TILLYTEC MAXI UNI Manual de usuario

-1-

User manual Maxi uni / Mini uni

Safety Advice

 Before using the torch, ensure that you read and understand the safety advice leaflet so that the torch is

always operated correctly.

 Never point the light beam at your or other persons eyes. Doing so could damage the retina.

 Keep the torch away from children.

 Never attempt to take the torch apart unless it is specifically directed in the operating instructions. Doing so

can result in severe in uries and electric shocks. Servicing of internal components, servicing or repairs have

to be carried out by qualified persons, authorized by the manufacturer.

 If smoke or steam appears, switch off the mains or battery supply immediately. Disconnect the torch head

from the battery and remove the charger from the socket.

 Do not touch the charger’s power cable with wet hands as there is danger of an electric shock or short

circuit. To disconnect, depress the catch on the connector whilst withdrawing it from the charging adapter

plug. Do not disconnect it by pulling on the cable.

 To prevent overheating, damage, fires, electric shocks or other dangers only use the charger and

attachments supplied.

 Keep the torch and battery pack away from open fires or sources of heat as it could lead to overheating,

fires, electric shocks and explosions and cause severe in ury.

 Never attempt to change or take apart the battery pack. To do so could lead to in ury by explosion.

 Do not drop the batteries or battery packs and protect them from impact. Damage could result in leakage of

the battery chemicals and result in in uries.

 Clean with water all areas of the body (especially mouth and eyes) or clothing that come in contact with

battery chemicals.

 Never short across the battery contacts with metal ob ects (e.g. key rings, screwdrivers etc) as this could

result in overheating and to burns and other in uries.

 After charging disconnect the charger from the battery pack and the mains socket to avoid fires or other

damage.

 The charger supplied with the torch has been developed for use exclusively with the torch and battery pack.

Do not use it with other products or batteries as this could result in fires or damage.

 Use and store the torch, battery pack and charger away from exposure from heavy solar radiation or high

temperature (e.g. the dashboard or the boot of a car etc.). Heavy solar radiation and heat can lead to

leakage, overheating or explosion of the batteries which can result in fire other damage.

 While charging the battery pack keep it in a well ventilated area.

 Charge the battery pack at room temperature.

 If the batteries become too warm, cease charging immediately. Normal temperature is slightly higher than

“hand-hot“ ( +/- 50 degree )

 Let the batteries cool down after charging.

 Use the torch, battery pack and accessories only when diving. Using the products or other component parts

for other purposes is not allowed.

-2-

Maxi uni

General Care and Usage Instructions

 The O-rings (sealing rings) should only be removed if they require replacing.

 Lubricate the O-rings occasionally with a smear of silicone grease. Please do not apply

to much grease. Do not use silicone spray !

 Regularly inspect the O-rings for damage or contamination, and change them if

necessary. We recommend that you carry spare O-rings.

 The torches can be operated out of water for a short time, however they will become

very hot very quickly so do not leave unattended. Only operate until the torch head

becomes warm.

 After use rinse the torch thoroughly with fresh water whilst still attached to the umbilical

and battery pack. Never use any other cleaning agents.

 Do not shine the torch into your eyes or the eyes of others as severe damage to the

retina could result.

 When transporting the torch, make sure, that the first O-ring on the battery tube is

visible. Turn the lamp head out until you see the first O-ring during the transport.

PLEASE OTICE THE VIDEOS FOR GREASI G THE O-RI GS O THE

HOMEPAGE OF TILLYTEC OR O OUR YOUTUBE CHA AL !

Advice on Using Battery Chargers

 Possible non rechargeable and rechargeable batteries:

- 3 x AAA alkaline batteries in a battery holder (optional *)

- 3 x AAA NiMh battery in a battery holder (optional *)

- 1 x 18650 accumulator with mit space holder (optional *)

- 1 x 26650 accumulator

- 2 x 26650 accumulator in the long battery tube and battery holder (long battery

tube and battery holder optional*)

- 1 x 21700 accumulator

- 3 x 21700 accumulator in the battery tube short compact (battery tube short

compact optional*)

 For the cell 18650 / 26650 / 21700 we recommend only to use batteries from type

LiCoMn / LiCo i (lithium – cobalt – mangan / lithium – cobalt - nickel). Otherwise

there is danger for explosion !

available only at TillyTec

All mentioned batterys and suitable charger are available at shop www.tillytec.de

at register tools !

-3-

Maxi uni

otes on the use of mechanical dimming

The mechanical dimming does not work as a electronics, it works with a spring. Switch on the

dimming as follows:

 Screw in the battery tube short completely = light power 100 %

 Screw the battery tube short few millimeters in the direction of „OFF“ = light power is

dimmed

 Screw battery tube short further in the direction „OFF“ = the light is off

As long as the battery tube is turned, the light is flickering. This is normal and owed to the

mechanics.

If the battery tube is not turned, the light no longer flickers.

If the light flickers even in the position, when the torch is completely on, clean first the silver border

of the battery tube short. Over time of using the torch deposits (grease rests etc.) can place here,

which must be removed. Please also note that the contacts on the LED module are kept clean.

Which one LED module is used ?

Usually there is no optical recognition of which LED module is installed.

Thats why you should read the following hints :

The LED module is marked on the back of the LED board.

Unscrew the short battery tube or the battery tube short compact or the umbilical from the lamp

head.

Then look into the open lamp head from behind.

There are 4 coloured dots, always starting with white.

So the first white dot plus 3 additional coloured dots.

This results in a colour code.

The colour code you find under www.TillyTec.de in the downloadcenter under :

INFORMATION

User manuals / possible components

Possible – components view / download

Find the appropriate colour code from the table. You will see here the name of the LED module, as

well as the possible configurations with batteries and rechargeable batteries, as well as the

corresponding burning times.

-4-

Maxi uni

otes for using of charger

 The hints of the operating instructions of the manufacturer are to be observed.

 The charger has several LED lamps that indicate the progress of the battery charge.

 The charger can connected to the battery verytime. You do not have to discharge

the battery !

IMPORTA T: Use chargers only indoor or in dry rooms. The voltage values and

settings must be respected.

Burn time and light power



The burn time and the light power of the torch depends on

- the used LED modul

- the used type of battery or accumulator.

TIP : When the LED module of the MAXI uni is not bright enough

we will send a stronger LED module for trial for free.

 More information about burning time and light power you will find on www.TillyTec.de –

on register „information“.

Operation and Handling / Changing the LED moduls

 To turn your torch on and off, rotate the torch head. A half rotation is sufficient to

engage the contacts. Further rotation when switching off is not a problem as the

system is protected with 3 O-rings, however it should be stopped when the first O-ring

is visible.

 How to change the LED modul you can see on the website www.TillyTec.de or at the

TillyTec youtube channal. Please have a look !

IMPORTA T : Tighten the space holder very strong by hand. Otherwise the cooling of

the LED module is not enough. So the LED module will be destroyed immediately !

 The space holder is hand tightened to press the LED module against the glass. This is

necessary so that the LED module can be cooled well. Without cooling the LED module

is destroyed ! The space holder should be clean and free of grease on the flat side,

where the LED module lies cloosly for cooling (cooling paste may be used).If you use a

version where the LED module is screw on the pace holder with socket screws, please

screw the LED – module tightly tot he space holder.

Videos, which explain the change of the LED modules, can be found on the homepage of

TillyTec (www.TillyTec.de) or on our own Youtube channel. PLEASE LOOK THEESE

VIDEOS !!!

-5-

Maxi uni

 After the space holder is screwed hand tight, the battery tube is screwed together with

the battery in the lamp head to see if the torch is working.

Screw the battery tube only

slightly ! not strong ! Screw it only until the torch is on. Repeat the turning on and off

several times and watch the LED module . But never look directly into it ! When

switching on and off the LED module should not or only very little rotate (only a few

millimeters). If the LED module rotates to much the space holder is too loose.

 Please check the space holder every 15 to 20 dives and if it is nessesary please

screw it a little bit stronger !

IMPORTA T !

To ensure the tightness of the torch please grease the parts as following is

shown regulary:

 The three O-rings on the lamp head ( 1 ) are only visible, when the torch is opened to

change the LED Module. In this case please grease always these O-rings !

 The tread of the space holder ( 2 ) inside please grease all 10 - 20 dives . This do only

in the range of 10 - 15 mm from the beginning of the hexagon . The tread of the spacer

( 2 ) outside

always grease when the LED module is changed .

 The three O-rings in the protective ring (3) are only visible when the space holder (2) is

completed removed. When the LED Module will changed always grease the three O-

rings.

 The three O-rings on the battery tube ( 4 ) are always visible, when the battery tube is

unscrewed This must be greased at least every 10-20 dives regularly or whenever the

lamp is not used for a long time ( approximately 3 months ) .

GREASE MEA S :

It is to see a glossy film - it is not swimming in grease !

Here again the hint to our videos on www.TillyTec.de or on the youtube channel !

Battery tube (4

)

otective ring

(3)

space holder

(2)

light head

(1)

-5-

-6-

Maxi uni

Maxi uni / Mini uni

Goodman hard heavy duty

The Goodman can be ad usted

very quickly in height and hand

size by loosening the ad usting

screw and moving the Goodman's

plate.

Here it can also be rotated

completely for transport and

protection of the lamp head.

The Goodman can also be

ad usted in size by

loosening and sliding the

llen screw

The hose supplied can be

mounted around the lamp

head/battery tube of the

Maxi uni. This means that

the Goodman's clamp sits

more firmly at the lamp

head / battery tube and the

lamp head / battery tube

does not spin when the

lamp is switched on.

-7-

The Goodman hard heavy

duty offers the possibility to

use different combinations of

the Maxi uni and Mini uni at

the same time. The battery

tube short compact can also

be used instead of the maxi

uni.

Maxi uni / Mini uni

Goodman hard heavy duty

adapter

The following combinations are possible:

- 1 x Maxi uni / battery tube short compact

- 1 x Maxi uni / battery tube short compact + 1 x Mini uni

- 1 x Mini uni

- 2 x Mini uni

- 3 x Mini uni

For use the Mini uni S3, the red adapter ring must ALWAYS be

installed. Before mounting on the Goodman hard heavy duty, we

recommend first mounting the adapter ring on the Mini uni S3.

-8-

IMPORTA T !!!

The clamp of the Goodman hard heavy duty MUST be flush with the

battery tube short compact.

If the clamp is not mounted in this way, the battery tube short compact

will be LEAKI G !!!!

The same applies to your own attachments that are mounted around the

battery tube short compact (for example your own clamps, stainless steel

clamps an so on)

Fastenings in the rear area of the battery tube are also not

permitted and lead to leaks!

-9-

Goodman hard

heavy duty

–

important hints for the

using of battery tube short compact

Maxi uni

-10-

Otros manuales para MAXI UNI

Este manual sirve para los siguientes modelos

Manuales populares de Equipo de iluminación de otras marcas

Brizo

Brizo 8SP-MU-4 Manual de usuario

LUCE&LIGHT

LUCE&LIGHT BROM 1.0 Manual de usuario

IKEA

IKEA BJÖRKSPIREA Manual de usuario

Laserworld

Laserworld Evolution Series ES-400RGB Manual de usuario

Alien

Alien RG STAR Manual de usuario

EuroLite

EuroLite LED B-40 Manual de usuario

Qazqa

Qazqa Suplux SL 3 Black 103062 Manual de usuario

Commercial Electric

Commercial Electric 54568141 Manual de usuario

CREE LIGHTING

CREE LIGHTING 304 Series Manual de usuario

Goobay

Goobay 49867 Manual de usuario

ECOMAN ITALIA

ECOMAN ITALIA LED T8 Manual de usuario

Alkalite

Alkalite Krypton KT-81 Manual de usuario

Clas Ohlson

Clas Ohlson GU10 Manual de usuario

DTS

DTS DELTA 10 F Manual de usuario

ring

ring Solar Steplight Manual de usuario

One Stop Gardens

One Stop Gardens 57696 Instrucciones de montaje

Chauvet DJ

Chauvet DJ COREpar UV120 ILS Manual de usuario

SIREM

SIREM Swimeo A2 Manual de usuario