEBEE Manual de usuario

MD

MD MXION SWD Manual de usuario

Mattel

Mattel Disney Pixar Cars Cozy Cone Spiral Rampway Manual de usuario

marklin

marklin 39671 Manual de usuario

Meccano

Meccano 15103 Manual de usuario

LEGO

LEGO TECHNIC 8735 Manual de usuario

第 1 页，共 17 页

第 2 页，共 17 页

第 3 页，共 17 页

Accessory part lists for wing installation. 3. Epoxy the wood block to the servo tray base on the

mark line.

1. Ready for assemble the wing servos.

4. Epoxy the wood block to the servo tray tightly.

2. Put the wood block to appropriate position base on the

servo tray, mark out with red.

5. Assemble the servo to the servo tray with screws.

第 4 页，共 17 页

6. Assemble the servo to the wing 9. Before glue the arm to the slot, put masking tape

around the slot to keep clean.

7. Drag the servo line out of the wing.

10. Glue the arm to the slot and wait it dry.

8. Prepare to assemble the push rod arm.

11.Connect the arm of the flap and servo arm with push

rod.

第 5 页，共 17 页

12.The scketch map of the servo for the wing assembly

finished. 14.Prepare the parts for assembly the stab servo.

Accessories part list for the stabilizer installation.

15.Measure the deepth and mark out where the servo

would location.

13.Sanding the fiber horn.

16.Trim a lot for the stab servo arm.

第 6 页，共 17 页

17.Glue the horn to the elevator and assemble the servo to

the stabilizer. 19.Apply instand type AB glue to the slots in the rudder.

18.Connect the arm of servo to the horn with push rod.

20.Apply instand type AB glue to the slots in vertical fin.

Accessories part lists for the rudder installation.

21.Assemble the rudder to the vertical fin and make sure

it can move freely.

第 7 页，共 17 页

22.Apply instand type AB glue to the slots in the tail cone. 25.Mark it out at the outer side of the vertical.

23.Assemble the tail cone to the vertical fine tightly.

26.Trim a slot for the servo arm.

24.Measure the deepth of the rudder servo position.

27.Assemble the servo into the vertical fin with screw

driver.

第 8 页，共 17 页

28.The sketch map after the servo of rudder assembly. 31.Glue the fiber horn to the slot tightly.

29. Trim a slot at the appropriate position in the rudder.

32.Remove the masking tape after the glue dried.

30.Put masking tape around the slot to keep the plane body

clean after work done.

33.Connect the servo arm to the rudder fiber horn .

第 9 页，共 17 页

Accessory part lists for retract installation(Optional and

need purchased separately).

36.The sketch map after the main retracts assembled

completely.

34.The sketch map of the electric retract system (Optional

and need purchased separately)

37.The sketch map of the nose gear and nose gear servo

parts.

35.Assemble the retract to the fuselage with screws.

38.Assemble the nose servo to the nose gear.

第 10 页，共 17 页