Tion MagicAir Base Station Manual de usuario
USER MANUAL
Air quality monitor and climatic devices controller
MagicAir Base Station
Model: Tion BS310
2
User Manual
CONTENTS
GENERAL INFORMATION
PACKAGE CONTENTS
SAFETY MEASURES
SPECIFICATIONS
PREPARATION TO OPERATION
ARRANGEMENT AND OPERATING PRINCIPLE
MAINTENANCE
STORAGE, TRANSPORTATION AND DECOMMISSIONING
WARRANTY
1.
2.
3.
4.
5.
6.
7.
8.
9.
3
4
4
6
7
9
15
16
17
3
MagicAir Base Station
Air quality monitor and climatic devices controller MagicAir Base Station, model:
Tion BS310 (hereinafter referred to as base station or device) is a compact device
designed to monitor indoor air quality and control climate equipment.
Basic functions:
• measurement of air parameters (carbon dioxide concentration, humidity
and temperature) using a sensor system;
• collection and transmission of air condition data to a cloud server;
• display of air quality in the operating mode using the light indication;
• automatic control of climatic equipment based on sensor readings and
user settings.
Before using the device, carefully read the User Manual, warranty conditions, and also
check the completeness and appearance.
The device meets the requirements of:
• ТU 4257-004-66248641-2016;
• directive 2014/30/EU EMC;
• directive 2014/35/EU LVD;
• directive 2014/53-EU RED;
• directive 2011/65/EU and amendment directive 2015/863/EU RoHS.
The Certificate of Conformity is available on tion.global/doc.
Developed and manufactured by Tion Smart microclimate, JSC.
112,20, Inzhenernaya st., Novosibirsk, 630090, Russia.
Factory: Tion Smart microclimate, JSC 112, 20 Inzhenernaya st., 630090,
Novosibirsk, Russia
tion.global
1. GENERAL INFORMATION
Dear Customer!
Thank you for purchasing Air quality monitor and climatic devices controller Mag-
icAir Base Station, model: Tion BS310! This manual contains full information about
the device, adjustment procedures and maintenance rules.
4
User Manual
The full package contents are shown in Table 2.1.
The following notations are used in this User Manual:
Table 2.1 — Package contents
2. PACKAGE CONTENTS
3. SAFETY MEASURES
List of items and accessories Quantity, pcs
Device 1
Power supply unit 100–240 V~, 50/60 Hz 1
Quick Start Guide 1
Warranty card 1
DANGER! Requirements, non-observance of which may result
in failure of the device or dangerous conditions for health and life.
CAUTION! Requirements, non-observance of which may result
in failure of the device or dangerous conditions for health and life.
The device is not intended for use by children and people with special
physical, sensory or mental development, except when the operation is
carried out under the control of persons responsible for their safety.
Do not leave the power cord in the reach of children or pets, even when the
device is turned off.
Do not repair or modernize design of the base station. If you find any
damage or signs of abnormal operation, contact the service organization
of the seller for advice on the possibility of further operation of the device.
Do not operate the device if the insulation of the power cord or the parts
is damaged.
Do not use power supplies with an output voltage exceeding value
indicated on power unit included into scope of supply. Excessive voltage
or current supply to the base station can lead to a fire hazard.
To prevent fire or electric shock, do not expose the device to atmospheric
precipitation, vapors and liquids, open flames or direct heat radiation from
heating devices.
5
MagicAir Base Station
The device is intended for use at temperatures from 0 to +45 °C, relative
humidity from 0 to 95% and for storage at temperatures from -20 to +45 °C.
Do not cover or subject the base station to shock: this may lead to
incorrect measurements of air parameters and damage to the device.
Do not connect the device to power using the USB port of a personal
computer: this can result in unstable operation of the base station.
Do not install the base station in places where animals and humans are
permanently located: near a computer, on a desktop, or in a recreation
area. This can lead to excessively high readings of the device of carbon
dioxide concentrations an increase in the load on controlled climate
devices.
It is necessary to turn off and disconnect the device from the power
supply during a thunderstorm.
The device is designed for indoor use only. Do not use it in rooms
with sources of water and steam: pools, baths, saunas, bathrooms or
sanitary rooms.
6
User Manual
Specifications of base station are shown in Table 4.1
Table 4.1 — Specifications
4. SPECIFICATIONS
Parameter Value
Overall dimensions (H×W×D) 100×100×27 mm
Weight (net) (133±3) g
Power voltage (5±0,1) V
Current consumption NMT 1 А
Concentration of carbon dioxide measurement range 0–5000 ppm1
Concentration of carbon dioxide measurement accuracy ±(50 ppm + 5% of measured
value)
Temperature measurement range 0–45 °С
Temperature measurement accuracy ±1,5 °С
Relative humidity measurement range 0–95% (free of condensate
formation)
Relative humidity measurement accuracy2±4%
Compatibility with Wi-Fi Wireless Technology Standards IEEE 802.11b/g/n (only 2,4
GHz)
Compatibility with Bluetooth Wireless Technology Standards IEEE 802.15.1 (Bluetooth
4.0–4.2, 5.0 Low Energy)
Control of devices within the system IEEE 802.15.1 (Bluetooth 4.2
Low Energy) — up to 8 devices
TIONMA-868 (proprietory
protocol for RF channel 868
MHz) — up to 32 devices3
RF-module frequency band 868.8-869.1 MHz
RF-module maximum ERP 25 mW
BLE-module frequency band 2400–2483 MHz
BLE-module maximum EIRP 2.5 mW
Wi-Fi-module frequency band 2400–2484 MHz
Wi-Fi-module maximum EIRP 100 mW
Warranty operating life 1 year
Lifetime 10 years
1ppm (parts per million) — is measurement unit for carbon dioxide concentration.
2 Measurement accuracy is indicated in absolute values (%). For example, at relative humidity of 80%, the actual
humidity is in the range of 76–84% or (80 ± 4)%.
3A maximum of 32 devices can be connected to one base station. No more than 8 devices can be controlled by
BLE technology (IR Module MagicAir and Danfoss Eco smart radiator thermostat).
7
MagicAir Base Station
5.1 Unpacking and pre-examination
Remove the device from the packaging bag, carefully inspect it and make sure that
there is no damage. Possible defects include the following: scratches, chips, uneven
color of plastic on the device’s case, as well as similar damage to the power supply unit
and violation of the integrity of the USB cable. If you find any defects, ask the supplier
to provide written confirmation of the damage.
If the device has been stored or transported at an air temperature below +10 °C, let it
stay in the packaging bag in the room for 2 hours to warm it to the room temperature.
It is required for eliminating condensation, damage of plastic parts while assembling
and malfunction of the device.
5.2 Installation
The device is designed for indoor use only. When choosing place of installation, make
sure that all the safety requirements specified in section 3 of this User Manual are met.
The device can be located on any horizontal surface or on a wall. Eyelet designed for
hanging on the bottom side is used for this purpose.
Base station should be protected from exposure to liquids, steam or other abundant
moisture. Do not place the device in bathrooms or sanitary rooms. Do not use the
device in the immediate vicinity of a cooking place or humidifier.
Do not install near any heat sources such as radiators, heaters, or stoves. Do not
place the base station near radiators of household appliances (for example, acoustic
devices, refrigerators, etc.).
Place USB-cable so that it does not twist, jam or bend excessively. Do not leave it in
places accessible for children or pets.
5.3 Set up
To ensure operation of Smart Microclimate Control System MagicAir, you should first
connect the base station on MagicAir mobile application.
The application is developed for mobile devices based on iOS (10.0 and later) and
Android (4.4 and later) operating systems. For installation, it is necessary to have
smartphone, which ensures access to the Internet. The application is available free at
and .
Choose any way to install the application:
5. PREPARATION TO OPERATION
8
User Manual
1. Scan the QR code below to proceed with downloading the application.
Then click Install.
2.Follow the direct link on your smartphone:
https://play.google.com/store/apps/details?id=com.tion.magicair
https://apps.apple.com/us/app/magicair/id1111104830
After installing and running the application, you must register and create an account.
Enter your account information: email and password. The system will send a letter
to the specified address with a link to confirm personal data. After clicking on it,
registration will be completed.
Re-enter the application and follow the step-by-step instructions to configure the base
station.
Connection to one base station results in creation of one home. This is a virtual
space where you plan to place climatic devices and collect microclimate data. Home
combines the neighboring rooms (rooms) in which the devices are located.
A maximum of 32 devices can be connected to one base station.
No more than 8 devices can be controlled by BLE technology. You
can add up to 12 rooms in one home. You can create a maximum of
20 homes on one account.
9
MagicAir Base Station
6. ARRANGEMENT AND OPERATING PRINCIPLE
6.1 Arrangement
Base station is a solid block (Fig. 6.1, p. 1), which contains the following:
• sensors (temperature, humidity, concentration of carbon dioxide);
• microprocessor;
• Wi-Fi module;
• block of BLE-module and RF channel for connection with climatic devices;
• light indicating system.
The light indication (Fig. 6.1, p. 2) helps to evaluate the state of connection to the
MagicAir system and the level of CO2concentration in the room.
The brightness of the light indication is automatically adjusted
depending on the illumination of the room. In the daytime, the
brightness level is maximum, and at night it is minimal. You can
turn off the light indication only in the MagicAir application in the
settings of the base station.
The device is equipped with a built-in power cable (Fig. 6.1, p. 3) with a standard USB-A
output. Power supply unit (Fig. 6.1, p. 4), which is included in the delivery package, is
used to connect the base station to a power supply network of 230 V, 50 Hz.
Figure 6.1 — Base station kit
1 — base station (front side); 2 — light indication; 3 — power cable;
4 — power supply unit.
10
User Manual
Figure 6.2 — The bottom side of the base station
1 — setup data; 2 — serial number; 3 — “Reset” button; 4 — “Mode” button.
Necessary information for setup and diagnostics is located on the bottom side of the
base station. Wi-Fi data, Wi-Fi MAC and MAC address of the base station are presented
in the lower left corner (Fig. 6.2, p. 1). Wi-Fi data may be required when connecting the
device to MagicAir system. Wi-Fi MAC is for setting-up on the local network and the
MAC address is for remote diagnostics, carried out by service division.
When contacting an authorized service center or service organization
of the seller, please be ready to tell serial number of the device. It is
located on the bottom side of the base station (Fig. 6.2, p. 2).
“Mode” button (Fig. 6.2, p. 4) is used to activate the base station when connecting to
the MagicAir system, to replace one device with another, or to update Wi-Fi settings via
MagicAir application. Press “Reset” button to return to default settings (Fig. 6.2, p. 3).
6.2 Operating principle
The base station is the center of the Smart Microclimate Control System MagicAir,
to which other devices are connected within accessible radius (Fig. 6.3). It measures
the concentration of CO2, temperature and humidity in the room by means of sensors.
Then the data are transferred to cloud server, where information about the state of the
microclimate in the room and controlled devices is processed and stored.
The devices (breezer, air purifier, infrared module and conditioner
etc.) can be controlled via the MagicAir system after they are
connected to the base station.
Using MagicAir mobile application you can monitor and control microclimate anytime
from anywhere in the world via the Internet.
Este manual sirve para los siguientes modelos
1
Tabla de contenidos
