Titon TP577 Manual de usuario
1
BM886 Iss 02
HRV
Q
Plus
Flared Ducting Cover
Fitting Instructions
The HRV Q Plus Ducting Covers can be used on Titon HRV units that are housed in sheet steel housing (Units HRV10 and
HRV10.25 that are EPP housing cannot be tted with a Duct Cover). Duct Cover are designed to cover the duct work that go from
the unit to the ceiling and are adjustable in height from 300mm to 400mm. The ducting cover increases in area from the top of the unit
so that the area at the ceiling is large enough to accommodate round to rectangular elbows in the ceiling void. There are 4 dierent
ducting covers depending on the unit they are designed for. They are as follows:
TP577 – HRV1.25, 1.35 Flared Ducting Cover
TP588 – HRV1.6 Flared Ducting Cover
TP578 – HRV1.75, 2, 2.85, 3 Flared Ducting Cover
TP579 – HRV10M, 10.25M Flared Ducting Cover
Handling
All lifting must be in accordance with the 89/391/CEE standard (and associated updates), and/or local regulations.
Packing Contents
Inspect the contents in the packaging when taking delivery. Check the parts for damage and that all xings have been supplied
Package supplied with:-
1 x Removable
front panel
2 x Side wall
mounting panels
(L & R handed)
1 x Removable
bottom front panel
2 x Side bottom
panels
(L & R handed)
2
BM886 Iss 02
8 x M5 washers
8 x M5 pan head screws
2 x M5 Square nuts
4 x M6 washers
4 x M6 Nuts
1 x Fitting instructions
Note: All steps are generic for all ducting covers.
1 - Mount the HRV unit
Mount the HRV unit as per the HRV product manual.
Ensure that a gap of 300 to 400mm is maintained between the top of the unit and the ceiling.
THE DUCTING SHOULD NOT BE ATTACHED PRIOR TO THIS INSTALLATION.
2 - Mark and prepare mounting holes
Prepare the mounting surface in the positions specied for six Ø6mm xings.
Leave the duct ports covers in the HRV to prevent any dust entering the unit whilst drilling into surface.
BETWEEN 300 - 400MM
A
CEILING
B
30
80
80
Product
Code A B
TP577 664 596
TP578 755 706
TP579 755 796
TP588 646 600
3
BM886 Iss 02
3 - Assemble side wall mounting panels to side bottom panels
Attach side bottom panel to side wall mounting panel using 4 x M6 washers and 4 x M6 nuts provided.
The side bottom panel is to be at its highest position as shown. This is to be actioned for both left and right panels.
4 - Mount side wall mounting panels
Position side wall mounting panels to the holes produced in Step 2.
Mount the side wall mounting panels using selected M6 xings (Not provided)
5 - Lower bottom extension assembly
Loosen the M6 xings that attach the side bottom panels to the side mounting panels. Let the side bottom panels lower so that the
foam strips on the sheet metal ange comes to rest on the top of the unit. For TP577 the ducting cover is wider than the unit due to
room required for the insulated ducting. For this case the foam strip needs to be pushed up against the side of the unit and the top of
the foam ush with the top of the unit.
Retighten the M6 xings.
TP578, TP579 & TP588 TP577
4
BM886 Iss 02
6 - Fix top ange to ceiling
Mark out the top two holes in the side panel to the ceiling making sure that the sheet metal is ush with the side of the unit for TP578,
TP579 & TP588. For TP577 the foam needs to be pushed up against the side of the unit.
Push the side of the ducting cover away from the unit so that the marked holes is visible. Prepare the surface so that the panel can
xed into position. Fix the top of the side wall mounting panel using selected M6 xings (Not provided).
7 - Connect ducting and commission unit
Connect ducting to unit and commission unit as per the HRV product manual.
8 - Assemble removable front panel to the removable bottom front panel
Attach the removable bottom front panel to the front panel using 2 x M5 pan head screws, 2 x M5 washers and
2 x square nuts provided.
Ensure that the face of the square nut is parallel to the side ange of the removable bottom from panel. Slide two parts apart the
same amount as what was measured in note in Step 6
M
E
A
S
U
R
E
5
BM886 Iss 02
9 - Attach removable front panel assembly
Attach removable front panel at the top xing point of the side wall mounting panel using 2 x M5 pan head screws and 2 x M5
washers provided.
For ne adjustment of the removable front panel, slightly loosen the two middle xings that has the square nuts. Slide the bottom front
panel so that the anges are in contact with the side panels.
Tighten screws when panel is in the desired position.
Attach the bottom front panel to the side bottom panels using 4 x M5 pan head screws and 4 x M5 washers provided.
For future commissioning and to remove front panel of HRV unit then remove the removable front panel assembly.
6
BM886 Iss 02
Use with First Fix Unit TP591
Both TP578 and TP579 can be used in conjunction with HRV Q Plus First Fix unit TP591.
1. Install First Fix Unit TP591.
Install First Fix Unit TP591 as described in product manual BM 887 without connecting the ducting to the unit. If ducting has
already been connected to unit then disconnect.
2. Loosen Side xings in First Fix
Loosen both sets of side xings in First Fix by 2 – 3mm.
3. Attach Side Panel of Ducting Cover
Oer up the side panel of ducting cover to the rst x unit, with the slots in the top ange of the ducting cover lining up with the xings
in the rst x.
Re-tighten the xings in the rst x so that the side panel is secure.
Repeat step with the opposite hand side panel.
Use Step 4 to 9 not including Step 6 to complete the installation.
Este manual sirve para los siguientes modelos
3
Otros manuales de Admirador de Titon
Titon
Titon Solace TP200/RT Manual de usuario
Titon
Titon HRV10.25 Q Plus ECO Manual de usuario
Titon
Titon CME2Q+ Manual del propietario
Titon
Titon TP406HMB Manual de usuario
Titon
Titon CME2 Q Plus LS Manual de usuario
Titon
Titon TP325 Manual de usuario
Titon
Titon TP461BC Manual de usuario
Titon
Titon HRV10 Q Plus Manual de usuario
Titon
Titon CME MEV Manual de usuario
Titon
Titon HRV1.3 Q Plus ECO Manual de usuario
Titon
Titon H200 Manual de usuario
Titon
Titon CME3.1Q+ Manual de usuario
Titon
Titon HRV1.25 QPtus ECO Manual de usuario
Titon
Titon PIV L3 Manual de usuario
Titon
Titon WCME100 Manual de usuario
Titon
Titon TP440MB Manual de usuario
Titon
Titon CME1 Q Plus Manual de usuario
Titon
Titon HRV1.25 Q Plus ECO Manual de usuario
Titon
Titon SF Xtra Vent Series Manual de usuario
Titon
Titon CME1 Manual de usuario
