THORLABS CM100 Manual de usuario

Reflective Confocal Microscope

CM100

User Guide

Information in this document is subject to change without notice. The software described in this document is furnished under a license agreement or

nondisclosure agreement. The software may be used or copied only in accordance with the terms of those agreements. No part of this publication may be

reproduced, stored in a retrieval system, or transmitted in any form or any means electronic or mechanical, including photocopying and recording for any

purpose other than the purchaser's personal use without the written permission of ThorLabs, Inc..

ThorLabs, Inc.

108 Powers Court

Sterling, VA 20166

703-651-1700

Chapter 1 Warning Symbols and Definitions 1

Chapter 2 Safety 2

Chapter 3 Description 3

3.1. Features at a Glance 3

3.2. Imaging Capabilities 3

Chapter 4 Getting Started 4

4.1. Unpacking and Inspection 4

4.2. Setting up the CM100 5

4.3. Cable Connection Diagram 8

Chapter 5 Alignment 9

5.1. Widefield Imaging 18

Chapter 6 Maintaining the CM100 19

6.1. Cleaning 19

6.2. Connector Cleaning 19

6.3. Troubleshooting 19

Chapter 7 Specifications 20

Chapter 8 Mechanical Drawing 23

Chapter 9 Regulatory 24

9.1. Waste Treatment is Your Own Responsibility 24

9.2. Ecological Background 24

Chapter 10 Thorlabs Worldwide Contacts 25

Table of Contents

CM100

Chapter 1 Warning Symbols and Definitions

Below is a list of warning symbols you may encounter in this manual or on your device.

Symbol Description

Direct Current

Alternating Current

Both Direct and Alternating Current

Earth Ground Terminal

Protective Conductor Terminal

Frame or Chassis Terminal

Equipotentiality

On (Supply)

Off (Supply)

In Position of a Bi-Stable Push Control

Out Position of a Bi-Stable Push Control

Caution: Risk of Electric Shock

Caution: Hot Surface

Caution: Risk of Danger

Caution: Laser Radiation

Caution: Spinning Blades May Cause Harm

Page 1 TTN118785-D02

CM100 Chapter 1: Warning Symbols and Definitions

Chapter 2 Safety

All statements regarding safety of operation and technical data in this user guide will only apply

when the unit is operated correctly. Refer to the relevant User Guide of the individual product for

safety instructions. Please read the following warnings and cautions carefully before operating the

device.

WARNING

DO NOT use the device for anything other than its intended use. If the device is used in a

manner not specified by Thorlabs, the protection provided by the equipment may be

impaired.

WARRANTYWARNING

DO NOT open the scanner block, electronics enclosure, detector module or computer.

There are no serviceable parts in these products. DONOTperform instrumentation

maintenance or service except as specifically stated. Any modification or servicing of this

system by unqualified personnel renders Thorlabs free of any liability. Only personnel

authorized by Thorlabs and trained in the maintenance of this equipment should remove

any covers or housings or attempt any repairs or adjustments.

CAUTION

The computer supplied with this system requires configuration for specific ACline voltages

of 110 VAC or 230 VAC nominal. Refer to the computer's User Guide for details.

WARNING

DONOT operate in a wet, damp, or explosive environment.

WARNING

In case of software failure, turn off the laser source.

Rev A, December 16, 2016 Page 2

CM100 Chapter 2: Safety

Chapter 3 Description

Thorlabs' Entry-Level Upright Reflective Confocal Microscope is a complete single-channel system.

By eliminating signals that originate from outside the focal plane, confocal microscopy provides the

ability to acquire high resolution, optically sectioned images from within a thick sample. The CM100

supports reflected-light confocal imaging for viewing the surface structure of biological samples or

for inspection applications.

The CM100 has a 35 mm x 52 mm x 3 mm silver-coated mirror at the front of the scan path that

directs light from the scanners to the objective. In order to use this microscope for widefield as well

as confocal imaging, you can replace this mirror with a beamsplitter. The CM100 is designed to

provide a cost effective entry point to owning a modular confocal microscope that can be upgraded

to an advanced confocal microscope.

3.1. Features at a Glance

● Upright Microscope Based on the Cerna DIY Microscopy Platform

♦95 mm Dovetail on Rail Accepts Cerna Accessories

♦D1N Dovetail on Top of Scan Path for Cerna Widefield Imaging Modules

● Confocal Scan Path with Galvo-Galvo Scanners

● One Benchtop Excitation Laser (660 nm SMLaser)

● One Multialkali PMT (Photomultiplier Tube)

● Filter Set for Reflected-Light: One Beamsplitter, One Quarter-Wave Plate, and Two

Polarizers

● Rigid Stand Slide Holder on Manual XYStage, 1/2" Travel

● 20X Olympus Objective

● PC with DAQ and ThorImageLS®Software

3.2. Imaging Capabilities

● Full frame 4096 x 4096 Pixel Images (Uni-Directional Scan)

● 2 FPSfor 512 x 512 Pixel Bi-Directional Scans

● Galvo/Galvo Scan Head with 1.0 to 10 µs Pixel Dwell Times

● 796 µm x 796 µm Field of View (FN25)

Page 3 TTN118785-D02

CM100 Chapter 3: Description

Chapter 4 Getting Started

This section is provided for those interested in getting the Reflective Confocal Microscope up and

running quickly.

4.1. Unpacking and Inspection

Open the package, and carefully remove the CM100 and its accessories. Unpack the laser, Galvo-

Galvo Controller, PMT, computer, and monitor from their respective packages. The table lists the

standard accessories shipped with the device.

Name Quantity

Reflective Confocal Microscope 1

Rigid Stand on XY Translation Stage 1

20X Microscope Objective (RMS20X) 1

NIBreakout Box 1

K-Cube Stepper Driver (KST101) 1

K-Cube Power Supply (KPS101) 1

Laser (S1FC660) 1

Galvo/Galvo Controller (LSK-GG) 1

PMT (PMT1001/M) 1

Computer with Monitor, Keyboard, and Mouse 1

Clamping Fork (CF175) 1

Post Holder (PH082E) 1

Optical Post (TR20/M) 1

NI SHC68-68-EPM Cable 1

NI SH6868 Cable 1

Polarization-Maintaining Patch Cable (P1-630PM-FC-2) 1

Armored Fiber Patch Cable 1

Beamsplitter1(BSW10R) 1

Polarizers1(LPVISE100-A) 2

Quarter-Wave Plate (WPQ10E-670) 1

K-Cube USB Cable 1

SMA to BNC Cable 1

Alignment Tool 1

Rev A, December 16, 2016 Page 4

CM100 Chapter 4: Getting Started

Name Quantity

Grid Slide (R1L3S3P) 1

M6x16 mm Socket Head Cap Screw 12

1/4-20x5/8" Socket Head Cap Screw 12

M6 Flat Washer 6

2 mm Hex Wrench 1

2.5 mm Hex Wrench 1

3/32" Hex L-Key 1

3/16" Hex L-Key 1

1.5 mm Hex Wrench 1

5 mm Hex L-Key 1

2 mm Hex L-Key 1

1) The filter set comes pre-installed on the microscope.

Inspect the device and its accessories for any missing parts or damage. If there is any problem,

please contact our nearest office (see Thorlabs Worldwide Contacts Chapter on Page 25 for details).

4.2. Setting up the CM100

CAUTION

DO NOT place the SMA to BNC cable or DB-25 Connector cable near any electrical noise

sources such as a power cable.This may cause poor quality images.

A. Microscope

1. Use four screws (M6 for metric/1/4-20x5/8" for imperial) to mount the CM100 onto the optical

table.

See the Mechanical Drawing Chapter on Page 23 for mounting holes.

2. Use the 2 mm hex wrench to remove the shipping plate on the objective arm.

3. Use two screws and washers to mount the K-Cube Stepper Motor Controller onto the optical

table.

Page 5 TTN118785-D02

CM100 Chapter 4: Getting Started

4. Connect the cable from the Motorized Objective Arm to the Motor port of the K-Cube

Stepper Motor Controller.

5. Connect the K-Cube Power Supply to a standard power outlet.

6. Connect one end of the USB cable to the K-Cube Stepper Driver Controller and the other

end to the computer.

B. Computer

1. Setup the computer, monitor, keyboard, and mouse.

2. Connect one end (silver) of the NI SHC68-68-EPM cable to the computer (Connector 0) and

the other end (blue) to the rear panel of NI Breakout Box.

3. Connect one end of NI SH6868 cable to the NI Breakout Box and other end to the DAQ port

of Galvo/Galvo Controller.

C. Galvo-Galvo Controller

1. Connect the DB-25 Connector cable to the Scanner port of the Controller and the other end

to the Scanner Controller port of CM100.

2. Connect the power cord to a standard power outlet.

D. Laser

Read the Laser User Guide included along with the unit before setting up the laser.

WARNING

DO NOTswitch on the laser while installing the Confocal system. This may cause injury due

to laser radiation. Make sure the laser source is off.

1. Remove the red cap from the CM100 back panel.

2. Connect one end of the PM (Polarization-Maintaining) Patch cable to the laser and the other

end to the CM100 back panel.

Rev A, December 16, 2016 Page 6

CM100 Chapter 4: Getting Started

Make sure to align the key on the Patch cable connector with the key slot on the fiber

bulkhead before connecting the cable.

3. Connect the power cord to a standard power outlet.

E. PMT

1. Use the post holder and clamping fork to mount the PMT onto the optical table.

2. Connect the USB port to the computer.

3. Connect the SMAto BNC cable from the OUTport of the PMT to the AI1 port on the NI

Breakout Box.

4. Connect one end of the Armored Fiber Patch cable to the PMT and the other end to the

Pinhole port in the CM100.

Page 7 TTN118785-D02

CM100 Chapter 4: Getting Started

Otros manuales para CM100

Tabla de contenidos

Otros manuales de Microscopio de THORLABS

THORLABS

THORLABS Cerna Series Manual de usuario

THORLABS

THORLABS MLS203 Series Manual de usuario

THORLABS

THORLABS FS200 Manual de usuario

THORLABS

THORLABS Cerna CM501 Manual de usuario

THORLABS

THORLABS TLV-U-FF Manual de usuario

THORLABS

THORLABS CM100 Manual de usuario

THORLABS

THORLABS CM100 Manual de usuario

THORLABS

THORLABS CM201 Manual de usuario

THORLABS

THORLABS MFC1 Manual de usuario

THORLABS

THORLABS LDCCM Manual de usuario

THORLABS

THORLABS LEDD1 Manual de usuario

Manuales populares de Microscopio de otras marcas

Thermo Scientific

Thermo Scientific Nicolet iN10 Guía

National

National DC3-163 Manual de usuario

KERN Optics

KERN Optics OPE-1 Manual de usuario

OPTIKA MICROSCOPES

OPTIKA MICROSCOPES B-150D Manual de usuario

Prior

Prior Lux POL Manual de usuario

Opitec

Opitec Smartscoop 115615 Manual de usuario

KERN

KERN OPO-1 Manual de usuario

Topcon

Topcon SP-1P Manual de usuario

Motic

Motic PA43 Manual de usuario

Leica

Leica DVM5000 Guía del usuario

MshOt

MshOt MZ62 Manual de usuario

KERN Optics

KERN Optics OZR-5 Manual de usuario

VWR

VWR VisiScope 384 Series Manual de usuario

Nikon

Nikon ECLIPSE E200 POL Manual de usuario

Leica

Leica DI C800 Manual

ThermoFisher Scientific

ThermoFisher Scientific Continuµm Manual de usuario

ThermoFisher Scientific

ThermoFisher Scientific Continuµm Manual de usuario

Olympus

Olympus SZ61 Manual de usuario