clearance; then, after tightening the Cap Screws (#74 x 2 pcs),
Remove Cap Screws (#18 & #39 x 4 pcs) and Frame Assy. (203)
which to do it .Obviously, the less the tool is abused, the better.The
to remove Valve units. One Valve will stay on Spacer (#14) and can
complete Valve Assembly (should then have free motion of about
second Valve mounted on Screw (#9) in from other side and
Assemble one Valve on Spacer (#14). Holding Allen wrench, bring
#16). Using two Allen wrenches, unscrew Throttle Valve Screw (#9)
Loosen Set Screws (#28) and remove Adjustable Valve Seats (#5 &
Rollers (#46 x 4 pcs) can be taken out the front end of the Frame.
Spacer (#32). Piston Rod Assembly with Feeder Blade (#47) and
from Cylinder Housing. After taking off Piston(#30) and Piston Stop
the operating speed of the tool and may cause damage to it.
using 1/4" (6.35mm) ID air hose. Higher pressures will not increase
Air pressure should be maintained at 85-96 PSI (5.98-6.68 kg/cm2)
AIR PRESSURE
tool for a long and useful work life.
Please take care in handling, operation and maintenance of your
matter that is inside the tool will reduce its Operational efficiency.
cycling completely. Obviously, moisture, dirt or any other foreign
check to make sure that the application is correct and that the tool is
fastener. If for any reason you are not getting complete closure,
also note that the tool should make a complete closure of the
Far when you use it in the direction of your application. Please
tool should be handled firmly in your hand and don't stretch too
TO ASSEMBLE
1/16").
be disassembled after removal from Housing.
THROTTLE
PRECAUTIONS MAY RESULT IN SERIOUS
MAY RESULT. FAILURETO FOLLOW THESE
AWAY FROM ALL MOVING PARTS. INJURY
THE FRONT OF JAWS OF THE TOOL AND
KEEP HANDS AND CLOTHING AWAY FROM
DO NOT POINT THE TOOL AT ANY PERSON.
INJURY.
clearance should be rechecked.
promptly from stock. PLEASE SEE C-RING STYLES CHART
and #50). Remove Magazine Assembly(#73) and Feeder Guide Rail
Remove Flexlock Nuts(21) and Jaw Bolts (#74).Take out Jaws(#40
request. Use only parts that are specifically fabricated for the AC
replacement parts for repairs. Parts price lists are available upon
and have it checked for proper operation. ANN-CHAIN will ship
If any tool is not operating properly, remove it from service at once
for further details regarding materials, points and size of C-RING.
These rings are available from ANN-CHAIN and will be shipped
oiled, periodic oiling in small amounts may increase the serviceable
Although the jaws and other moving parts of the tool do need to be
A good grade of oil that emulsifies in water is recommended for air
Lubricators and Filter Units for proper lubrication and clean, dry air.
To insure long, trouble-free service, we recommend Air Line
moisture in the air line will adversely affect the smooth operation
sufficient to provide a constant and even flow of clean, dry air. The
The air line should have an attached air line filter and regulator
filter should be installed as close as possible to the tool. Dirt or
PNEUMATIC CLIP RING TOOL AC02, AC03,AC04
to take a long, hard look at your work and choose the best way in
a variety of other things. The most important point to remember is
a group of wire, the tool is frequently used as a pusher puller and/or
into foam, it should be cleaned occasionally. Also, when"grabbing"
area of maintenance to be conscious of is when pushing the tool
this is like any other tool and should be properly maintained. One
It should be kept in mind that in using the air powered clip ring tool,
in most operations the tool is used 90 degrees to the work performed.
The air powered clip ring tool should be held firmly in the hand and
OPERATION
and shorten its useful life.
proper operational precautions may result in damage to your tool
is of high quality and made to exacting standards, failure to follow
pressures above 100 PSI (7.03 kg/c
dirt and other foreign matter and do not operate the tool at air
working order, do not drop the tool, keep the mechanism free from
For best operating results and long life, maintain the tool in good
OPERATING INSTRUCTIONS & PARTS LIST
). Although your clip ring tool
Feeder Blade, Rollers and Piston Rod
Jaws, Magazine, Feeder Guide Rail
TO DISASSEMBLE
model tool which you own.
(#204).
REPAIR AND SERVICE PARTS
C-RINGS
TEL: 886-4-7521297 FAX: 886-4-7521293
CHANG HUA CITY, TAIWAN, R.O.C.
NO.65-5, LANE 540, YOAN-FONG RD.,
ANN-CHAIN ENTERPRISE CO., LTD.
LUBRICATION
life of the tool that receives heavy use.
MANUAL OILING
tools.
of the tool and decrease its serviceable life.
AIR FILTER AND REGULATOR
Spacer (#32), Piston (#30) and Flexloc Stop Nut (#21). Insert
Magazine must be held tight against Side Plate while checking this
clearance between Magazine Shoe (#76) and Feeder Blade (47).
between Magazine (#73) and Side Plate (#35R) to produce a
Before tightening Cap Screws (#74), insert enough Shims (#78)
ADJUSTMENT OF MAGAZINE
(#41 x 2 pcs) into Jaws (#40 & #50), side jaws into place and
Assembly Latch(#45) and Latch Pin Clip (#43).Insert Jaw Bushings
(#64) tight. Continue turning to desired Pusher Spring tension and
Pusher spring (#70), slide into Bracket and insert lower Cap Screw
With Feeder Arm (#51) in place, assemble Feeder Guide Rail(#204).
Throttle Stem (#17) and then assemble Frame to Housing.
MAGAZINE
complete assembly.
FEEDER GUIDE RAIL
lock with Nut (#67).
2pcs) and Rollers (#46 x 4 pcs). Put in Frame. Mount Piston Stop
Onto Piston Rod (#48) mount Feeder blade (#47), Roller Pins(#49 x
FEEDER BLADE, ROLLERS, PISTON ROD
Piston (#30) and Piston O-Ring (#29).
off Adjustable Valve Seat until leak stops. If leaks do not stop, check
be raised from its Bushing Seat, causing air leakage. To correct back
If an Adjustable Valve Seat is turned too far, the opposite Valve will
TO LOCATE AND CORRECT AIR LEAKS
Handle. After finer adjustment, lock Valve Seats in place with Set
Front Valve Seat (#16), turning until air stops exhausting through
leaking through Valve. Using Throttle Stem (#17) to turn, install
front Valve closed with a 3/8" dia. turn Valve Seat in until air stops
Adjustable Valve Seat (#5). With air partly turned on and holding
With Throttle Spring Locator (#7 & #8) in place, partially screw in
THROTTLE VALVE ADJUSTMENT
Screws (#28) in Housing casing.
