ToolKitRC M7AC Manual de usuario

@ToolkiRC 2022

M7AC

Manual V1.0

2022.08

www.toolkitrc.com

ToolkitRC Technology (Shenzhen) Co., Ltd

@ToolkiRC 2022

Introduction

Thank you for purchasing the M7AC balance

charger, please read this manual carefully before use.

Key Points

Tips

Important

Information

Further information

To ensure you have the best experience with this

product, please scan the QR code below to stay up to

date with news, information and firmware updates for

your charger; this information could be found at

www.toolkitrc.com

@ToolkiRC 2022

Safety

1. allows input voltage of DC 7-28V or AC 100-240V.

Ensure the charger is only connected to a suitable power

source and correct polarity.

2. Do not use this product in hot, humid, flammable or

explosive environments.

3. Please do not use this charger without supervision.

Never leave charging batteries unattended.

4. When not using this product, please unplug the input

power.

5. When using the charging function, please set a

current that matches the battery. Do not set an excessive

current for charging to avoid damage to the battery.

Check the guidelines of your battery’s manufacturer for

correct charging instructions.

@ToolkiRC 2022

Contents

Introduction......................................................... 2

Key Points.............................................................2

Further information............................................ 2

Safety.....................................................................3

Contents............................................................... 4

M7AC Layout....................................................... 7

Quick start............................................................ 8

Charge and discharge settings.........................9

1. Battery type setting.........................................9

2. Cell Setting.....................................................12

3. Work Mode....................................................13

4. Discharge mode........................................... 14

5. Max input voltage.........................................15

6. End voltage setting (TVC)........................... 16

7. Current setting.............................................. 17

@ToolkiRC 2022

8. NiMH setting (PeakV)...................................18

9. Cycle setting.................................................. 19

10. External load setting................................... 21

11. Smart battery setting...................................22

Charge and discharge work............................24

Accessibility........................................................ 28

3. Signal output................................................. 31

4. ESC test.......................................................... 35

5. Power..............................................................35

System settings..................................................37

Customize function...........................................41

1， Boot image................................................. 41

2. Broadcast voice.............................................43

Other functions................................................. 44

Specifications..................................................... 46

@ToolkiRC 2022

Product description

The M7AC is a multifunctional tool that integrates

functions such as a balance charger and discharge, a

signal measuring device, and a signal source.

Support AC100W or DC300W dual input。

Charges, discharges and balances (where

applicable) LiPo, LiHV, LiFe, Lion, LTO 1-6S, NiMh

1-16S, PB 1-10S batteries.

Charge current：MAX 15A @MAX300W.

Discharge current：

Recycle / External mode Max 15A @300W.

Internal mode Max 3A @15W.

Lithium battery cut-off voltage can be adjusted at

will (TVC function).

Measures battery voltage, battery internal

resistance, and balances lithium packs

automatically.

Measures / outputs PWM/PPM/SBUS standard

signals with an accuracy of 1 microsecond.

Constant current and constant voltage source

output, customizable 1-28V constant voltage,

0.5-15A constant current.

Can be adapted for charging consumer-grade

drone batteries.

Multi-language user interface.

Multi-language voice broadcast, with customizable

voice packs.

Easily upgradable via USB.

@ToolkiRC 2022

M7AC Layout

Front

Back

Display

Scroll wheel

Output port

Balance port

DC input

TF card

Exit

Cooling fan

Speaker

Signal port

USB

output

AC input

AC switch

@ToolkiRC 2022

Quick start

1，Connect a 7-28V or AC 100-240V power supply or

input battery to the input port on the back of the M7AC.

2，The display shows the boot logo and stays for 2

seconds.

3，A welcome sound (voice pack dependent) is played

simultaneously.

4，After booting up, the screen enters the main

interface as shown below:

5，Press and hold [Exit] to enter the auxiliary function

interface.

6，Scroll [Scroll Wheel] to switch between pages.

7，With the charger idle, short press [OK] to set the

charging parameters. Press [OK] during the charging

process to adjust the amperage or stop the charge

process.

8，With the charger idle, Press and hold [OK] to enter

the system setting interface.

9，Short press [Exit] or return to the previous interface.

@ToolkiRC 2022

Charge and discharge settings

In the main interface, select and short press [OK] to

enter the charging function, open the battery selection

option in system settings, and the following interface will

be displayed.

1. Battery type setting

Scroll [Scroll Wheel], and select one of the presets,

or create a new battery. Up to 32 battery files can be

created. Press [Enter] to enter a specific battery setting,

the display is as follows:

@ToolkiRC 2022

Move the cursor to [Battery Type] and press [OK] to

modify the battery type, the display is as follows:

The charger supports charging and discharging of 6

types of batteries: Lipo, LiHV, LiFe, Lion, LTO, NiMh, and

PB. There is also a smart battery mode to choose from.

Tabla de contenidos

Otros manuales de Cargador de baterías de ToolKitRC

ToolKitRC

ToolKitRC Q6AC Manual de usuario

ToolKitRC

ToolKitRC M6 Manual de usuario

ToolKitRC

ToolKitRC M7 Manual de usuario

ToolKitRC

ToolKitRC Q4AC Manual de usuario

ToolKitRC

ToolKitRC C6 Manual de usuario

ToolKitRC

ToolKitRC C3 Manual de usuario

ToolKitRC

ToolKitRC C4 Manual de usuario

ToolKitRC

ToolKitRC M6DAC Manual de usuario

ToolKitRC

ToolKitRC M8 Manual de usuario

ToolKitRC

ToolKitRC M4 Pocket Manual de usuario

ToolKitRC

ToolKitRC M8 Manual de usuario

ToolKitRC

ToolKitRC M4Q Manual de usuario

ToolKitRC

ToolKitRC M6D Manual de usuario

ToolKitRC

ToolKitRC M9 Manual de usuario

Manuales populares de Cargador de baterías de otras marcas

AA Portable Power Corp

AA Portable Power Corp Universal Smart Charger Manual de usuario

Enelion

Enelion Vertica Manual de usuario

RCA

RCA CHU6 Manual de usuario

ANSMANN

ANSMANN ALCT 6/24-10 Manual de usuario

Hitachi

Hitachi UC 18YRSL Guía de solución de problemas

Olympus

Olympus B-20 LPC Manual de usuario

Exibel

Exibel ZH1708143 Manual de usuario

Lenmar

Lenmar Mach 1 Manual de usuario

CTEK

CTEK MXS 5.0 Manual de usuario

ABB

ABB HT842379 Manual de usuario

Nitecore

Nitecore Superb Charger SC4 Manual de usuario

Renogy

Renogy RBC2125DS-21W Manual de usuario

Braun

Braun BWC02M Manual de usuario

CTEK

CTEK MXS 3.6 Manual de usuario

Black & Decker

Black & Decker BDV090 Manual de usuario

Trinity

Trinity DPD Manual de usuario

Hulkman

Hulkman Sigma 1 Manual de usuario

IKEA

IKEA koppla Manual de usuario