Timeguard LEDCST10PIRB Manual
Installation & Operating Instructions
1
LED Coastal Grade
PIR Floodlight
Model: LEDCST10PIRB (Black)
Model: LEDCST10PIRWH (White)
Model: LEDCST20PIRB (Black)
Model: LEDCST20PIRWH (White)
Model: LEDCST30PIRB (Black)
Model: LEDCST30PIRWH (White)
1 2
1. General Information
These instructions should be read carefully and retained for further reference
and maintenance.
2. Safety
• Before installation or maintenance, ensure the mains supply to the luminaire
is switched off and the circuit supply fuses are removed or the circuit breaker
turned off.
• It is recommended that a qualified electrician is consulted or used for
the installation of this luminaire and install in accordance with the
current IEE wiring and Building Regulations.
• Check that the total load on the circuit including when this luminaire is fitted
does not exceed the rating of the circuit cable, fuse or circuit breaker.
3. Technical Specifications
• 230V AC, 50Hz
• These luminaires are of class I construction and must be earthed
• Energy Efficiency: Class A
• Colour Temperature: 4000K
• IP55 Rated suitable for restricted external applications
• Detection Angle: 180°
• Detection Range: Up to 12 metres
• Time On Adjustment: 5 seconds to 10 minutes
• Dusk Level Adjustment: Day and Night or Night only operation
• CE Approved
LEDCST10PIRB-WH
• 10W LED Non replaceable lamp
• Energy Usage: 10Kwh/1000h
• Lumen Output: 750lm
LEDCST20PIRB-WH
• 20W LED Non replaceable lamp
• Energy Usage: 20Kwh/1000h
• Lumen Output: 1500lm
2 3
Other Loads – External (Slave)
• Up to 10 sets of LEDCST10-20-30 Uncontrolled floodlights
• LED lamp: Max 10 sets with total of 200W
• Halogen lamp: Max 1000W
• Fluorescent: Max 15 sets 23W, or Max 345W
• Fluorescent tube w/o PF correction: Max 648W
Parallel Switching
• A maximum of 4 LEDCST10-20-30PIR floodlights can be wired in parallel
to enable any detector to turn ON all the lights connected.
4. Installation Advice
As the detector responds to changes in temperature, avoid the following situations:
• Pointing the detector towards objects with highly reflective surfaces,
such as pools of water or white-painted walls.
• Mounting the detector near heat sources, such as heating vents,
air conditioning units, lights etc.
• Pointing the detector towards objects that may move in the wind,
such as curtains, tall plants etc.
LEDCST30PIRB-WH
• 30W LED Non replaceable lamp
• Energy Usage: 30Kwh/1000h
• Lumen Output: 2250lm
up to 12m
3m
180°
3m
2.5m
12m
12m
up to 12m
3m
180°
3m
2.5m
12m
12m
3 4
• Recommended installation height is 2.5m above ground, the maximum
detection range about 12m and at the angle of about 180°.
5. Installation Procedure
5.1 Mark the position of the mounting holes
on the wall using the U bracket supplied
as a template.
5.2 Drill the holes for the wall plugs ensuring
not to infringe with any gas/water pipes
or electrical cables that may be hidden
below the surface.
5.3 Fix the U bracket to the wall using
the correct screws for the wall
plugs installed.
4
5.5 Attach the strain relief to the luminaire
and screw in ensuring not to over-tighten.
5.6 Terminate the supply cable into the terminal
block (please refer to section 6 connection
diagram) ensuring correct polarity is observed
and that all bare conductors are sleeved.
5.7 Attach the supplied wall plate to the
luminaire, apply pressure to catches located
on top and bottom until all click into place to
ensure the weatherproof seal.
5.8 Attach the luminaire to the U bracket
fitted to the wall, then screw in on both
sides ensuring not to over-tighten.
5.4 Secure the supply cable into
the junction box through the
hole(s) provided ensuring that a
cable gland, grommet or sealing
compound is used to maintain
the IP rating of the luminaire.
MAINS
SUPPL
Y
L
N
E
ISOLATION
SWITCH
LLN
1
5 6
Connect the 3 core mains supply cable to the terminal block on the unit as follows:-
LIVE (Brown or Red) L
NEUTRAL (Blue or Black) N
EARTH (Green/Yellow)
Connect the 3 core mains supply cable to the terminal block on the unit as follows:-
LIVE (Brown or Red) L1
NEUTRAL (Blue or Black) N
EARTH (Green/Yellow)
6. Connection Diagram
For additional lighting connect the external load
to the terminal box on the back plate as follows;
6
7. Operation
• Turn the power on to the isolating switch and test for correct operation.
8. Walk Test and Adjustment
• The purpose of the Walk is used to test and adjust the detection coverage
of the floodlight under auto mode.
Test Procedure
• Adjust the Time knob to (fully anti-clockwise), and Lux knob
(can be set to ‘Sun’ or ‘Moon’).
• Switch the power On.
• Walk across the detection area, once to detector is triggered the lamp
will turn ON for 2 seconds.
Note walking direction when performing test.
Detector Head Adjustment
• The detector head can be turned 90°
left or right by hand, and can be
tilted 90° downward.
• Do not use the adjuster knobs
to turn the detector head.
7 8
HELPLINE
020 8450 0515
Knob Settings
The floodlight has two adjustment knobs:
Time and Lux at the bottom of the detector head.
• Adjust the knobs carefully with flat blade screwdriver.
TIME knob setting
• You can set the time knob from 5 seconds to about 10 minutes,
the floodlight will switch the lamp ON, for the time
duration set after each detected movement.
• Adjust the knob as desired.
LUX knob setting
• When setting the Lux knob at ‘MOON’, the floodlight
will only operate in the dark.
• When setting the Lux knob at ‘SUN’, the floodlight
will operate in any light level.
Setting Advice
WARNING
8 9
Dusk setting (Time knob setting)
• When setting the Time knob to fully clock wise, the motion detector
of the floodlight won’t function.
The lamp will operate depending on the ‘Lux’ level, i.e. dusk to dawn.
9. Lens Masking
• The purpose of the
lens mask is to mask
out areas not desired
for detection.
Masking the Sensor Lens
• To restrict the sensor coverage, preventing detection in unwanted areas,
mask the sensor lens using the masking label provided. The top section of
the lens covers long range detection, the bottom covers short range.
Similarly the left and right lens sections cover the left and right
detection areas respectively.
910
10. Manual Override Mode
The light can be switched on for longer time periods by use of the
Manual Override Mode. This can be activated at night by using
the internal wall switch or circuit breaker.
• Switch the internal wall switch/circuit breaker once (OFF/ON)
within 1.5 seconds
• The unit will now illuminate continuously until dawn, or until switched
back into Auto Mode
• To switch the unit back into Auto Mode, switch the internal wall switch/circuit
breaker once (OFF/ON) within 1.5 seconds.The unit will operate as set up
after the walk test procedure
• Note: The Manual Override Mode will not work if the floodlight is set
into Test Mode (i.e. the Time Knob set fully clockwise)
11. Lamp Adjustment
• The lamp can be tilted upwards 45° and tilted downwards 60°.
Este manual sirve para los siguientes modelos
5
Tabla de contenidos
Otros manuales de Foco de Timeguard
Timeguard
Timeguard LED88PIR Manual
Timeguard
Timeguard MLB500C Manual de usuario
Timeguard
Timeguard LED200PIRBE Manual
Timeguard
Timeguard LEDPRO70B Manual
Timeguard
Timeguard LEDSF10B Manual de usuario
Timeguard
Timeguard ECO Series Manual
Timeguard
Timeguard LEDPRO10WH Instrucciones de instalación
Timeguard
Timeguard LEDX10PIRB Manual
Timeguard
Timeguard ECO42F Manual de usuario
Timeguard
Timeguard LEDX30PIRWH Manual
Timeguard
Timeguard LEDX20PIRBN Manual
Timeguard
Timeguard MLW3000 Manual
Timeguard
Timeguard MLB98 Manual
Timeguard
Timeguard LED100PIRBE Manual
Timeguard
Timeguard ECO36F Manual de usuario
Timeguard
Timeguard NCFB150C Manual de usuario
Timeguard
Timeguard Sure time STFL10PIRB Manual
Timeguard
Timeguard LED100PIRBP Manual
Timeguard
Timeguard LEDX10PIRWH Manual
Timeguard
Timeguard LEDX10PIR Manual
