TiePie TP-EMI-HS6 Manual de usuario

EMI probe set TP-EMI-HS6

The EMI probe set TP-EMI-HS6 is a complete set of probes, conveniently packed

in a carry case. Together with the Handyscope HS6-1000, Handyscope HS6 DIFF-

1000, WiFiScope WS6-1000 or WiFiScope WS6 DIFF-1000 with option E installed,

it turns your instrument into an EMI pre compliance tester.

The set contains three diﬀerently sized H ﬁeld probes and an E ﬁeld probe. To con-

nect the probes to the scope, a short semi ﬂexible antenna cable and a long ﬂexible

antenna cable are included. For proper grounding and termination, a grounded

50 Ohm terminator is also included. The tripod allows exact positioning of the

probe near the test subject.

EMI probe set TP-EMI-HS6 1

Set contents

The EMI probe set TP-EMI-HS6 contains the following items:

TP-NFP-25 H ﬁeld probe

25 mm diameter, female SMA connector

TP-NFP-15 H ﬁeld probe

15 mm diameter, female SMA connector

TP-NFP-5 H ﬁeld probe

9 mm diameter, female SMA connector

TP-NFP-E9 E ﬁeld probe

2 mm tip, female SMA connector

TP-3P-15 tripod

up to 18 cm high

Antenna cable TP-BNC-SMA-200

ﬂexible, 200 cm long, female SMA connector to BNC connector

Antenna cable TP-SMA-20

semi ﬂexible, 20 cm long, male SMA connector to male SMA

connector

Grounded 50 Ohm BNC terminator TP-BNC-T50G

BNC to BNC, 5 cm ground lead with 2 mm banana plug

TP-Wrench89 wrench

8 and 9 mm hex nut wrench

2EMI probe set TP-EMI-HS6

Connecting the probes

To connect a probe to the instrument with option E, ﬁrst place the TP-BNC-T50G

grounded terminator at the Ch1 input of the scope. When using a Handyscope

HS6 DIFF-1000 or WiFiScope WS6 DIFF-1000, make sure to connect the extra

ground lead to the grounding terminal next to the Ch1 input. When using a Handy-

scope HS6-1000 or WiFiScope WS6-1000, the extra ground lead is not required

and can be left unconnected.

Next connect the BNC connector of the TP-BNC-SMA-200 ﬂexible antenna cable to

the grounded terminator. Insert the female SMA connector of the TP-BNC-SMA-

200 through the ring of the TP-3P-15 tripod, from the side with the recessed hex

shape.

Connect the male SMA connector of one end of the TP-SMA-20 semi ﬂexible an-

tenana cable to the ﬂexible antenna cable. Use the supplied 8 mm wrench to

tighten the nut to avoid the semi ﬂexible cable to rotate. Do not over tighten,

maximum torque is 0.3 - 0.6 Nm (3 - 5 in lbf). Finally, connect the required probe

to the other end of the semi ﬂexible antenna cable. Using the semi ﬂexible cable

and the tripod, the probe can be positioned at the exact location near the test

subject.

EMI probe set TP-EMI-HS6 3

In the Multi Channel software, select an EMI Quick Setup to setup the instrument

and software properly for performing the EMI pre compliance test measurements.

Please note that when using the Handyscope HS6 DIFF-1000 or WiFiScope WS6

DIFF-1000, the EMI Quick Setups enable SafeGround for Channel 1, in order to

measure single ended. However, due to the extra grounding connection, the

SafeGround protection feature for channel 1 will be disabled, so there will be no

protection against short circuits to ground on channel 1. For the other channels,

the SafeGround protection remains available.

TiePie engineering

Koperslagersstraat 37

8601 WL Sneek

The Netherlands

Tel.: +31 515 415 416

Fax: +31 515 418 819

E-mail: [email protected]

www.tiepie.com

This information is subject to change without notice.

4EMI probe set TP-EMI-HS6

Tabla de contenidos

Otros manuales de Equipo de prueba de TiePie

TiePie

TiePie Handyscope HS5 series Manual de usuario

TiePie

TiePie WiFiScope WS6 Manual de usuario

TiePie

TiePie Handyscope HS4 Manual de usuario

TiePie

TiePie Handyscope HS5 series Manual de usuario

TiePie

TiePie Handyscope HS4 Manual de usuario

TiePie

TiePie WiFiScope WS6 Manual de usuario

TiePie

TiePie Handyscope HS6 DIFF Series Manual de usuario

TiePie

TiePie Handyscope TP450 Manual de usuario

TiePie

TiePie GMTO ATS5004D Manual de usuario

TiePie

TiePie Handyscope TP450 Manual de usuario

TiePie

TiePie Handyprobe HP3 Manual de usuario

TiePie

TiePie TP112 Manual de operación y mantenimiento

TiePie

TiePie Handyscope HS3 Manual de usuario

Manuales populares de Equipo de prueba de otras marcas

SMART

SMART KANAAD SBT XTREME 3G Series Manual de usuario

Agilent Technologies

Agilent Technologies BERT Serial Manual de usuario

Agilent Technologies

Agilent Technologies N3280A Manual de usuario

Vernier

Vernier Go Direct Voltage Manual de usuario

Lifeloc

Lifeloc R.A.D.A.R. Manual de usuario

Fluke

Fluke T5-600 Instrucciones de funcionamiento e instalación

Mercury

Mercury TSL01 Manual de usuario

MAHA

MAHA MBT Series Manual de usuario

Fuji Electric

Fuji Electric P-61 Manual de usuario

ETC

ETC SealerAtor Manual de usuario

Skyfine

Skyfine ETHYWAY V2 Manual de usuario

Appion

Appion G5 Twin Manual de usuario

PCB Piezotronics

PCB Piezotronics 8159-0112A Manual de usuario

BW Technologies

BW Technologies MicroDock II Manual de usuario

Sun Nuclear

Sun Nuclear 1027 Manual de usuario

Biomark

Biomark HPR LITE READER Manual de usuario

Hioki

Hioki 3169-20 Manual de usuario

Ashcroft

Ashcroft ATE-100 Manual de usuario