TMT TI-5700 Manual de usuario

TI-5700

VER 101

WEIGHING INDICATOR

OPERATION MANUAL

DIGITAL WEIGHING INDICATOR TI-5700

- 2 -

NOTE

(1) The unauthorized copying of some or all of this manual is prohibited.

(2) The information contained herein is subject to change without notice.

(3) If there are any questions such as wrong or missing parts of the

contents listed in this manual, please contact us.

(4) To improve the product performance, functions can be changed with

no notice.

(5) Please understand that TMT does not have responsibility for a

demand related to loss, lost profit etc. caused by operating the

product, regardless of the third clause.

WARNING DEFINITIONS

This is warning & caution mark

This is hazard alert mark

This is useful information mark

DIGITAL WEIGHING INDICATOR TI-5700

- 3 -

INDEX

1. Precautions ..................................................................................................... 4

2. Introduction ...................................................................................................5

3. Description of Panels and Symbols ....................................................6

4. Installation ......................................................................................................8

5. Calibration ....................................................................................................12

6. Setting Mode ..............................................................................................18

7. General Function for Weighing Mode .............................................32

8. Weighing check & batching mode ...................................................36

9. Test Mode .....................................................................................................44

10. Solid State Relay and Control Inputs (OP-01) ...........................46

11. RS-232C Interface (OP-02) ..................................................................47

12. RS-422/485 Interface (OP-03) ...........................................................51

13. Analog Output (OP-04) ........................................................................52

14. Current Loop Output (OP-05) ...........................................................53

15. LAN IEEE 802.3 (OP-06) .......................................................................53

16. BCD Output (OP-07) ..............................................................................54

17. USB Host (OP-08) ...................................................................................56

18. ZigBee Wireless (OP-09) ......................................................................58

19. Bluetooth Wireless (OP-10) ................................................................59

20. Rechargeable Li-Po Battery (OP-11) ..............................................60

21. Specifications ............................................................................................61

22. Check Message ........................................................................................62

DIGITAL WEIGHING INDICATOR TI-5700

- 4 -

1. Precautions

Please be informed that we‟re not responsible for any incident or mishap caused

by partial modification of this product. To avoid such situation, customers need to

contact our customer service team or system installation staff in advance, and any

modification should be conducted under our surveillance.

Do not install the indicator in strong direct sunlight and dust.

Please confirm that the local voltage is correct for the indicator.

Do not use inflammable substances for cleaning.

Do not use the product in the rain. Keep it dry.

Avoid sudden changes of temperature if possible

Do not use the product in a place with a high-voltage current or severe

electronic noise.

Do not use the product in a place with severe vibration.

Do not put too much pressure to keys.

DIGITAL WEIGHING INDICATOR TI-5700

- 5 -

2. Introduction

◆The TI-5700 is a compact simple batch weighing indicator

◆Standard functions are as below

◊Main display of 6 digit FSTN LCD and LED backlight

◊3-stage limit comparison to check a mass value

◊8 item code comparison for batching applications

◊The accumulation to weight data and count

◊The average or peak hold functions

◊The zero and tare functions

◆Optional functions are as below

◊OP-01: 3 solid state relay and inputs

◊OP-02: RS-232C serial interface

◊OP-03: RS422 / 485 serial interface.

◊OP-04: 4~20mA / 0~10V analog output

◊OP-05: Current loop output

◊OP-06: LAN IEEE 802.3

◊OP-07: BCD output

◊OP-08: USB host

◊OP-09: ZigBee wireless

◊OP-10: Bluetooth wireless

◊OP-11: Rechargeable Li-Po battery

◊OP-12: Stainless steel mount bracket

◆Selection criteria for optional functions

OPTION

CASE 1

○

Select one of them

○

Select one

of them

○

CASE 2

○

X: Can‟t be selected with option.

(e.g., OP-07 can repeatedly select OP-08/11/12 and select one of OP-09/10)

OP-08 to 10 are must be selected before ordering.

DIGITAL WEIGHING INDICATOR TI-5700

- 6 -

3. Description of Panels and Symbols

3.1. Front panel

No.

Name

Description

Display

Display the weight data & message

Battery

Indicates when a battery has to be recharged

HI/OK/LO

Indicates the results of comparison

Zero

Indicates when the weight is zero

Accumulation

Indicates when there is accumulation weigh.

Tare

Indicates when the tare is included

Hold

Indicates when the hold function is set

Net

Indicates when the weight is the net weight

Wireless

Indicates when the wireless communicates data

Unit

Unit used to weigh

Stable

Indicates when the weight is stable

USB

USB host port for memory stick

CAL cover

CAL switch cover (For calibration)

ON/OFF key

Power ON/OFF of indicator

ZERO key

The key to make weight value as zero

＞key

The key to move a digit of one in the set & calibration mode

TARE key

The key to perform tare weight

∧key

The key to add a value of one in the set & calibration mode

NET/GROSS key

The key to select net or gross weight

+/- key

The key to select plus or minus of a value

F1 key

This key can be selected by operator in the set mode

ESC key

The key to escape from the present mode

F2 key

This key can be selected by operator in the set mode

ENTER key

The key to store/confirm setting value

DIGITAL WEIGHING INDICATOR TI-5700

- 7 -

3.2. Rear panel

No.

Name

Description

Battery cover

Lithium polymer battery compartment cover

Panel bracket

Standard panel bracket

Option panel cover

For OP-01, 02, 03, 04, 05, 06 and 07

Load cell connector

Connect the load cell

Ground terminal

Frame ground (F.G.)

DC jack

Uses the supplied adaptor (12VDC 1A )

The F.G. terminal must be grounded to avoid electric shock and interference

from static discharge.

DIGITAL WEIGHING INDICATOR TI-5700

- 8 -

4. Installation

4.1. Power supply

Use only approved power adaptor and batteries.

Do not connect incompatible products.

Use only batteries, chargers, adaptor, and enhancements approved by TMT for

use with this particular model.

The use of any other types may invalidate any approval or warranty, and may be

dangerous. For availability of approved enhancements, please check with your

dealer.

When the standard AC adapter is used

◊Check the power supply voltage

◊Must be uses the supplied AC adaptor.

◊A stable power source must be used;

An unstable power source may result in a malfunction.

◊Connect the DC jack to rear side of the indicator.

When the Li-Po battery pack is used

◊Refer to “21. Rechargeable Li-Po Battery (OP-11)”

4.2. Load cell connections

DIGITAL WEIGHING INDICATOR TI-5700

- 9 -

Connect the load cell wire to the connector, at the rear panel

◊Load cell wire color depends on the manufacturer of load cell, please check the

load cell specification.

◊It is possible to connect a 4 wire cable provided that pins EX+/SEN+ and pins

EX-/SEN- are shorted.

◊It is possible to connect eight (8) 350 ohm load cells.

◊If you connect other wires to load cell terminal wrongly, it may cause

damage in the indicator circuit.

Before connecting the load cell wire, you must power off and be sure to connect

the load cell wire to the terminal correctly.

◊The output voltage of a load cell is a very sensitive signal.

Don‟t weld near the load cell & indicator. Also, place the load cell cable away

from any noise source.

Adjustment of the load cell output

◊In case of reducing the output.

When the zero output is too large,

add a resistor between EX+ and SIG-.

This should shift the zero point to negative.

◊In case of increasing the output.

When the zero output is too small,

add a resistor between EX+ and SIG+.

This should shift the zero point to positive.

◊Use a metal film resistor in the range of 50kohm to 500kohm with a good

temperature coefficient. (Below 1%)

DIGITAL WEIGHING INDICATOR TI-5700

- 10 -

Verifying load cell output and input sensitivity

Adapt to the following inequality, when you design a weighing instrument using the

indicator and load cells.

EV: Excitation voltage [mV]

RO: Rated output [mV/V]

e: Weighing interval [kg]

LC: Rated capacity of load cell [kg]

N: Number of load cells

EV ×RO ×e

0.2 ≤LC ×N

(Input sensitivity is 0.2uV/D)

EXAMPLE

Load cell: N=1

Rated capacity: LC=1,000kg

Rated output: RO=2mV/V

Excitation voltage: EC=5000mV

Weighing interval: e=0.02kg

5000 ×2 ×0.02

0.2 = 1000 ×1

Regard the instrument as a good design

Tabla de contenidos

Manuales populares de Accesorios de otras marcas

Hillco

Hillco 2810 Manual de usuario

Siemens

Siemens QSA2700D Manual del operador

Contours

Contours ZY024 Manual de usuario

Saivod

Saivod VS621 Manual de usuario

Virtuox

Virtuox VirtuCLEAN 2.0 Manual de usuario

SCE

SCE ENVIRO-THERM SCE-TE170B24VSS Manual de usuario

Z-Wave

Z-Wave HSD-200Z Manual de usuario

turck

turck FMX-IM-2UPLI63FX Manual de usuario

Decagon Devices

Decagon Devices 10HS Manual de usuario

UPPAbaby

UPPAbaby Cup Holder Manual de usuario

Elko

Elko SmartSensor Leakage Wireless Manual de usuario

Grizzly

Grizzly H8371 Manual de usuario

Panasonic

Panasonic HG-T Series Manual de usuario

IFM Electronic

IFM Electronic Efector 250 Series Guía de referencia

DigiDesign

DigiDesign 888/24 I/O Manual de usuario

PROZIS

PROZIS QUAY Manual de usuario

patagonia

patagonia PSI Vest Manual de usuario

SFC Energy

SFC Energy EFOY GO! Manual de usuario