Tong Lung PL2-ZW Manual de usuario
123
456
789
0
USER MANUAL
TEMPLATE
45 40 35
1-3/4" 1-9/16" 1-3/8"
Fit here on door edge
FOR BACKSET 70mm (2-3/4”)
FOR BACKSET 60mm (2-3/8”)
Mark Ø1" (25.4mm) hole at
center of door edge.
Ø54mm (2-1/8")
Attention : Please do not use the "electronic" screwdriver for installation.
Product :
Purchase Date :
Limited Warranty Statements
1. Warranty
The manufacturer warrants the Product to be free
from defects in material and workmanship for a period of 12 months
from the original date of purchase.
If you discover a defect in the Product covered by this warranty, we will repair or
replace the item at our option using new or refurbished components.
2. Exclusions
This warranty covers defects in manufacturing discovered while using the
Products as recommended by The manufacturer rather than occurred by the act
of God, and damages caused by misuse, abuse, and unauthorized modification.
3. Limited of Liability
The manufacturer will not be held liable for incidental or consequential losses or
damages to any act of God.
4. Reminder
Service requirement shall subject to the presentation of this warranty card
and defective parts to the manufacturer.
The warranty card will not be reissued if lost.
TOUCHPAD
ELECTRONIC DEADBOLT LOCK
1
PACKAGE CONTENTS
A
B
CDE
F
G
H
I
L
K
J
PART DESCRIPTION QUANTITY
A
B
C
D
E
F
G
H
I
J
K
L
Key
Cylinder
Deadbolt pad AssemblyTouch
Deadbolt Latch
Strike Plate
Mounting Plate
Receiver Assembly
Battery Cover
Drive-in Sleeve
2
1
1
1
1
1
1
1
1
3
5
2
Machine Screws
Wood Screws
Deadbolt Chassis Screws
2
Machine Screws
Qty. 3
Wood Screws
Qty. 5
Deadbolt Chassis Screws Qty. 2
J K
L
HARDWARE SCREWS CONTENTS
LATCH BACKSET ADJUSTMENT
Remarks:
Please notice the the latch box between two different backsets.slight differences in
180°
2 3/4" (70 mm)2 3/8" (60 mm)
70 mm
60 mm
3
1
2
2.1
1. Backset Determination
Backset is a distance from door edge to
centre of hole on door face.
Adjustable latch fits both backset of
2 3/8" (60 mm) and 2 3/4" (70 mm).
2. Change Latch Face
Determine which latch mounting method will
be used and make necessary adjustments.
No adjustment required for square latch
face plate.
a. Use a flat screwdriver to separate the
face plate.
b. Snap selected latch face plate onto back
plate.
Drive-in Latch
Drive-in Installation
Remove original latch faceplate.
Align the (I) as illustrated and
snap into the latch case.
drive-in sleeve
a
b
D
D
I
ASSEMBLY INSTRUCTIONS
4
3
4
5
2 3/4" (70 mm)
3. Latch Backset Adjustment
Determine if the latch (D) needs to be adjusted
to the 2 3/4" (70 mm) backset.
To adjust, rotate the latch until it stops.
Reverse the direction to return to the
2 3/8" (60 mm) backset.
4. Mark the Door with Template
Select the height and backset as desired on
the door face; use the TEMPLATE as an
indication to mark the centre of the circle on
the door face and the centre of the door
edge.
5. Drill Holes
Using the marks as a guide to drill a hole
Ø2 1/8" (54 mm) through the door face for
the lockset, then a hole of Ø1" (25.4 mm)
for latch.
D
ASSEMBLY INSTRUCTIONS
5
6
7
8
6. Mark the Outline of Latch Faceplate
Insert the latch (D) and ensure it is parallel to
the door face.
Mark the outline of the faceplate, then
take out the latch (D).
7. Chisel Space for Latch Faceplate
Chisel 5/32" (4 mm) deep along the outline
to allow the faceplate to be aligned with
the door edge.
Note: It is not necessary to chisel the door
edge for the faceplate installation if
you use the drive-in latch.
8. Install Latch
Insert the latch (D) into the door.
(Make sure the cross is on the bottom of the
latch.) Use 2 wood screws (K) to secure latch.
Please do not fully tighten the screws until
lock is completely installed.
Hardware Used
KWood screws x2
D
D
K
ASSEMBLY INSTRUCTIONS
You need to stay
this way up when
inserting the latch.
Make sure the cross in the
latch is on the bottom.
6
8.1
9
10
Install Drive-in Latch
Drive the latch (D) into the hole on edge of
door.
9. Mark the Outline of Strike
To identify the centre of strike: close the
door to lay the latchbolt against the door
frame. Mark the centre line on the doorframe
exactly opposite the latch hole in the door
edge.
10.1 Drill Hole on Door Frame
Measure one half of door thickness from door
stop and vertically mark centre line of strike.
Drill 1" (25.4 mm) hole, 1" (25.4 mm)
deep at intersection of horizontal and vertical
line of strike.
10.2 Chisel Space for Strike
Chisel 5/64" (2 mm) deep along the strike
outline to allow the strike to be aligned with
the doorframe.
D
D
ASSEMBLY INSTRUCTIONS
7
11
12
13
11. Install Strike on Door Frame
Install the strike plate (E) into your door frame
and tighten with wood screws (K).
12. Install Touchpad Assembly
Make sure the latch bolt is retracted.
13. Install AssemblyTouchpad
touchpadInstall cylinder (B) into the deadbolt
assembly (C) with tailpiece in horizontal
position inserted through hub of the latch.
E
K
D
ASSEMBLY INSTRUCTIONS
B
Hardware Used
KWood screws x2
horizontal position
C
C
Left-handed Right-handed
Hardware Used
8
LDeadbolt chassis screws x2
15
16
14. Install Assembly
Pass the IC wire under the latch (D) to the
interior side of the door, and insert the
tailpiece through the cross-shaped crank
of the latch
Touchpad
.
15. Install Inside Mounting Plate
Pass the IC wire through the wire hole of the
mounting plate (F). Fix the mounting plate (F)
with screws (L). If outside lock assembly is
lopsided, please loosen the screws to adjust
its position and tighten the screws again.
16. Identify Door Handing
Face the door from the outside. The
door is left-handed if the hinges are
on the left side of the door, whereas
the door is right-handed if the hinges
are on the right side of the door.
L
F
ASSEMBLY INSTRUCTIONS
Hinge Hinge
horizontal position
14
D
C
B
IC wire
Hardware Used
9
17
18
19
For right-handed
door
For left-handed
door
17. Adjust Thumb Turn Piece
Rotate the thumb turn piece to the LEFT at
45 degrees for right-handed doors.
Rotate the thumb turn piece to the RIGHT at
45 degrees for left-handed doors.
18. Install Receiver Module
Remove the battery cover (H)
(push it up first then pull it out).
19. Install Receiver Module
Connect the IC wire into the back of the
receiver module. Ensure that the deadbolt
tailpiece is engaged with turn piece, then
attach receiver module (G) to the door with
screw (J). Use the optional wood screw (K)
to secure the receiver module to wood doors
only.
JMachine screws x3
G
H G
G
F
K
J
ASSEMBLY INSTRUCTIONS
KWood screw x1
This screw is optional. It may not be necessary to
use this screw.
Tabla de contenidos
