Thermo Scientific 151R-AEV-TS Manual de usuario

ES Series Laboratory

Refrigerators User's Manual

Laboratory Refrigerator Range

Applicable models:

151R-AEV-TS

151R-AEW-TS

288R-AEV-TS

288R-AEW-TS

Contents

Intended Use and Special Warning 3

Before first use 3

Positioning of refrigerator 3

Transportation and moving of refrigerator 4

Energy saving tips 4

Important information 4

Product information 4

Product details 5

Controller overview 6

Viewing and resetting minimum and maximum temperatures 7

Changing the factory set point 8

Changing the temperature scale 8

Changing the remote alarm contacts 9

Alarms 10

Remote alarm contacts 10

Maintenance and Servicing 12

Defrosting 12

Cleaning 12

Reversing the door 13

Storage 14

Electrical Connection 15

Disposal 16

Troubleshooting 17

Warranty 18

Contact Information 18

Intended Use and Special Warning

This equipment is tested in compliance with established regulations and then shipped ready

for use. This equipment is intended for general purpose cold storage and is not to be used in

the presence of explosive gases or mixtures and / or close to sources with high magnetic or

electric fields. Not intended for flammable material storage.

If the equipment is used in a manner not specified by the manufacturer, the protection

provided by the equipment may be impaired.

Thank you for purchasing this ES Series cold storage equipment. Before you first use this

laboratory refrigerator please carry out the following actions:

•Check that the refrigerator has not been damaged in any way during transportation.

•If any damage is found it must be reported to your local dealer immediately

•Ensure all packaging has been removed, including cardboard, polystyrene and any

tape used to hold shelves in place for transportation.

•The refrigerator has been cleaned prior to despatch; however, we advise that it should

be cleaned using lukewarm water containing a mild detergent and a soft cloth.

•We recommend that the refrigerator should be left in an upright position for 24 hours

prior to switching on.

•This equipment is not intended for use by persons (including children) with reduced

physical, sensory or mental capabilities, or lack of experience and knowledge, unless

they have been given supervision or instruction concerning use of the equipment by a

person responsible for their safety.

•Children should not be allowed to play with the equipment.

Positioning and safely using your ES series refrigerator

•Warning to reduce the risk of the unit falling over, do not tip beyond 10 degrees

•Make sure the equipment is placed in a dry, well ventilated site, away from heat

sources.

•The equipment must be placed on a level surface. If necessary, adjust the feet on the

product so the equipment remains level during operation.

•The equipment should have sufficient clearance around it to provide adequate

ventilation – 10cm at each side, 6cm at the rear and 2.5cm at the top.

•Before ANY maintenance activity, pull the plug out of the socket by gripping the

plug, DO NOT pull on the plug cord.

•DO NOT use double-wire extension cords. If an extension cord is necessary make

sure it is a cord, which possess a protection safety certificate.

•If the main power supply cord is damaged, it should be replaced by a qualified service

engineer.

•DO NOT attempt any repairs to the equipment yourself (apart from those highlighted

in the Maintenance and Service Section). Repairs carried out by someone without the

relevant training are putting their personal safety at risk and will invalidate your

warranty.

•WARNING: this equipment is only to be operated by authorised personnel or

personnel who have correct knowledge on how the equipment operates.

Transporting and moving your ES series refrigerator

The refrigerator must always be moved in the vertical position. The cabinet must not be tilted

anymore than 10°. In the event that the cabinet is tilted more than 10°, the power supply must

not be connected until the equipment has stood upright for at least 24 hours.

Energy saving tips

This equipment is cooled by energy-efficient R600a refrigerant. To keep running costs as low

as possible always:

•Position the equipment away from heat sources.

•Make sure the air can circulate freely around the equipment, don’t block ventilation

grid.

•Ensure that products being stored are below room temperature upon entry.

•Make sure the door is opened as little as possible whilst in use and closed as quickly

as possible to prevent unnecessary temperature fluctuations.

Important Information

The refrigerator contains environment-friendly, non ozone depleting refrigerant R600a. As

R600a is a flammable gas, it is important to avoid damage to the refrigeration circuit during

transport and installation. If the refrigeration circuit is damaged, avoid using a naked flame in

the vicinity of the refrigerator and connecting power to the refrigerator. Also make sure there

is good ventilation in the room. If you are in doubt please contact your supplier.

– WARNING: Keep ventilation openings, in the equipment enclosure or in the built-in

structure, clear of obstruction.

– WARNING: Do not use mechanical devices or other means to accelerate the

defrosting process, other than those recommended by the manufacturer.

– WARNING: Do not damage the refrigerant circuit

Product Information

This refrigerator has been designed and built with the intention of the product being used

within a Laboratory and is designed to store contents between +1°C to +10°C.

Please see below for specific product information:

Model Height

(mm) Width

(mm) Depth

(mm) Weight

(Kg) Refrigerant

type Ambient/Room

working

temperature

No. of

shelves Door

Type

151R 845 595 635 36 R600a +10°C

+32°C

3Solid

288R 1565 595 670 58 3 Solid

Product details

1. Lock

2. Electronic Controller

3. Door Handle

4. Wire Shelf

5. Wire Basket

6. Adjustable foot (2 at front of equipment)

7. Door furniture

There are also 2 roller castors at the rear of the equipment to ease product movement.

Please contact your local representative for information on spare parts

1 2

6 7

Controller overview and operation

1. Menu

2. Lock keypad

3. Maximum temperature / Up

4. Power

5. Mute

6. Minimum temperature / Down

7. Set / Enter

1 2 3

45 6 7

Viewing & resetting minimum and maximum temperatures

Changing the factory set point

(the set point is the point at which the refrigerator normally holds the temperature at; in rare

circumstances such as high/low room temperatures it may be necessary to adjust this slightly.

Changing the factory setting is not recommended.)

Function Press Holdbutton(s)

downfor Examplescreen

Tochangethesetpoint 3seconds

followedby Once

followedby 1second

(currentsetpoint)

followedby /

(Increase/Decrease)

upto10times

followedby 1second

Note:setpointcanbeincreasedordecreasedin+/‐0.1°incrementsbyaMAXIMUMof1°C

Changing the temperature scale between Celsius (°C) and Fahrenheit (°F)

Function Press Holdbutton(s)

downfor Examplescreen

Tochangetemperaturescale 3seconds

followedby Twotimes

followedby 1second

(currentscale)

followedby /Once

followedby 1second

Changing the remote alarm contacts

Function Press Holdbutton(s)

downfor Examplescreen

Tochangethealarmcontactstate 3seconds

followedby Threetimes

followedby 1second

(currentstate)

followedby /Once

followedby 1second

Note:NO=NormallyOpen,NC=NormallyClosed

Warning Alarms

This refrigerator has been designed to provide both an audible and visual alarm should any of

the following situations occur:

•Door is left open for a set period

•Internal air temperature goes outside the set parameters, either too high or too low

•Internal ‘load’ temperature goes outside the set parameters, either too high or too low

Should one of these alarms occur this can be muted by pressing on the controller.

The ‘load’ temperature is a simulated temperature which is intended to provide an indication

of the temperature of the refrigerator’s contents (e.g. a 5ml sample). The temperature of a

refrigerator’s contents will change more slowly (up or down) than the air temperature within

that refrigerator should there be a fault or the door is left open.

Remote alarm contacts

All ES series laboratory refrigerators include remote alarm contacts and these terminal

contacts enable the user to connect to a remote control station; these contacts can be found on

the rear of the cabinet. WARNING: These contacts must only be accessed by a competent

electrician.

In order to use these contacts the following must be carried out:

1. The refrigerator MUST be disconnected from the power supply before removing the

terminal cover.

2. Unscrew the cover (figure 1) on the right hand side of the rear of the cabinet to expose

the connectors (figure 2).

3. Use the right hand outer positions that correspond to the left hand cable positions for

your connections using 0.75mm cable stripped to 0.6mm.

4. Depress the larger slot above the cable entrance on the right hand side with a small

electrical screwdriver. This allows the cable to be inserted into the slot directly below.

In the event of a door open alarm, high or low temperature alarm or power failure a remote

relay will switch within the controller to make an electrical circuit.

Figure 1 Figure 2

Este manual sirve para los siguientes modelos

Tabla de contenidos

Idiomas:

Otros manuales de Refrigerador de Thermo Scientific

Thermo Scientific

Thermo Scientific 263C-AEV-TS Manual de usuario

Thermo Scientific

Thermo Scientific MR05 Series Manual de usuario

Thermo Scientific

Thermo Scientific TSG Series Manual de usuario

Thermo Scientific

Thermo Scientific TSG Series Manual del propietario

Thermo Scientific

Thermo Scientific TSG400R Manual

Thermo Scientific

Thermo Scientific TSX2305SA Manual de usuario

Thermo Scientific

Thermo Scientific Jewett Pass-Thru BBR55D-2A Series Manual del propietario

Thermo Scientific

Thermo Scientific Jewett CT 1 Manual de usuario

Thermo Scientific

Thermo Scientific Fisher Scientific Isotemp 50FREEFSA Guía de inicio rápido

Thermo Scientific

Thermo Scientific TSX Series Manual del propietario

Thermo Scientific

Thermo Scientific TSG Series Manual de usuario

Thermo Scientific

Thermo Scientific ES Series Manual de usuario

Thermo Scientific

Thermo Scientific 18LCEETSA Manual de usuario

Thermo Scientific

Thermo Scientific Revco Manual de usuario

Thermo Scientific

Thermo Scientific 20LFEETSA Manual de usuario

Thermo Scientific

Thermo Scientific Fisher Scientific Isotemp 05FREEFSA Manual de usuario

Thermo Scientific

Thermo Scientific PLR 221 Manual de usuario

Thermo Scientific

Thermo Scientific TSX Series Manual del propietario

Thermo Scientific

Thermo Scientific 25LCEETSA Manual de usuario

Thermo Scientific

Thermo Scientific 05LRAETSA Manual de usuario

Thermo Scientific

Thermo Scientific TSX Series Manual del propietario

Thermo Scientific

Thermo Scientific REVCO Series Manual de usuario

Thermo Scientific

Thermo Scientific Harris MBF-700 Manual de usuario

Thermo Scientific

Thermo Scientific TSG Series Manual de usuario

Manuales populares de Refrigerador de otras marcas

Bonnet Neve

Bonnet Neve SKYVIEW PLUS Manual de usuario

Zanussi Electrolux

Zanussi Electrolux ZERB 8441 Manual de usuario

Sharp

Sharp SJ-BA31IEXW2-EU Manual de usuario

CORBERO

CORBERO CC2300MCW Manual de usuario

KitchenAid

KitchenAid 2205264 Manual de usuario

Stengel

Stengel KU 1101 A++ Manual de usuario

NEFF

NEFF KI181 Series Manual de usuario

Hoshizaki

Hoshizaki Reach-In Manual de usuario

Amana

Amana ASD2524VES00 Manual de usuario

BOMANN

BOMANN KGC 213 Manual de usuario

Danby

Danby DAR044A1SLDD Instrucciones de montaje

Samsung

Samsung RF323TE Manual de usuario

Beko

Beko CSA31022 Manual de usuario

IKEA

IKEA FROSTIG C 185 E Manual de usuario

Electrolux

Electrolux ER 6821 D Manual de usuario

True

True TS-28 Manual de usuario

Frigidaire

Frigidaire FSC23R5DW9 Manual de usuario

Beko

Beko LSP4579W Manual de usuario