TJERNLUND Cool Breeze CB14 Manual de usuario
DESCRIPTION
The Tjernlund Cool Breeze™ Garage Fan ( odel CB14) pulls hot air from
the garage ceiling and exhausts it into the garage attic where it then can
flow out of the ridge, roof or gable vents. Outdoor air replaces the hot
exhausted air lowering air temperatures and reducing the thermal heat gain
of the garage’s floor, structure and contents. The fan can also be used to
exhaust non-combustible contaminants from the garage.
The CB14 comes with an adjustable temperature activation switch for sim-
ple, automatic operation. It can also be wired for manual or automatic oper-
ation. Other controls are available and sold separately.
Included in the CB14 is the fan assembly, intake plenum, ceiling radiation
damper, fan intake grille, (2) outdoor intake grilles, mounting brackets and
hardware packet with instructions.
SPECIFICATIONS
Blower: 1200 CF Temperature Switch: Adjustable from 90F to 130F
otor: 120 VAC ~ 60 Hz Ceiling Radiation Damper: 3 Hour, 212F fusible link
2.17 Amps maximum
Grilles: (1) 18” x 18”
Impeller: 30 degree, steel (2) 12” x 12”
GENERAL INFORMATION
Each Cool Breeze™ Garage Fan is electrically factory line tested before shipment. After opening carton, inspect thoroughly
for shipment damage. Fan should rotate freely and all electrical wires and connections should be secure. If any damage is
found, notify freight carrier and your distributor immediately and file a concealed damage claim.
OPERATION
The CB14 can be wired to be controlled manually by a wall switch (not included), by the included temperature switch, or
both. Also available from Tjernlund are wall mount timers (P/N 950-9300) and wireless wall switches (P/N SWS). Contact
Tjernlund for more information on these controls.
INSTALLATION
WARNING
The CB14 must be installed by a qualified installer in accordance with these instructions and all local codes or in their
absence in accordance with the latest editions of the International Residential Code, International Electrical Code or prevail-
ing local codes. Improper installation can create a hazardous condition such as fire, electric shock or personal injury.
To reduce these risks significantly, use this unit only in the manner intended by the manufacturer. If you have questions,
contact Tjernlund Products. Always disconnect the unit from its power source before installation and servicing.
CAUTION: For general ventilation use only. Do not use to exhaust hazardous or explosive materials and vapors.
Cool Breeze™ Gara e Fan Model CB14
©2013 TJERNLUND PRODUCTS, INC. ALL RIGHTS RESERVED P/N: 8504203
TJERNLUND PRODUCTS, INC.
1601 Ninth Street • White Bear Lake, N 55110-6794
PHONE (800) 255-4208 • (651) 426-2993 • FAX (651) 426-9547
Visit our web site • www.tjernlund.com
READ OWNERS INSTRUCTIONS CAREFULLY PRIOR TO INSTALLATION.
THESE INSTRUCTIONS MUST REMAIN WITH EQUIPMENT. DO NOT DESTROY.
TOOLS REQUIRED
• Drywall Saw
• Drill with 1/4" Hexagonal Torque Bit, Flat Head Bit and 1/16” Drill Bit
• Flathead Screwdriver
• 6’ 2” x 4” Board
INSTALLATION
LOCATION WARNING
ount garage fan inside the attic keeping in mind the electrical and activation sources. Locating the CB14 away from the
intake vents may lead to more complete garage coverage and better results.
Locating rows of drywall screws may help identify the location of joists along the ceiling. ake sure the location you choose
is a suitable considering:
1) Electrical, gas, water lines or structurally critical areas of your home that may be located in your attic
2) The combined height of the fan, intake plenum and open radiation damper in relation to the roof pitch
3) Electrical access for the fan motor
4) Air flow paths to gable, ridge or roof vents
1. Outline a 16”x16” square on your garage ceiling at the desired fan location
considering the above points.
2. Cut along outline with drywall knife to create hole opening (Figure A).
3. Intake plenum can be pushed up into the hole and secured from the garage (Figure B) or placed on ceiling from attic and
secured from above (Figure C). Center the intake plenum along opening in the drywall and rotate so that the sides
with the three mounting holes (used later) are perpendicular to the joists/trusses.
3a. If mounting the intake plenum from the garage:
-Secure 2 2” x 4” boards between the joists and along edges of the hole. These can typically be cut to 22.5” and
secured with screws or nails if joists are 24” on center.
-Insert intake plenum into hole from garage and secure it by driving screws through the 3 mounting holes on each
side of the intake plenum and then through the drywall and into the secured 2” x 4” boards.
Figure A
Figure CFigure B
3b. If mounting the intake plenum from the attic:
-Use the included mounting brackets. Break apart the mounting brackets as shown (Figure D).
- Bend the mounting bracket ends and insert one mounting bracket into the other to form a sliding mounting bracket
(Figure E). Repeat with the other set of brackets to form two separate sliding mounting brackets.
-Expand the mounting bracket to the full width of your trusses or joist (Figure F). Hold against intake plenum and
secure using provided screws the mounting bracket at each of the three mounting holes on the intake plenum.
-Repeat on the other side of the intake plenum.
-Secure both mounting bracket ends to the truss or joist. Repeat on the other side of the intake plenum.
4. anually insert crimped end of fan into the radiation damper. Drill 1/8” holes through both the radiation damper and fan
on the 4 sides of the fan assembly (damper and fan) (Figure G). Secure the radiation damper to the fan using the 4
included screws (Figure H).
5. Place fan assembly (damper and fan) onto the intake plenum with radiation damper up (Figure I).
Drill 1/8” holes through both the fan and plenum on the 4 sides of the fan. Secure the fan to the
plenum using the 4 included screws.
6. Pull the wings of the radiation dampers together and secure them together using the fusible link.
7. Wire the fan using the wiring diagrams listed in the Wiring section.
Figure I
Figure H
Figure G
Figure F
Figure E
Figure D
8. Use a flathead screw driver to adjust the temperature setting of the thermostat switch to the desired activation
temperature. The fan will operate once that temperature is reached and run until the garage is approximately 20F cooler
(see chart below).
Note: The switch is sensing the temperature at the location of the switch (the bottom part of the attic), so adjust the setting
slightly higher than the temperature you would like to maintain in your garage.
9. Secure the fan intake grille against the ceiling of the garage so the louvers face the intake
grilles. Align the holes of the grille and theholes of the intake plenum (Figure J).
10. Cut 12” x 12” holes in your garage door or garage walls and mount the included in fresh air
intake grilles to allow outdoor air to enter the garage space as the fan operates (Figure K).
ake sure the added depth of the grilles clears the top frame of the garage door
11. Position grilles over the opening ensuring the louvers face downward to prevent rain from
entering the garage. ark mounting holes and drill small pilot holes.
12. ount grilles with provided screws. Do not overtighten screws. Tighten just so the screw
head meets the grille.
REPLACEMENT PARTS
Component Part Number Component Part Number
otor Kit 950-0423 Ceiling Radiation Damper 950-3371
Impeller Kit 950-0421 Thermostat Switch 950-3372
Fan Intake Grille 950-3370 Garage Door Grille 950-3373
WARRANTY
70 80 90 100 110 120
CUTOFF TE PERATURE (BREAK)
130
CB14 PERFOR ANCE
75 85 95 105 115 125 135
70 80 90 100 110 120
SET TE PERATURE ( AKE)
130
75 85 95 105 115 125 135
65
65
S ALLER
RANGE
TOWARDS
LOW
LARGER
TE PERATURE
RANGE TOWARDS
THE HIGH END
END
TJERNLUND LIMITED ONE YEAR WARRANTY
Tjernlund Products, Inc. warrants to the original purchaser of this product that the product will be free from defects due to faulty material
or workmanship for a period of (1) year from the date of original purchase or delivery to the original purchaser, whichever is earlier.
Remedies under this warranty are limited to repairing or replacing, at our option, any product which shall, within the above stated war-
ranty period, be returned to Tjernlund Products, Inc. at the address listed below, postage prepaid. THERE ARE NO WARRANTIES
WHICH EXTEND BEYOND THE DESCRIPTION ON THE FACE HEREOF, AND TJERNLUND PRODUCTS, INC. EXPRESSLY DIS-
CLAI S LIABILITY FOR INCIDENTAL OR CONSEQUENTIAL DA AGES ARISING FRO THE USE OF THIS PRODUCT. THIS
WARRANTY IS IN LIEU OF ALL OTHER EXPRESS WARRANTIES AND NO AGENT IS AUTHORIZED TO ASSU E FOR US ANY
LIABILITY ADDITIONAL TO THOSE SET FORTH IN THIS LI ITED WARRANTY. I PLIED WARRANTIES ARE LI ITED TO THE
STATED DURATION OF THIS LI ITED WARRANTY. Some states do not allow limitation on how long an implied warranty lasts, so
that limitation may not apply to you. In addition, some states do not allow the exclusion or limitation of incidental or consequential dam-
ages, so that above limitation or exclusion may not apply to you. This warranty gives you specific legal rights and you may also have
other rights which may vary from State to State. Send all inquiries regarding warranty work to Tjernlund Products, Inc. 1601 9th Street,
White Bear Lake, N 55110-6794. Phone (651) 426-2993 • (800) 255-4208 • Fax (651) 426-9547 • Email [email protected].
Figure J
Figure K
WIRING
T-STAT
RED
RED
GREEN
WHITE
BLACK
TO OTOR
CB14 AS SHIPPED
FIGURE 8089017 6-5-13
T-STAT
CB14 TI ER SWITCH CONTROLLED
FIGURE 8089020 6-10-13
GREEN
NL1
RED
RED
WHITE
BLACK
TI ER SWITCH
10 IN
20 IN
30 IN
60 IN
OFF
BLACK
WHITE
GREEN
RED
T-STAT
BLACK WHITE
CB14 TE PERATURE CONTROLLED
FIGURE 8089018 6-5-13
GREEN
RED
RED WHITE
GREEN
RED
N
L1
T-STAT
CB14 CONTROLLED BY ANY SWITCH
FIGURE 8089019 6-17-13
GREEN
N
L1
RED
RED
WHITE
BLACK
SWITCH UST BE
RATED TO
5 A PS @ 115 VAC
WIRING
T-STAT
CB14 TE PERATURE OR TI ER SWITCH CONTROLLED
FIGURE 8089021 6-10-13
GREEN
NL1
WHITE
TI ER SWITCH
10 IN
20 IN
30 IN
60 IN
OFF
BLACK
WHITE
GREEN
RED
RED
RED
BLACK
T-STAT
CB14 TE PERATURE OR SWITCH-IT CONTROLLED
FIGURE 8089025 6-13-13
GREEN
RED RED
WHITE
BLACK
N
L1
RE OTE
OFF
ON
RED
S OOTH BLACK
RED
BLACK
RIBBED
ANTENNA
TO OTOR
STRETCHED VIEW
SWITCH-IT
WIRELESS RECEIVER
T-STAT
CB14 SWITCH-IT CONTROLLED
FIGURE 8089024 6-13-13
GREEN
RED
RED
WHITE
BLACK
N
L1
RE OTE
OFF
ON
RED
S OOTH BLACK
RED
BLACK
RIBBED
ANTENNA
TO OTOR
STRETCHED VIEW
SWITCH-IT
WIRELESS RECEIVER
T-STAT
CB14 TE PERATURE AND ANUALLY CONTROLLED
FIGURE 8089023 6-17-13
GREEN
N
L1
WHITE
WALL SWITCH
RED
RED
BLACK
Tabla de contenidos
Otros manuales de Admirador de TJERNLUND
TJERNLUND
TJERNLUND AD-1 FOR WOOD OR COAL STOVES 8504012 REV A... Manual de usuario
TJERNLUND
TJERNLUND SIDESHOT SS2 Manual de usuario
TJERNLUND
TJERNLUND SS1C SIDESHOT WITH UC1 UNIVERSAL CONTROL (VERSION X.02) 8504103 REV... Manual de usuario
TJERNLUND
TJERNLUND SS1 SIDESHOT WITH UC1 UNIVERSAL CONTROL (VERSION X.04) 8504102 REV C... Manual de usuario
TJERNLUND
TJERNLUND UC1 Manual de usuario
TJERNLUND
TJERNLUND HSJ Guía del usuario
TJERNLUND
TJERNLUND AIRESHARE AS2 Manual de usuario
TJERNLUND
TJERNLUND DRAFT INDUCER DJ-3 Manual de usuario
TJERNLUND
TJERNLUND 1 Manual de usuario
TJERNLUND
TJERNLUND SS2 SIDESHOT WITH UC1 UNIVERSAL CONTROL (VERSION X.04) 8504105 REV B... Manual de usuario
TJERNLUND
TJERNLUND WARRANTY POLICY 8500115 Manual de usuario
TJERNLUND
TJERNLUND HS-3C CANADIAN 8504002 REV 2 0997 Manual de usuario
TJERNLUND
TJERNLUND SS1R SIDESHOT (DISCONTINUED VERSION-PRE UC1 UNIVERSAL CONTROL) 8504046 REV... Manual de usuario
TJERNLUND
TJERNLUND SS1C SIDESHOT (DISCONTINUED VERSION-PRE UC1 UNIVERSAL CONTROL) 8504040 REV 4... Manual de usuario
TJERNLUND
TJERNLUND SS1 SIDESHOT WITH UC1 UNIVERSAL CONTROL (VERSION X.06) 8504102 REV D... Manual de usuario
TJERNLUND
TJERNLUND DRAFT INDUCER DJ-3 Manual de usuario
TJERNLUND
TJERNLUND DRAFT INDUCER DJ-3 Manual de usuario
TJERNLUND
TJERNLUND EF DUCT BOOSTER FANS 8504057 REV.793 Manual de usuario
TJERNLUND
TJERNLUND 950-0471 COMMERCIAL PAI FAN PROVER KIT 8504086 REV. A... Manual de usuario
TJERNLUND
TJERNLUND HSJ Manual de usuario
