TIDRADIO TD-H5 Instrucciones de funcionamiento
1
TIDRADIO TD-H5 Programming Guide
INTRODUCTION
TIDRADIO TD-H5 is a dual-band (VHF, UHF) gmrs radio. It offers 250 memory
channels, you can add or remove channels from scanning list and give channels
alphanumeric names via programming with a computer. With the enhanced
capabilities of the H5 radio, this Programming Guide will help you get a quick
start to program the radio.
*If you have any problem with the TD-H5 radio using or programming, please
don’t hesitate to contact us via support: walkietalkiesoftware.com. Also visit our
Facebook home pages (TIDRADIO) for more help.It’s always our honor to help.
Contents
1. Frequency Chart......................................................................................................2
2. Preparation before Programming.......................................................................2
3. Manufacture Software Programming Process ................................................6
2
1. Frequency Chart
22 Modifiable GMRS Two Way Channels (Channels 1-22) - Receive and
Transmit.
8 Modifiable GMRS Repeater Channels (Channels 23-30) - Receive and Transmit.
24 Modifiable Repeater Channels (Channels 31-54) - Receive and Transmit.
2. Preparation before Programming
2.1. Computer System Requirements
Manufacture Programming Software Operating System: Windows 7, Windows 8
and Windows 10
2.2. Programming Cable
A.CH340 USB programming cable is Included - The driver should be installed
before programming.
3
Driver download link:walkietalkiesoftware.com
1) Find the corresponding driver of the system.
2) Click and wait for the download.
3) Click install and wait for the installation.
Come with the CH340 USB programming cable is only suitable for
WINDOWS system
B. If you use an FTDI cable (not included) , it does not need to be installed with a
driver.You can just plug in and use directly.(suitable for Mac os,Windows system)
You can search B08CB5KT5M on Amazon to purchase a FTDI cable if you do not
have one.
Product link:
https://www.amazon.com/TIDRADIO-Programming-BaoFeng-Retevis-Radioddi
ty/dp/B08CB5KT5M/ref=sr_1_1?dchild=1&keywords=B08CB5KT5M&qid=16279
73909&sr=8-1
1) If your computer did not automatically install the driver, you will need to
update the driver to the latest driver
Download the latest FTDI driver at :https://ftdichip.com/drivers/vcp-drivers/
4
2.3. Software Download & Install
1) Turn on the computer, check if your computer system meets the
requirements.
2) Download the manufacture software on walkietalkiesoftware.com
3) Install the programming software
2.4. Connect your Walkie Talkie with Computer
1) USB programming cable connects with the computer end.
2) Connect the other end of the cable with your walkie talkie.
3) When both ends have been connected, turn on your radio. Make sure it has
enough power during the programming procedure.
ERROR: Failed to Connect to the transceiver (Radio)
If it says it cannot connect to the radio - this means the cable is working but is not installed correctly
into the radio.
Items to Check:
Radio is turned on
The cable is FULLY inserted (it can be deceiving but there is a double click)
Hold the cable into the radio - some radios might not make contact without pressure
A way to cheat - dampen the pins of the cable before pushing it into the radio. This will give a
solid contact
5
2.5.How to choose your port?
1)Get into “Window Setting”, then search “Device Manager”.
2)Open “Device Manager”, and unfold Port (COM & LPT) to check the existing
port.
6
3)Come with CH340 programming cable port is USB-SERIAL CH340 (COM?)
4)FTDI programming cable port is USB Serial Port (COM?)
3.TD-H5 Manufacture Software Programming Process
1)Download and open the manufacture software. Click "Program →
Communication Port" and then Confirm the port the same as the port viewed by
Device Manager, then click the ”OK” button.
7
2) Click "Program → Read from Radio", then click "OK" and ready to read the
data from your radio.( Make sure the radio is turned on)
3) You will come to the Radio Information page and then click “ Channel ” to
Channel page.
4) In channel page, you can adjust the limited parameters ( Name, Rx QT/DQT,
Tx QT/DQT, Wide/Narrow, Power, PTT-ID, etc.). The RX frequency and TX
frequency of channel 1-54 are fixed, so you cannot change it. Channel 55-250
can only receive frequencies but not transmit frequencies.
8
9
Channel Information
The H5 radio has 250 channels, you can edit the channel information according
to your needs. The following is an introduction to each term.
Name
Meaning
Setting
Description
RX Freq
Receiving frequency
VHF:136-174MHz
UHF:400-520MHz
TX Freq
Transmitting frequency
GMRS frequency（Fixed）
Name
Customize channel
name
Up to 6 digits.
Support alphanumeric channel na
me.
RX
QT/DQT
Receiving CTCSS/DCS
Refer to the DCS table and
CTCSS table in the manual.
Mutes the speaker of the transceiv
er in the absence of a specific low-l
evel digital signal. If the station you
are listening to does not transmit t
his specific signal, you will not hear
anything.
TX
QT/DQT
Transmitting
CTCSS/DCS
Refer to the DCS table and
CTCSS table in the manual.
Transmits a specific and continuous
sub audible signal to unlock the
squelch of a distant receiver.
W/N
Channel bandwidth
WIDE/NARROW
Wideband (25kHz bandwidth)
narrowband (12.5 kHz bandwidth).
POWER
Transmit power
HIGH/LOW
High power:5W
Low power:1W
PTT-ID
When to send the
PTT-ID
OFF does not send
code;
BOT press PTT button to
send code;
EOT release PTT
button to send code;
BOTH press and
release PTT button to
send code
Codes are sent during either the
beginning or end of a transmission.
BusyLock
Busy Channel Lockout
YES/NO
YES: If the channel is occupied,
when you press the [PTT] key on
this channel, the radio will make a
beep tone and will not transmit any
signal.
NO: No matter if the channel is
occupied, the radio will transmit
the signal when you press the [PTT]
key.
10
Scan add
YES/NO
In the scan mode, whether add the
channel to the scan list.
YES: the channel is added to scan
list;
NO: the channel cannot be
scanned.
Signal
Signal code
1-15
Selects 1 of 15 DTMF codes. The
DTMF codes are programmed with
software and are up to 5 digits
each
Freq
Hopping
Code
OFF/ON
With this function, you can activate
the frequency hopping system,
improve the anti-interference
ability of the radio, and reduce the
risk of being monitored.
5) Click "VFO A" or “VFO B” or Channel Edit you can adjust the limited
parameters (Selected Channel, Power Level, Channel Spacing, Signaling Code,
Step Frequency , Freq Hopping, etc.)
Name
Setting
Description
Selected Channel
CH1-CH250,VFO A,VFO B
Select the channel for editing
Channel Spacing
Wide/Narrow
Signaling Code
1-15
Selects 1 of 15 DTMF codes. The DTMF cod
es are programmed with software and are u
p to 5
Tabla de contenidos
Otros manuales de Radio de TIDRADIO
