TMP MQi GT EVO Manual de usuario
USER MANUAL
V1.0
CONTENTS
Attach the
SN Code here
The SN Code of your scooter.
Please see P.4 for detailed information.
General Notice
Precautions
Safety Notice
Downloading the APP
Installation Guide
Parts Info
Dashboard and Combination Switches
Operation Guide
Battery Use and Maintenance
DOs and DON'Ts while Riding
Maintenance and Repair
Storage Method
Troubleshooting List
Technical Parameters
Maintenance Record
01
02
03
04
05
07
09
15
20
27
29
31
33
40
43
General Notice
Please read this User Manual carefully for proper operation before riding the scooter.
For your safety, please check whether the parts are in good condition according to this User
Manual before riding. Contact your dealer in time in case of any problems.
Please follow the traffic laws. Slow down on slippery roads in bad weather to allow greater
braking distance for your safety.
Please pay attention to deep water. It may cause rusting or failure of the motor, battery or
other parts if water level reaches wheel axle.
Do not dismantle the scooter on your own. Please contact your dealer for replacement or
purchase of original parts.
Do not lend your MQi GT EVO to those who can’t operate a scooter for others' safety and
preventing unnecessary damage to your scooter.
Please keep the User Manual properly.
Due to constant improvement of product functions and change of design, your scooter may
differ slightly from the one shown in this manual, Please refer to the actual product.
For more product information or maintenance need,
please visit our website: www.niu.com/en
0201
Precautions
Rider and Passenger
MQi GT EVO is not designed for a ride of more than 2 persons.
Road Conditions
MQi GT EVO is not designed for off-road use.
This User Manual should be deemed as a permanent document of MQi GT EVO. If this
scooter is transferred to others, this User Manual should also be handed over to the
new owner.
Reproduction or reprint of any part of this User Manual is strictly prohibited.
WARNING: Failure to follow the instructions herein may lead to serious casualties.
ATTENTION: Failure to follow the instructions herein may lead to personal injury or
scooter damage.
0403
Safety Notice
Using a safety helmet and protective goggles is strongly advised.
You are advised to take proper training or exercise before using on open roads.
Please follow the Operation Guide (P.15) to fully understand how to properly operate the
scooter.
It should be noted that the braking distance in bad weather will be much longer. Please avoid
braking on paint markers, manhole covers, and oil stains to prevent slipping. Pay extra
attention when riding through railway crossings, junctions, tunnels, and bridges. Slow down
if road conditions are unclear.
Do not use high beam indiscriminately. Continuous use of high beam may disturb the vision
of other drivers and pedestrians.
Do not use mobile phones or other electronic devices which may draw your attention while
riding.
Do not change the lane without signaling. Changing the lane at will is one of the major
causes for accidents. When you need to change the lane, remember to switch on the Turn
Signal Indicator first. Always check the vehicles approaching from behind before changing
the lane.
Downloading the APP
Step 1
Step 2
Step 3
Functions such as checking battery level, locating, and management can be implemented on the
electric scooter through the app.
NOTE:
The mobile phone system is required to be at least Android 4.0 or iOS 8. Make sure that the
mobile phone has been connected to the Internet when running the app (Wi-Fi / 2G / 3G / 4G).
Scan the QR code below to download the APP
titled Niu E-Scooter.
Run Setup after downloading and register.
Please scan the QR code on the inside of cover
page for app registration.
0605
Installation Guide
Step 1
Step 2
Step 3
Open the Accessories Box to take the tools.
Install the rearview mirrors into the mounting holes on dashboard and turn it
clockwise. The bolt shall be screwed in for more than 15 mm.
Adjust the rearview mirror to an appropriate position and then tighten nuts on the
rearview mirror with a spanner. Properly set the dust cover.
Step 1
Step 2
Step 3
Place the 12V battery in side the battery compartment under the floor board, with
electrode terminals facing forward. Attach the red positive electrode terminal with red
wire, and black positive electrode terminal with black wire.
Mount the metal battery fixture to body with screws provided.
Finally, mount the plastic cover to the floor board with screws provided, and the
assembly is complete.
0807
Parts Info
Right
Combination
Switch
Turn Signal
Indicator
Headlight
Right
Reflector
Handrail
Reflector
12V Battery
compartment
Left
Combination
Switch
Taillight
Rearview
Mirror
Saddle
Central
Stand
Side
Stand
Left
Reflector
1009
Dashboard and Combination Switches
13 14 15 16 17 1918 20
1 2 4 5 6 7 8 9 10
11 12
3
Low battery
Ready
OBD system
Left turn High beam
Right turn
Riding mode Currently selected riding mode E-SAVE/DYNAMIC/SPORT;
Power recovery Displayed when power recovery is ongoing;
Cruise control Displayed when the cruise control function is activated;
Maintenance rating Displayed when the vehicle is not in good condition;
Error code Displayed when the vehicle system reports an error;
Bluetooth state Displayed when the vehicle is connected to Bluetooth;
Automatic headlight Displayed when the automatic headlight function is
activated ;
Cloud service state Displayed when the cloud service function is activated;
Dual battery
synchronization state Displayed when two batteries have the same power;
Energy-saving state
1
2
3
4
5
6
7
8
9
Clock;
Week and date;
10
11
12
Displayed at the time of efficient energy conversion (a
speed of more than 3 km/h delivered per ampere of
power output);
1211
Real-time power
13
Current battery level and battery bar (two battery
bars respectively represent the levels of two
batteries), and the estimated remaining mileage;
15
Air temperature, current weather conditions and temperature;
16
14
Real-time speed;
17
18
Energy consumption curve, curve of change in energy consumption during riding;
19
Total mileage, total riding distance;
20
Riding data, total riding time, mileage, average energy consumption, average speed ;
Satellite positioning signal;
Mobile network signal.
Parking and Other
21
1
2Navigation information Enabled when connected to the meter through the APP
of Niu Technologies.
Real-time power Displaying a single battery bar when only a single
battery is available;
Zhongshan East
2nd Rd
1413
Hazard Light (flashing lights)
Both the left and right turn signal indicators
will flash when the Hazard LIght button is pressed.
High/Low Beam
Push the button up to turn on the high beam;
push the button down to turn on the low beam.
Turn Signal Indicator
Push the button left to turn on the left turn
signal indicator;
Push the button right to turn on the right turn
signal indicator.
Horn
Press the horn button to sound the horn, and
release it to stop.
Cruising Mode
Press the button to cruise at current speed.
Press again or brake to turn Cruising Mode off.
Cruising Mode
Hazard Light (flashing lights)
High/Low Beam
Turn Signal Indicator
Left-hand Combination Switch
1
1
2
2
3
3
4
Horn
5
Overtaking Light Button
6
4
56
Overtaking Light Button
To signal overtaking with flashing light, the rider
may press and release the Overtaking Light
Button repeatedly.
Scooter Light Adjustment：
Push the button to the right to turn off low beam lights;
Push the button to the middle to turn on the outline
marker light and the license plate light;
Push the button to the left to turn on the headlamp.
1
2Safety Switch
Riding Mode
Scooter Light Adjustment
Start Button
Right-hand Combination Switch
1
2
3
4
3
4
Safety Switch
Push the top button to cut off the power system.
If you press the button while riding, the scooter will
start to coast (power will be cut off);
Push the bottom button to restore power and ride normally.
Riding Mode
Press the left/right button to switch between
riding modes.
Start Button
Press the Start button and the scooter will be
ready to go.
1.Hold the Start button to turn on the vehicle;
2.Press the Start button and the scooter will
be ready to go;
3.Double tap the Start button to open the seat
compartment.
1615
Keyhole
USB Port
Operation Guide
Front Storage Area
1
2
1
2
Key
Anti-theft Lock
Ring
Keyhole
Unlocking the anti-theft lock
Insert the spare key into the emergency key
hole, push it inward, and clockwise rotate
to the “UNLOCK” position, to release the
faucet lock.
Opening the saddle
Insert the spare key into the emergency key
hole, and counterclockwise rotate to the
“OPEN” position, to open the battery
compartment cover.
Tabla de contenidos
