TMG INDUSTRIAL 25100 Manual de usuario

Page 0of 12

Page 1of 12

Main specifications

Overall assembled size : W7.62 x L29.9 x H3 (m) / W25 x L98 x H10 (ft)

Shoulder height : H1.2 (m) / 4ft

Door : W1.2 x H2 (m) / 4 x 6.6 (ft)

Prior to assembly

Please read the instructions carefully before installation. It is important to follow your

local safety regulations and industry standards during installation. Regulations may

include but are not limited to :

Safety helmets, protective eyewear, and clothing

Safety harnesses for all elevated workers

Proper ladder, cage, and safety operation

Check all components and parts before installation. All parts are marked with a part

number, please refer to the parts list to make sure you have all parts.

Choose a day with low or no wind to install, assembly is hard in heavy wind. Do not

make any alterations to the structure. Do not hang any weights on the frame during

installation, including parts. We are not responsible for any damages or injuries caused by

inappropriate installation, unauthorized modifications or extreme weather.

This building is not intended for human occupancy.

It is recommended to tape or add foam/rubber on the frame where joints connect and

where it touches the cover. This will help extend the life span of the cover.

Read the following item list carefully and count the number of items to ensure that all

parts are included prior to setup.

Page 2of 12

TMG-GH25100 Part List

Parts

code

Graphical

Description

Qty

Peak arch tube

Upper rafter tube

Shoulder tube

(front and rear truss)

Roof purlin

(horizontal tube)

161

Base plate

Expansion bolt M12x100mm

160

Door column base plate

Vertical tubes

Door left vertical tubes

Door right vertical tubes

Door horizontal tube

Door frame column left tube

Door frame column right tube

Door cross tubes

10A

Door cross tubes

10B

Door frame cross pull tube

Page 3of 12

Ceiling cross bar

Tube clamp

Film rolling machine guide tube

Roll film tube

14A

Roll film tube

Door buckle

Film rolling machine

Reed groove

17A

Clip spring

Eight clip spring

Pressure film carrier

Half round head bolt M6x50

Self locking bolt

M10x70mm and nuts

168

Hex bolt

M10x70mm and nuts

320

Hex bolt

M10x30mm and nuts

Hex bolt

M10x100mm and nuts

Page 4of 12

Self tapping screw #12x25

562

Self tapping screw #12x35

216

Square plug

Round plug（φ25）

Braided rope

1 bundle

(100m)

Top cover film

30A

Front and rear door film

Adhesive tape

Socket wrench

Hex wrench

Board 150x15x2000mm

(not included)

Installation steps

Step 1 : Review the whole structure and choose the proper installation site

Choose a solid flat level ground area to set up the building. Do not install the

building on soft ground, wetland, uneven surfaces, sloped surfaces.

We strongly recommend that you build the structure on a solid foundation such as

cement and use anchor bolts on all base plates.

Page 5of 12

Be aware of the surrounding area. Do not set up the building near snowdrifts, open

flames or exposed electrical wires. Do not keep heat sources near the fabric cover.

Keep the building surroundings clear at all times

Mark the ground in the final building location with a line showing the positions of

base plates, front doors. All lines should be drawn from center to center of all base

plate tubes. Diagonal line X must be equal to Y.

Base plates : all base plates must be installed firmly with expansion bolts (#5B) on

this step (refer to figure 1).

Parts used in this step :

(48) Base plate (#5)

(8) Door column base plate (#6)

(160) Expansion bolts (#5B)

Figure 1

Step 2 : Assemble all trusses

The building includes 24 trusses : (2) front and rear truss, and (22) middle trusses.

Parts used to install the front and rear truss in this step (refer to figure 2) :

Page 6of 12

(1x2) Peak arch tube (#1)

(2x2) Upper rafter tube (#2)

(2x2) Shoulder tube (#3A)

(1x2) Ceiling cross bar (#11)

(8x2) Hex bolt (#22)

(2x2) Hex bolt (#23)

Figure 2

Parts used to install (22) middle trusses in this step (refer to figure 3) :

(1x22) Peak arch tube (#1)

(2x22) Upper rafter tube (#2)

(2x22) Shoulder tube (#3)

(1x22) Ceiling cross bar (#11)

(8x22) Hex bolt (#22)

(2x22) Hex bolt (#23)

Figure3

Page 7of 12



Lay down all (24) trusses on the ground as figure 4 when the assembly is all

completed and before moving to next step.

Figure 4

Step 3 : Put up all trusses (refer to figure 5)



Put up the front truss, use hex bolt (#22) to secure the truss to the base plates.



Parts used in this step :

(4) Hex bolt (#22)

Figure 5

Page 8of 12



Repeat above step to put up all other trusses (from 2th to 24th truss), and

connect all purlin. Now the whole structure is completely up. (refer to figure



Parts used in this step :

(7x23) Roof purlin (#4)

(7x24) Self locking bolt (#21)

(4x23) Hex bolt (#22)

Figure 6

Step 4 : Installation of front and rear trusses (refer to figure 7)

(2x2) Vertical tubes (#7)

(1x2) Door left vertical tubes (#8L)

(1x2) Door right vertical tubes (#8R)

(4x2) Door horizontal tube (#9)

(1x2) Door frame column left tube (#9L)

(1x2) Door frame column right tube (#9R)

(2x2) Door cross tubes (#10)

(2x2) Door cross tubes (#10A)

(1x2) Door frame cross pull tube (#10B)

(6x2) Tube clamp (#12)

(8x2) Half round head bolt (#20)

(16x2) Hex bolt (#22)

(6x2) Hex bolt (#23)

(4x2) Square plug (#27)

Page 9of 12

Figure 7



The whole structure inspection: check all components and trusses to make

sure the whole structure is squared to the base line drawn at the step 1. All

trusses must be set up righted at 90 degree. All purlin must be straight in line.

If any purlin are not in line with they will need to be corrected before moving

to the next step.



Now it is the time to secure all bolts and nuts firmed on the structure. But do

not over-tight the bolts, otherwise the tubes might be damaged.

Step 5 : Installing boards (#34) and reed groove (#17) (refer to figure 8)



Fix the board (#34) with self tapping screw (#26).



Fix the reed groove (#17) with the self tapping screw (#25).



Parts used in this step :

(98) Reed groove (#17)

(490) Self tapping screw (#25)

(216) Self tapping screw (#26)

(68) Boards (#34)

Este manual sirve para los siguientes modelos

Tabla de contenidos

Otros manuales de Kit de invernadero de TMG

TMG

TMG TMG-GHD3060 Manual de usuario

TMG

TMG TMG-GH2030BL Manual de usuario

TMG

TMG TMG-GH1010R Manual de usuario

TMG

TMG TMG-GH1020R Manual de usuario

TMG

TMG TMG-GH813 Manual de usuario

TMG

TMG TMG-GH2060 Manual de usuario

TMG

TMG TMG-GH1030R Manual de usuario

TMG

TMG 1260 Manual de usuario

TMG

TMG TMG-GH826 Manual de usuario

TMG

TMG TMG-GH1020P Manual de usuario

Manuales populares de Kit de invernadero de otras marcas

ACD PRESTIGE

ACD PRESTIGE MR3 H Manual de usuario

Vitavia

Vitavia VA0040-TRP Manual de usuario

VegTrug

VegTrug Nursery Manual de usuario

Riverstone Networks

Riverstone Networks Monticello 041315V Manual de usuario

STC

STC Easy Grow 6x12 Greenhouse Manual de usuario

CLIMA POD

CLIMA POD Spirit V7 Series Manual de usuario

Vitavia

Vitavia GAIA JUMBO Manual de usuario

Palram

Palram Harmony 6'x4' Manual de usuario

ClearSpan

ClearSpan Storage Master 104598 Manual de usuario

Sproutwell

Sproutwell GRANGE - 5 Manual de usuario

ACD

ACD Piccolo 03 Manual de usuario

Growhouse

Growhouse Lean To 6 x 8 Manual de usuario

Riverstone Networks

Riverstone Networks Grower's 181010V Manual de usuario

GrowSpan

GrowSpan 500 Series Manual de usuario

Robinsons

Robinsons 5ft Wide LEAN-TO Manual de usuario

Botanica

Botanica E Manual de usuario

PNI

PNI SP6000 Manual de usuario

Hortus

Hortus 211-203 Manual de programación