THRUSTME CRUISER Manual de usuario
INSTRUCTION MANUAL
thrustme.no
C R U I S E R
1
2
We recommend that you write down the serial number
in this manual for future reference.
Serial Number: C_ _ _ - _ _ _ _-_ _ _ _
This example will be written C006-2022-0010
EN
Sticker located here
LANGUAGE
English
Warnings and advisories at the end.
TABLE OF CONTENTS
What's included
How things work
How to fit on a kayak, canoe, SUP etc.
How to charge and store the batteries
Maintenance and service
Recycle and disposal
Spare parts and extras
Find your icon on the pages to learn more
Warranty
Warnings
EN
First time charging the Cruiser and remote
3
ADDITIONAL EQUPMENT
Fast charger
INPUT : 100 -240 VAC
OUTPUT : 21V/ 10 A
Charge time internal battery 1 hour
EN
12V Charger for Car/ Boat
INPUT : 12V - 48V DC/ 5A /50W
OUTPUT : 21V/ 2 A
Charge time internal battery 6 hour`s
Please contact your local dealer or visit our webpage for
ordering the products.
www.thrustme.no
Universal ThrustME tool
Tool for tightening screws or change worn parts
Propeller knife
Cuts seaweed, fishing line and other things that
might get caught in the propeller
4
INCLUDED
Mounting bracket x1
Wrist band for remote,
with floating element X1 CRUISER safety cord X1
Magnetic kill switch X1
(Also works as the main switch)
CRUISER charger 230V X1
CRUISER remote X1
EN
Harness for kayak, canoe and SUP x1
CRUISER motor X1
Backpack X1
5
QUICK GUIDE
EN
Congratulations with your CRUISER
For first time use –please do the following steps.
Connect the charger to the Cruiser
Attach the Kill switch
Verify that the display is ON
Insert the Remote in the Charging slot located
under the display to charge the remote
(kill switch) needs to be installed to charge the
remote.
NOTE : The remote control can also be charged on
a regular induction plate used on newer cell
phones.
After 20 minutes remove the Kill switch
Leave the Cruiser to be charged.
ENJOY YOUR CRUISER
Red-light on charger
indicates charging
Green-light Charging complete
If the Display is showing 100%, please continue charging until
you have green light on the charger.
6
MAIN FUNCTIONS
7
8
1
1. Upper pivot point.
2. 3-pin motor connector
3. Lower pivot point
4. Motor
5. Display
6. Wireless remote
7. Charge and external battery connection
8. Rotating swivel
23
4
5
6
1
3
4
1. Pivot screw (Loosen screw before rotating)
2. Jack for fastening the main bracket to the floating device
3. Attachment screw
4. Spring pin (Pull and set in rest position before rotating)
2
EN
7
2
4
3
5
1
6
1. Moment clip/ lock
2. Moment bracket, this prevents the CRUISER to move and keeps the CRUISER steady.
(Note: place the moment bracket above water level to prevent drag)
3. Velcro for belt length adjustment
4. Attachment plate for kayak, canoe, SUP , float plane, etc…
5. Jack for adjustment and fastener for main plate (jacking system)
6. Harness for kayak, canoe, SUP, float plane, etc…
Standard Length is 190 cm, when you have found the desired length, the excess can be cut off.
Pull to release
Lift & Jack for fastening
HARNESS (jacking system )
EN
8
DISPLAY FUNCTIONS
23
1. External battery status when connected
2. Indicator for reverse thrust
3. Indicator for stop ( the motor is not running )
4. Indicator for forward thrust (ex. showing motor running in STEP 5)
5. Battery indicator (ex. showing 48% remaining of the battery)
6. Remote connected
7. Internal battery charging
1
4
The CRUISER is protected with an automatic circuit breaker and temperature sensors.
If the motor stops while running, it needs to be reset. Before resetting check that the
propeller is free for seaweed or other objects. If the battery temperature is too high,
the CRUISER needs time to cool down.
Remove kill switch and re-connect for system reset.
5
6
7
ENDURANCE CHART
NOTE: This endurance chart is only a guideline; endurance may vary depending on
weather, temperature and type of watercraft used.
STEP 6 is a «Boost mode». When this is engaged endurance time will decrease
rapidly
EN
9
1. Hole for wrist band
2. Reverse thrust (one push = one step)
3. Stop
4. Forward thrust (one push = one step)
5. Charging and indicator light, pulses while charging
To change direction you always need to push the stop button first.
NOTE: The remote vibrates when a button is pushed
NOTE: Remote is equipped with 2,4 GHz system transmitting with only 1mV, so the
range is limited to approx. 75m.
REMOTE FUNCTIONS
When new, the remote is paired from the factory.
The remote has a unique address and only one remote can control one system. If
the remote is lost or not connected to the system,
pairing is needed. See instructions on next page.
EN
Remote (removable)
5
4
3
2
1
10
Otros manuales para CRUISER
1
Otros manuales de Motor fuera de borda de THRUSTME
