Tieline Bridge-IT XTRA Manual de usuario

Bridge-IT XTRA

IP Codec User Manual

Software Version: 2.14.88

Manual Version: v.2.2_20151125

November, 2015

Bridge-IT XTRA Manual2

Table of Contents

Part I How to Use the Documentation 5

Part II Warnings and Safety Information 6

Part III Glossary of Terms 11

Part IV Introduction to Bridge-IT XTRA 13

Part V XTRA Front Panel Controls 14

Part VI XTRA Rear Panel Connections 16

Part VII Navigating Codec Menus 17

Part VIII Adjusting Input/Meter Levels 22

Part IX Configuring AES3 Audio 26

Part X Headphone/Output Monitoring 28

Part XI Language Selection 29

Part XII About Program Dialing 30

Part XIII Getting Connected Quickly 32

................................................................................................................................... 32110 Quick Steps to Connect Bridge-IT

................................................................................................................................... 352Monitoring IP Connections

................................................................................................................................... 373Load and Dial Custom Programs

................................................................................................................................... 374Disconnecting a Connection

................................................................................................................................... 385Redialing a Connection

................................................................................................................................... 386Configuring Auto Reconnect

................................................................................................................................... 397Speed Dialing Connections

................................................................................................................................... 398Dial/Disconnect Multiple Connections

................................................................................................................................... 409Creating a Multicast Server Program

................................................................................................................................... 4310 Creating a Multicast Client Program

................................................................................................................................... 4511 Dialing SIP Peer-to-Peer

................................................................................................................................... 4612 Dialing SIP Addresses

................................................................................................................................... 4713 Deleting Programs

................................................................................................................................... 4714 Selecting Algorithm Profiles

................................................................................................................................... 5015 SDHC Card Backup

................................................................................................................................... 5016 SDHC Card File Playback

................................................................................................................................... 5117 Lock or Unlock a Program in the Codec

................................................................................................................................... 5218 Locking the Front Panel

3Contents

Part XIV Connecting to the ToolBox

Web-GUI 53

................................................................................................................................... 541Opening the Java or HTML5 Web-GUI & Login

................................................................................................................................... 572Changing the Default Password

................................................................................................................................... 583Installing USB Drivers

................................................................................................................................... 594Launching the GUI over USB

Part XV Java Toolbox Web-GUI

Introduction 59

Part XVI Java Toolbox Web-GUI Codec

Configuration 67

................................................................................................................................... 671Configuring IP Settings

................................................................................................................................... 722Configuring Input/Output Settings

................................................................................................................................... 763Configuring Mono or Stereo Peer-to-Peer Programs

................................................................................................................................... 824Configuring Multi-Unicast Dialing Programs

................................................................................................................................... 875Configuring Multicast Server Programs

................................................................................................................................... 916Configuring Multicast Client Programs

................................................................................................................................... 947Configuring SIP Settings

................................................................................................................................... 968Configuring SIP Programs

................................................................................................................................... 1009Dial and Disconnect a Program

................................................................................................................................... 10110 Dial and Disconnect Multi-unicast Connections

................................................................................................................................... 10311 Lock or Unlock Programs

................................................................................................................................... 10312 View/Edit/Delete Programs

................................................................................................................................... 10613 Reset Factory Default Settings

................................................................................................................................... 10714 Backup and Restore Functions

................................................................................................................................... 10915 Web-GUI Software License Installation

................................................................................................................................... 11016 Download Logs

................................................................................................................................... 11117 RS232 Data Configuration

................................................................................................................................... 11218 Creating Rules

................................................................................................................................... 11619 Upgrading Codec Firmware

Part XVII HTML5 Toolbox Web-GUI

Introduction 118

Part XVIII HTML5 Toolbox Web-GUI

Configuration 129

................................................................................................................................... 1291Using the HTML5 Toolbox Quick Connect Web-GUI

................................................................................................................................... 1342Configuring IP Settings

................................................................................................................................... 1383Configuring Input/Output Settings

................................................................................................................................... 1404Configure SIP Settings

................................................................................................................................... 1435Load, Unload and Dial a Program

................................................................................................................................... 1466Lock or Unlock Programs

Bridge-IT XTRA Manual4

................................................................................................................................... 1477Reset Factory Default Settings

................................................................................................................................... 1488Backup and Restore Functions

................................................................................................................................... 1499HTML5 Software License Installation

................................................................................................................................... 15010 Download Logs

................................................................................................................................... 15111 RS232 Data Configuration

................................................................................................................................... 15312 Creating Rules

................................................................................................................................... 15713 Upgrading Codec Firmware

Part XIX Front Panel Configuration Tasks 158

................................................................................................................................... 1581Configuring IP via the Front Panel

................................................................................................................................... 1612Selecting an Algorithm

................................................................................................................................... 1673Configuring the Jitter Buffer

................................................................................................................................... 1704Configuring Forward Error Correction

................................................................................................................................... 1725Configuring Encode/Decode Direction

................................................................................................................................... 1726Bridge-IT XTRA Relays and RS232 Data

................................................................................................................................... 1747Configuring TCP/UDP Ports

................................................................................................................................... 1768Configuring QoS for Broadcasts

................................................................................................................................... 1779Configuring Data Packet Time-to-Live

................................................................................................................................... 17810 Reset and Restore Factory Default Settings

................................................................................................................................... 17811 Installing Software Licences

Part XX Reference 180

................................................................................................................................... 1801Regular Maintenance

................................................................................................................................... 1812Installing the Codec at the Studio

................................................................................................................................... 1873Understanding IP Networks

................................................................................................................................... 1894Tips for Creating Reliable IP Connections

................................................................................................................................... 1905Testing IP Network Connections

................................................................................................................................... 1926Software Licences

................................................................................................................................... 2007Compliances and Certifications

................................................................................................................................... 2028Trademarks and Credit Notices

Part XXI Bridge-IT XTRA Specifications 203

Index 204

Bridge-IT XTRA Manual

1How to Use the Documentation

Overview of this User Manual

Use this manual to learn how to:

·Connect the codec to an IP network and configure peer-to-peer, multicast or multi-unicast

connections.

·Configure the codec over aLAN or USB cable.

·Adjust audio and other settings within the codec.

·Configure automatic SDHC card backup.

Please read Getting Connected Quickly for an overview of how to configure the codec using

'programs' to store connection settings.

Manual Conventions

Warnings: Instructions that, if ignored, could result in death or serious personal injury

caused by incorrect operation of the equipment. These must be observed for safe operation.

Cautions: Instructions warning against potential hazards, or to detail practices that must be

observed for safe operation and to prevent damage to equipment or personnel.

Important Note: Information you should know to connect and operate your codec

successfully.

Typographic Conventions

·Codec software elements are in Arial bold, e.g. Contacts

·Codec hardware elements are in bold Capitals, e.g. KEYPAD

Help Button

Press the (information/help) button on the codec when navigating codec menus to display a

help dialog on the LCD screen suggesting actions which can be performed from the current menu

item.

6Bridge-IT XTRA Manual

2Warnings and Safety Information

THUNDERSTORM AND LIGHTNING WARNING:

DO NOT USE Tieline codecs during thunderstorms and lightning. You may suffer an injury

using aTieline codec, or any device connected to aLAN connection during athunderstorm.

This can lead to personal injury and in extreme cases may be fatal. Protective devices can

be fitted to lines, however, due to the extremely high voltages and energy levels involved in

lightning strikes, these devices may not offer protection to users, the Tieline codec and

equipment connected to the codec.

Secondary strikes can occur. These secondary strikes are induced by lightning strikes and

also produce dangerously high currents and energy levels. You only need to be near an

object struck by lightning to lead to personal injury or damage to equipment. e.g. if located

near alighting tower at asports facility, water features and drains on golf courses you may

be affected by these secondary strikes.

Damage to personnel and Tieline codecs may occur during thunderstorm, even if the codec

is turned off but is connected to the system or the power.

ANY DAMAGE TO ATIELINE PRODUCT CAUSED BY LIGHTNING or an ELECTRICAL

STORM WILL VOID THE WARRANTY. Use of this product is subject to Tieline's

SOFTWARE LICENSE and WARRANTY conditions, which should be viewed at

www.tieline.com/support before using this product.

SAFETY PRECAUTIONS:

·Areadily accessible disconnect device shall be incorporated in the building installation

wiring.

·Due to the risks of electrical shock, and energy, mechanical, and fire hazards, any

procedures that involve opening panels or changing components must be performed by

qualified service personnel only.

·To reduce the risk of fire and electrical shock, disconnect the device from the power line

before removing the cover or panels.

·This unit has more than one power supply. Disconnect all power supplies before opening

to avoid electric shock. Disconnecting one power supply disconnects only one power

supply module. To isolate the unit completely, disconnect all power supplies.

SERVICING WARNINGS:

·Do not perform any servicing other than that contained in the operating instructions unless

you are qualified to do so.

·All work should be carried out by suitably qualified personnel.

·This unit has more than one power supply. Disconnect all power cables before

maintenance to avoid electric shock.

HIGH VOLTAGE WARNINGS:

·Any adjustment, maintenance, and repair of the opened instrument under voltage must be

avoided as much as possible and, when inevitable, must be carried out only by askilled

person who is aware of the hazard involved.

·Capacitors inside the instrument may still be charged even if the instrument has been

disconnected from its source of supply.

GROUNDING:

Before connecting this device to the power line, where required, the protective earth terminal

screws of this device must be connected to the protective earth in the building installation.

LINE VOLTAGE:

Before connecting this device to the power line, make sure the voltage of the power source

Bridge-IT XTRA Manual

matches the requirements of the device. Refer to the device Specifications for information

about the correct power rating for the device.

FUSES:

Make sure that only fuses with the required rated current and of the specified type are used

for replacement. The use of repaired fuses and the short-circuiting of fuse holders must be

avoided. Whenever it is likely that the protection offered by fuses has been impaired, the

instrument must be made inoperative and be secured against any unintended operation.

WARNING:

HIGH LEAKAGE CURRENT. EARTH CONNECTION ESSENTIAL BEFORE CONNECTING

SUPPLY.

If the total leakage current exceeds 3.5 mA, or if the leakage current of the connected

loads is unknown, connect the supplementary ground terminal to areliable ground

connection in your facility.

SUPPLEMENTARY GROUND CONNECTION:

Asupplementary ground terminal is provided on the codec to connect the unit to aground

connection. The ground terminal has an M4 stud with M4 retaining nuts and is compatible

with all grounding wires. Remove only the outer NUT to connect your ground wire. The

ground wire must have asuitable lug. When refitting the outer NUT ensure that both NUTS

are correctly tightened to establish and maintain aproper earth connection.

WARNING: To Reduce the Risk of Electrical Shock and Fire

1. This equipment is designed to permit connection between the earthed conductor of the

DC supply circuit and the earthing conductor equipment.

2. Equipment connected to the protective earthing of the building installation through the

mains connection or through other equipment with aconnection to protective earthing -

and to acable distribution system using coaxial cable, may in some circumstances

create afire hazard. Connection to acable distribution system must therefore be

provided through adevice providing electrical isolation below acertain frequency range

(galvanic isolator, see EN 60728-11).

3. All servicing must be undertaken only by qualified service personnel. There are not user

serviceable parts inside the unit.

4. DO NOT plug in, turn on or attempt to operate an obviously damaged unit.

5. Ensure that the chassis ventilation openings in the unit are NOT BLOCKED.

6. Do not operate the device in alocation where the maximum ambient temperature

exceeds 50°C (122°F), or is below 0°C (32°F).

7. Be sure to unplug both power supply cords from the wall socket BEFORE attempting to

service the power supply fuse.

AC units for Denmark, Finland, Norway, Sweden (marked on product):

•Denmark -“Unit is class I-unit to be used with an AC cord set suitable with Denmark

deviations. The cord includes an earthing conductor. The Unit is to be plugged into awall

socket outlet which is connected to aprotective earth. Socket outlets which are not

connected to earth are not to be used!”

•Finland -“Laite on liitettävä suojamaadoituskoskettimilla varustettuun pistorasiaan”

•Norway -“Apparatet må tilkoples jordet stikkontakt”

•Unit is intended for connection to IT power systems for Norway only.

•Sweden -“Apparaten skall anslutas till jordat uttag.”

To connect the power connection:

1. Connect the power cables to the power sockets, located on the rear panel of the device.

8Bridge-IT XTRA Manual

2. Connect the power cables to the grounded AC outlets.

WARNING: Risk of electric shock and energy hazard. Disconnecting one power supply

disconnects only one power supply module. To isolate the unit completely, disconnect all

power supplies.

CHINESE SAFETY WARNINGS:

Translation of previous Chinese safety warning: This unit has two power supplies, please be

very careful when using, disconnect two power supplies before maintenance to avoid electric

shock.

This device must only be used in not-tropical climate regions.

This device must only be used at altitude not exceeding 2000 metres.

JAPANESE SAFETY WARNINGS:

Translation of previous warning: Provide an earthing connection.

Translation of previous warning: Provide an earthing connection before the mains plug is

connected to the mains. And, when disconnecting the earthing connection, be sure to

disconnect after pulling out the mains plug from the mains.

Statement for Class AVCCI-certified Equipment:

Translation of previous Class AVCCI Statement: This is aClass Aproduct based on the

standard of the Voluntary Control Council for Interference by Information Technology

Equipment (VCCI). If this equipment is used in adomestic environment, radio disturbance

may occur, in which case, the user may be required to take corrective action.

Bridge-IT XTRA Manual

Statement for Class BVCCI-certified Equipment:

Translation of previous Class BVCCI Statement: This is aClass Bproduct based on the

standard of the Voluntary Control Council for Interference by Information Technology

Equipment (VCCI). If this is used near aradio or television receiver in adomestic

environment, it may cause radio interference. Install and use the equipment according to the

instruction manual.

Special Notices for North American Users:

For North American power connection, select apower supply cord that is UL Listed and

CSA Certified 3-conductor, [18 AWG], terminated in amolded on plug cap rated 125 V, [5

A], with aminimum length of 1.5m [six feet] but no longer than 4.5m.

Special Notices for European Users:

For European connection, select apower supply cord that is internationally harmonized and

marked “<HAR>”, 3-conductor, 0,75 mm2 minimum mm2 wire, rated 300 V, with aPVC

insulated jacket. The cord must have amolded on plug cap rated 250 V, 3A.

Installation Codes:

This device must be installed according to country national electrical codes. For North

America, equipment must be installed in accordance with the US National Electrical Code,

Articles 110 -16, 110 -17, and 110 -18 and the Canadian Electrical Code, Section 12.

Interconnection Cabling:

Cables for connecting to the unit's RS232 and Ethernet Interfaces must be UL certified type

DP-1 or DP-2. (Note: when residing in non-LPS circuit)

Overcurrent Protection:

Areadily accessible listed branch-circuit over current protective device rated 15 Amust be

incorporated in the building wiring for each power input.

Replaceable Batteries:

If equipment is provided with areplaceable battery, and is replaced by an incorrect battery

type, then an explosion may occur.

CAUTION: RISK OF EXPLOSION IF BATTERY IS REPLACED BY AN INCORRECT

BATTERY TYPE. DISPOSE OF USED BATTERIES ACCORDING TO THE INSTRUCTIONS.

This equipment is provided with along life replaceable Panasonic CR2032 model 3V

manganese dioxide lithium coin battery. Service personnel should only replace this battery

with the same brand and type of battery. If this is replaced by an incorrect battery type, then

an explosion may occur. Visit http://www.panasonic.com/industrial/includes/pdf/

Panasonic_LithiumCR_Info.pdf to view the Material Safety Data Sheet for this battery.

10 Bridge-IT XTRA Manual

End of Life Statement

Tieline hereby declares that all materials, components and products supplied are in full compliance

with RoHS &WEE directives. This product must be disposed of according to local laws and

regulations. Because the product contains abattery it must be disposed of separately from

household waste. Do not incinerate, but take it to arecycling facility.

Disclaimer

Whilst every effort has been made to ensure the accuracy of this manual we are not responsible for

any errors or omissions within it. The product specifications and descriptions within this manual will

be subject to improvements and modifications over time without notice, as changes to software and

hardware are implemented.

Tabla de contenidos

Otros manuales de Hardware de red de Tieline

Tieline

Tieline Merlin Manual de usuario

Tieline

Tieline Bridge-IT Manual de usuario

Tieline

Tieline Merlin PLUS Manual de usuario

Tieline

Tieline Genie STL Manual de usuario

Manuales populares de Hardware de red de otras marcas

Matrix Switch Corporation

Matrix Switch Corporation MSC-HD161DEL Manual de usuario

B&B Electronics

B&B Electronics ZXT9-IO-222R2 Manual de usuario

Yudor

Yudor YDS-16 Manual de usuario

D-Link

D-Link ShareCenter DNS-320L Manual de usuario

Samsung

Samsung ES1642dc Instrucciones de uso

Honeywell Home

Honeywell Home LTEM-PV Instrucciones de montaje

evertz

evertz 7700 Series Manual de usuario

D-Link

D-Link ShareCenter DNS-343 Manual de usuario

Asante

Asante AsanteBridge 1012 Manual de usuario

FireBrick

FireBrick FB2700 Manual de usuario

Audiovox Electronics

Audiovox Electronics ARWH2T Manual de usuario

ADC

ADC DSX-1 Manual

NetComm

NetComm NF2 Manual de usuario

Alcatel-Lucent

Alcatel-Lucent 5620 Manual de usuario

Dell EMC

Dell EMC XC6420 Series Manual de usuario

Lanner

Lanner NCA-1020A Manual de usuario

Allied Telesis

Allied Telesis AT-TN121-A Manual de usuario

Arista

Arista CCA-ETM-Q12 Manual de usuario