TiEmme 2WAYS2 Manual de usuario

Pag. 1 / 9DMAN63W0000020-2Ways2 Manual - System100 Hydro STD2

Revision Date: 11/12/2017

2WAYS2 RADIO

CONTROL FOR

SYSTEM100 HYDRO

STD2 TECHNICAL

MANUAL

Pag. 2 / 9DMAN63W0000020-2Ways2 Manual - System100 Hydro STD2

SUMMARY:

1INTRODUCTION ....................................................................................................... 3

2CONTROL PANEL ...................................................................................................... 4

2.1 THE KEYS ................................................................................................................... 4

2.2 THE DISPLAY ............................................................................................................... 4

3THE MENU ................................................................................................................ 5

3.1 MAIN THERMOSTAT MODIFICATION ................................................................................... 6

3.2 USER MENU................................................................................................................. 6

3.2.1 Chrono Menu........................................................................................................8

3.2.1.1.

Chrono Modality .............................................................................................8

3.2.1.2.

Chrono Programming ......................................................................................8

Pag. 3 / 9DMAN63W0000020-2Ways2 Manual - System100 Hydro STD2

1Introduction

The Radio remote-control manages the functioning of the stove/boiler and monitors the state of operation in

real time. The main characteristics are:

Remote Control of the system with battery supply

Room Thermostat embedded

Parameters management of the control board

Warnings:

The system works on the radio band ISM 433,92MHz. The transmission and receiving distance can be

reduced in case of a noisy environment: other devices as wireless headphones, video sender, toys or other

devices could influence in the performances of the system.

Check the presence of such instruments and make sure to turn them off in order to avoid electromagnetic

waves pollution.

If more remote controls are nearby, it is necessary to associate the remote control with a specific

stove/boiler (see section 3, Settings Menu).

Pag. 4 / 9DMAN63W0000020-2Ways2 Manual - System100 Hydro STD2

2Control Panel

2.1 The Keys

Key

Function

Description

On/Off

Ignition and Extinguishing of the boiler/stove by pushing the button for

3 seconds

Unlock

System Unlock by pushing the key for 3 seconds

ESC

Esc

Menu exit function

SET

Set

Enter in Submenu, modify and save data

Thermostat Modify

Radio Room Thermostat modification

Scroll Menu and

Submenu

Scroll Submenu and Menu

Sleeping Mode

By pushing the button when the display is on the main frame, the

remote control will continue to work, but the display will switch off. To

switch on the display push the button again.

Standby Mode

By pushing the button for 3 seconds when the main frame is displayed

,it is possible to switch off completely the remote control and thus

reduce the battery consumption. This feature is to be used in case of

prolonged non-use of remote control. If the function is activated, the

system uses the room probe connected to the Controller.

To switch on the remote control push the button twice.

2.2 The Display

Pushing the button the display turns on and the main frame appears.

-Errors:

Er01: Error Safety High Voltage 1. Also with the system Off.

Er02: Error Safety High Voltage 2. Only if the Combustion Fan is On.

Er03: Extinguishing for exhaust under temperature.

Er05: Extinguishing for exhaust over temperature.

Er06: Pellet Thermostat open (backfire in the brazier)

Er07: Encoder Error. No Encoder signal.

Er08: Encoder Error. Combustion Fan regulation failed.

Er11: Real time clock error, day and time not correct due to prolonged absence of power supply

Er12: Extinguishing for Ignition failed.

Er15: Lack of voltage supply.

Er17: Air Flow Regulator error.

Pag. 5 / 9DMAN63W0000020-2Ways2 Manual - System100 Hydro STD2

Er18: Run out of pellet

Er23: Boiler probe or Buffer probe open

Er25: Error Engine cleaning Brazier

Er39: Air Flow Regulator Sensor broken.

Er41: Minimum air flow in Check Up not reached.

Er42: Maximum air flow Up reached (F40).

Er44: Open door error.

Er47: Auger Encoder error, no Encoder signal.

Er48: Auger Encoder error: auger speed regulation failed.

Er52: I/O I2C Module error

Er57: Test ’Forced Draught High’ in Check Up fail (FL70)

Service: It notifies that the planned hours of functioning (parameter T66) is reached. It is necessary to

call for service.

-Other messages:

Prob: Visualization of the state of temperature probes. The message displayed in Check-Up indicates

that the red temperature on one or more probes is equal to the minimum value (0°C) or maximum (it

depends on probe considered). Check that the probes aren’t open (0°C) or in short-circuit (maximum

value of the temperature scale).

Clean: This message notifies that the planned hours of functioning (parameter T67) is reached. It is

necessary to clean the stove or boiler.

Block-Ignition: The message appears if the system is turned off during Ignition (after Preload) by an

external device: the system will stop only when it goes in Run Mode.

Door: The message notifies that the door is open.

Cleaning On: Periodic Cleaning in progress.

-Battery Charge Level:

Maximum battery charge

Battery discharged; replace the

battery as soon as possible. The

image blinks.

Battery charge at 2/3

Battery charge at a 1/3

3The Menu

To enter the Menu press the SET key on the remote control. The Submenu list or the parameter list will

appear with the current set value:

The storage of a new value is associated to the transmission to the control board; if it fails the message

'Transfer not successful '

appears.

In this case try to modify again the parameter’s value.

Auger

C01 1.0_________

C02 1.2

C03 4.1

C04 5.6

C05 6.2

C05 7.4

System Menu

Auger____________

Combustion Fan

Combustion Fan 2

Heating Fan

Thermostats

Timers

Auger

C01

Max: 60.0

Set: 1.0

Min: 0.0

Submenu

Parameter Code

Maximum Value

Current Value

Minimum Value

Pag. 6 / 9DMAN63W0000020-2Ways2 Manual - System100 Hydro STD2

3.1 Main Thermostat Modification

Use the buttons to change the Radio

Room Thermostat value (it is possible only if it

has not been disabled in the specific Menu).

The value can be modified using the same

buttons, save data occurs automatically at the exit

of Menu or pushing SET key.

3.2 User Menu

DESCRIPTION

Combustion

Management

Power

It allows to modify the combustion power of the system in Pellet mode. It can be set

in automatic or manual mode. In the first case, the system chooses the combustion

power. In the second case, the user selects the desired power. On the left side of the

display is signalled the combustion modality (

=automatic combustion,

=manual

combustion) and the working power level of the system.

Recipe

Menu to select the combustion recipe. The maximum value is the number of recipes

visible to the user (parameter P04). If P04=1 the Menu is not visible.

Auger Calibration

It allows to modify the default value of the Auger’s speed and On Times. The values

are in the range –7 ÷ 7. The default value is 0.

Fan Calibration

It allows to modify the default value of the Combustion Fan speed. The values are in

the range –7 ÷ 7. The default value is 0.

Heating

Management

Boiler Thermostat

It allows to modify the value of the Boiler Thermostat. You can choose the minimum

and maximum values by setting the corresponding thermostats T26 and T27.

Buffer tank Thermostat

It allows to modify the value of the Buffer tank Thermostat. It will be visible only if

you select a plumbing plant including a Buffer Probe (P26=2, 3, 4).

Heating Power

It allows to change the power of the fan heating. This menu is visible only by setting

an output configurable to 6 and A04=0. You can set the management of the heating

system in automatic or manual mode.

Heating

Description

0FF

Heating fan is stopped (it is possible only if P95=0)

1–Power user

number

Power is adjusted manually from 1 to the maximum number of

power user (parameter P03)

Auto

Power is adjusted automatically according to the value of the

parameter P06

Stove Room Thermostat

It allows to modify the value of the Local Room Thermostat. It is visible only if a

configurable input is set as Room Probe.

Summer-Winter

The user may select between Summer-Winter mode.

Chrono

Menu to select the Chrono Program modality and to set the time of

Ignition/Extinguishing of the boiler/stove.

For more details please see section 3.2.1.

Monitor

This Menu shows some System data of interest

Display

Description

Exhaust T.

Exhaust temperature [°C]

Termostato

Ambiente Radio

Set: 20°C

Pag. 7 / 9DMAN63W0000020-2Ways2 Manual - System100 Hydro STD2

Stove Room T.

Room Temperature detected by the board [°C] (visible only if

an input is set as Room Probe)

Buffer T.

Buffer tank Temperature [°C] (visible only if P26=2, 3, 4)

Pressure

Water Pressure [mbar]

Air Flow

Air Flow [cm/s]

Fan

Combustion Fan speed [RPM] (visible only if P25=1, 2)

Auger

Auger working time [s] (visible only if P81=0)

Recipe

Current combustion recipe [nr] (visible only if P04>1)

Product Code

Product Code: 537

FSYSI01000060.0.0

Control board firmware code and version

FSYSC02000032.0.0

Remote Control firmware code and version

Manual Load

The procedure activates the pellet manual loading with activation in continuous

modality of the Auger motor. The loading stops automatically after 600 seconds. The

system must be OFF for the function can be activated

Cleaning Reset

Menu to reset the ‘System Maintenance 2’ function. It is visible only if T67>0.

Settings

Thermostat Management

Menu to set the Radio Room thermostat functioning.

Thermostat Status

Description

Enabled

The Radio Room Thermostat is used by the system

Disabled

The system uses the thermostats of the control panel and, on

the main frame of the display, the value and the image of the

thermostat will disappear.

Radio Standby

Menu to completely switch off the remote control and lower the battery consumption

Description

Display

Push the SET button to enable the Standby mode. To

turn on the radio again, first push the key and then

the button twice.

If the function is activated, the system uses the room

probe connected to the control board.

This feature is to be used in case of prolonged non-use

of the radio terminal.

Time and Date

Menu to set time and date.

Description

Keys

Display

Select hours, minutes, year, month and day

Enter editing

SET

Modify the value

Save

SET

Exit

ESC

Radio Test

This Menu is used to test the connection between the radio terminal and the control

board, thereby verifying the level of the electromagnetic pollution. The Terminal

Radio enters in continuous transmission and counts the correct and failed answers.

The quality of the signal depends on the number of the errors.

Change Code

Code changing allows matching the remote control with a specific board, so that a

remote control is matched only with a specific stove or boiler (thus permitting the

coexistence of different systems in the same area). In order to change the code:

select a code

enter the Learn Menu of the control board and push the set key

push the SET button on the terminal radio and verify the result of the

operation

Contrast Setting

This Menu allows setting the display contrast

Description

Keys

Display

Modify the value

Set Contrast

Time and Date

16:45

Thursday

07/02/2016

Standby

Radio

Enable _____

Pag. 8 / 9DMAN63W0000020-2Ways2 Manual - System100 Hydro STD2

Save

SET

Exit

ESC

Key Tone

Menu to enable or disable the key tone.

Language Selection

Menu to change the language. The highlighted language is the one currently set.

System Menu

Menu to enter in the Technical Menu.

It is protected by password: the default password is 0000.

Push SET to enter in editing mode, and to increase or decrease the selected

digit. Push SET to save the digit and pass to the next. Push ESC to cancel the digit

or exit from Menu. If the password is right, the first menu screen appears.

Description

Auger

Auger Menu

Combustion Fan

Combustion Fan Menu

Exhaust Fan 2

Exhaust Fan 2 Menu

Heating Fan

Heating Fan Menu

Thermostats

Thermostats Menu

Extinguishing Th

Extinguishing Thermostats Menu

Timers

Timers Menu

Enables

Enables Menu

Air Flow Sensor

Primary Air Regulator Menu

Counters

Counters Menu

Outputs’ Test

Outputs’ Test Menu

Restore Default Value

Menu to restore the parameters’ values set by the

manufacturer

3.2.1 Chrono Menu

Menu to set the system ignition/extinguishing times.

3.2.1.1. Chrono Modality

To turn on the system by chrono, select the modality after the programming the ignition/extinguishing times

Description

Keys

Display

The current modality is highlighted and blinks

Select the favourite modality

Cancel the changes and restore the old modality

ESC

Save the new setting

SET

Exit from Menu

ESC

3.2.1.2. Chrono Programming

Choose the type of programming to set (after making the programming it is necessary to select the desired

mode from the Modality Menu to turn on/off the system by Chrono):



Daily:

Select the day of week and program the system ignition/extinguishing times; for each day there

are 3 time slots.

Daily

Monday___________

Tuesday

Wednesday

Thursday

Friday

Saturday

Venerdì

Programming

Daily________

Weekly

Week-End

Daily

Monday

ON OFF

09:30 11:15

00:00 00:00

Modality

Chrono Modality

Disable

Daily

Weekly

Week-End

Pag. 9 / 9DMAN63W0000020-2Ways2 Manual - System100 Hydro STD2

Program across midnight

Set the hour of extinguishing of a day at 23:59 and set the hour of ignition for the next day at 00:00.



Weekly:

Program the times to switch on and off the system (there are 3 time slots).



Week-End:

Choose between 'Monday-Friday' and 'Saturday-Sunday'. There are 3 time slots for each

period.

The three types of programming are stored separately: if for example the Daily modality is set, the other

modalities are not changed.

Program Chrono

Keys

After choosing the favourite program:

Select the programming time

Enter in modify mode (the selected time blinks)

SET

Modify the timers

Save program

SET

Enable a program ( appears) or disable it ( appears)

Exit

ESC

Week-End

Mon-Fri__________

Sat-Sun

Programming

Daily

Weekly

Week-End

Mon-Fri

ON OFF

09:30 11:15

00:00 00:00

Programming

Daily

Weekly

Week-End

Weekly

Mon-Sun

ON OFF

09:30 11:15

00:00 00:00

Tabla de contenidos

Otros manuales de Mando a distancia de TiEmme

TiEmme

TiEmme 4HEATModule Manual de usuario

TiEmme

TiEmme 4HEATModule Manual de usuario

Manuales populares de Mando a distancia de otras marcas

Panasonic

Panasonic EUR7622KB0 Manual de usuario

Bang & Olufsen

Bang & Olufsen Beo4 Manual de usuario

Sunwave Tech.

Sunwave Tech. RemoteComm SRC-7000 Manual de usuario

Multiplex

Multiplex PROFI TX 9 Manual de usuario

One Remote

One Remote RMB4 Manual de usuario

FUTABA

FUTABA 9ZAP - PART2 Manual de usuario

HR Matic

HR Matic HR MULTI 3 Manual de usuario

Yamaha

Yamaha ACC-GNRST-30-20 Manual de usuario

EisSound

EisSound KBSOUND Manual de usuario

Marantz

Marantz RC101 Manual de usuario

Conrad

Conrad FS20 TC6 Manual de usuario

Anritsu

Anritsu MP1777A Manual de usuario

Niles

Niles WVC100 Guía de solución de problemas

RCA

RCA RCU1300 Manual de usuario

Bang & Olufsen

Bang & Olufsen BEO6 Manual de usuario

GE 94901 Manual de usuario

Onbon

Onbon YQ1-75 Manual de usuario

FUTABA

FUTABA R7108SB Instrucciones de instalación