The World Models Manufacturing Super Frontier Senior Manual de usuario

Wing Span

Wing Area

Flying Weight

Fuselage Length

80.5 in / 2040mm

1232 sq in / 79.5 sq dm

7.0 lbs / 3300g

65.5 in / 1670mm

Warning !This model is not a toy.

It is designed for maximum performance. Please seek advice if one is not familiar with this kind

of engine powered precision model. Operating this model without prior preparation may cause

injuries. Remember, safety is the most important thing. Always keep this instruction manual

at hand for quick reference.

0.46 cu. in. displacement 2-cycle

Radio required : 4 channel 5 servos - radio w/ standard

* Specifications are subject to change without notice.*

Specifications

INSTRUCTION MANUAL

Super

FACTORY PRE-FABRICATED

ALMOST-READY-TO-FLY (ARF) SERIES

MADE IN CHINA

A088PO25531103

The World Models

Manufacturing Co., Ltd.

www.theworldmodels.com

Super

INDEX

P. 3 - 11

ASSEMBLY

BEFORE YOU BEGIN

P. 1

SAFETY PRECAUTIONS

P. 11

BEFORE YOU BEGIN

Read through the manual before you begin, so you will have an overall idea of what to do.

Check all parts. If you find any defective or missing parts contact your local dealer. Please

DRY FIT and check for defects for all parts that will require CA or Epoxy for final assembly.

Any parts you find to be defective after the gluing process may be difficult to remove for

warranty replacement. The manufacturer will replace any defective parts, but will not extend

to the parts that are good before gluing to defective parts during assembly. Warranty will

not cover any parts modified by customer.

Symbols used throughout this instruction manual comprise of the following : -

PARTS LIST

P. 2

P.1

3mm

Do not overlook this symbol!

Cut off shaded portion.

Peel off shaded portion

covering film.

Pay close attention here!

Pierce the shaded portion

covering film.

Must be purchased separately!

Drill holes with the specified

diameter (here: 3mm).

Ensure smooth non-binding

movement while assembling.

Apply instant glue

(C.A.glue, super glue.)

Assemble left and right

sides the same way.

Apply epoxy glue.

Apply thread locker

Warning!

A088PO25531103

Parts List

1. MAIN WING -- 1 pair

2. SCREW PB2x20mm -- 4 pcs

FUEL TUBE Ø6x5mm -- 4 pcs

CLEVIS PL4112103 -- 2 pcs

STRAPER PL4112102 -- 2 pcs

HORN PL4113101 -- 2 pcs

PUSHROD Ø1.8x130mm w/ Threads (For Aileron Servo ) -- 2 pcs

3. WOODEN 12x22x346mm (Wing Joiner)(A) -- 1 set

WOODEN Ø10x180.5mm (Wing Joiner)(B) -- 1 set

4. STABILIZER & ELEVATOR -- 1 set

FUSELAGE -- 1 pc.

5. VERTICAL FIN & RUDDER -- 1 set

6. MAIN LANDING GEAR -- 1 set

MAIN WHEEL Ø95mm -- 2 pcs

COLLAR Ø4.1mm w/ set screw -- 4 sets

MOUNTING PLATE 12x20mm -- 2 pcs

SCREW PA 3x12mm -- 4 pcs

7. SOCKET HEAD SCREW M4x25mm -- 4 pcs

WASHER d4xD9mm --- 4 pcs

ENGINE MOUNT PL 5111050 -- 1 set

8. FUEL TANK 380cc PL1111380 -- 1 set

BALSA 10x15x117mm(For Fixing Fuel Tank) --1 pc.

9. SCREW PA3x14mm -- 4 pcs

STEERING ARM STAND Ø4.7mm -- 1 pc.

WOODEN 4x25x30mm (For Steering Arm Tank) --1 pc.

10. WIND SHIELD -- 1 pc.

SCREW PWA 2.3x8mm -- 5 pcs

SILICON GROMMET d1.5xD6.5mm -- 5 pcs

11. FRONT LANDING GEAR -- 1 set

FRONT WHEEL Ø95mm -- 1 pc.

COLLAR Ø4.6mm -- 3 set

STEERING ARM Ø4.6mm -- 1 set

RIGHT ANGLE WHEEL SPACER PL4121040 -- 1 set

12. SOCKET HEAD SCREW M3x30mm -- 4 pcs

WASHER d3xD7mm -- 8 pcs

M3 NUT -- 8 pcs

SPINNERØ52mm -- 1 set

THROTTLE PUSH WIRE Ø1.2x445mm -- 1 pc.

PLASTIC TUBE d2xD3x200mm -- 1 pc.

COVERING:--

LIGHTEX SGX 312 BRIGHT RED

LIGHTEX SGX 100 WHITE

LIGHTEX SGX 251 SKY BLUE

LIGHTEX SGX 351DARK BLUE

LIGHTEX SGX 313 PINK

LIGHTEX SGX 250 BLUE

P.2

13. SCREW PWA2.6x12mm -- 5 pcs

SILICON GROMMET d1.5xD6.5mm -- 5 pcs

COWLING -- 1 pc.

TRANSPARENT 3D TEMPLATE -- 1 pc.

14. SIDE WINDOWS -- 1pair

15. LINKAGE CONNECTOR Ø2.1mm HW7111060 -- 2 sets

16. SPONGE 60x70x122mm -- 1 pc.

FUEL TUBE Ø6x5mm -- 1 pc.

STRAPER PL4112102 -- 1 pc.

WIRE Ø1x1100mm(For Rudder) -- 2 pcs

COPPER TUBE Ø2.5xD3.2x8mm --2 pcs

RIGGING Z BEND Ø1.8x27mm(For Rudder) -- 2 pcs

FRONT WHEEL PUSHROD Ø1.6x320mm -- 1 pc.

PUSH ROD Ø1.8x1155mm w/ Threads (For Elevator Servo) -- 1 pc.

17. SCREW PB2x16mm -- 2 pcs

FUEL TUBE Ø6x5mm -- 1 pc.

CLEVIS PL4112103 -- 1 pc.

HORN PL4113101 -- 1 set

18. SCREW PM2x16mm -- 2 pcs

M2 NUT -- 2 pcs

FUEL TUBE Ø6x5mm -- 2 pcs

COPPER TUBE Ø2.5xD3.2x8mm --2 pcs

RIGGING COUPLER Ø1.8x27mm w/ Threads (For Rudder) -- 2 pcs

HORN (w/ o-Base For Rudder) PL4113101 -- 2 pcs

CLEVIS PL4112103 -- 2 pcs

19. PILOT PC001085B --1 set

PLYWOOD 3x45x122mm (For Pilot) -- 1 pc.

BALSA 6x6x45mm (For Pilot Stand) -- 2 pcs

20. SCREW PM3x30mm -- 2 pcs

WASHER d3xD12mm -- 2 pcs

PLYWOOD 3x40x120mm (For Wing Protection) --1 pc.

21. DECALS A088DEC -- 1 set

A088PO25531103

P.3

Main Wing

Wing Joiner(A)

12x22x346mm

Wing Joiner(B)

Ø10x180.5mm

1Main Wing

Ø1mm pilot holes for World Models tri-horn are pre-drilled.

Please look for pin-hole marks at under side of control surfaces.

Aileron Servo

PB2x20mm Screw

Pushrod

Ø1.8x130mm

Clevis Fuel Tube

Ø6x5mm

Aileron servo lead

Peel off shaded portion

covering film.

PB2x20mm

Horn

Bottom View

Pre-glued

1mm

TWM PL8210010

CLEVIS WRENCH

Please dry fit wing joiner into left and right wing to make sure they fit with the

proper dihedral angle, mark the wing joiner if necessary. Apply epoxy glue to

both sides of all surfaces in contact. Use a stick to apply the glue to inner side

of wing joiner sleeve, and apply the glue to wing joiner before putting them

together. Wing joiner not glued properly will lead to wing failure and plane crash.

A088PO25531103

P.4

Landing Gear

Vertical Fin / Rudder

A A'

A = A'

PA3x12mm Screw

3mm Set Screw

4.1mm Collar

3mm Set Screw

4.1mm Collar

Main Landing Gear

Ø4mm

PA3x12mm

C = C'

4Stabilizer

A A'

A = A'

(Stabilizer)

(Main Wing)

B B'

B=B'

Temporary install the main wing, adjust

leveling of the stabilizer to make it as

parallel to the main wing as possible.

Pre-glued

1.5mm

A088PO25531103

P.5

Bottom View

7Engine Mount

Engine Mount

PL5111050

M4x25mm Socket Head Screw

M4x25mm

Fuel Tank

380cc

Fuel Tank

Install Balsa 10x15x117mm

( )For Fuel Tank Position Fixing

Fuel Tank

380cc

Front Landing Gear

PA3x14mm Screw

PA3x14mm

Steering Arm Stand

d4xD9mm Washer

2mm

A088PO25531103

P.6

M3x30mm Socket Head Screw

M3 Nut

Engine

M3x30mm

Plastic Tube

d2xD3x200mm

Throttle Pushwire

Ø1.2x445mm

Install Engine position

Spinner

Ø52mm

105mm

4.13 in.

Front Wheel

3mm Set Screw

4.6mm Collar

Collar

4.6mm

Collar

4.6mm

Collar

4.6mm

10 Canopy

PWA2.3x8mm Screw

d1.5xD6.5mm Silicon Grommet

Silicon Grommet

d1.5xD6.5mm

PWA2.3x8mm PWA2.3x8mm

Right Angle Wheel Spacer

d3xD7mm Washer

1.5mm

M3 Nut

d3xD7mm

Washer

d3xD7mm

Washer

A088PO25531103

P.7

Windows

13 Cowling

PWA2.6x12mm Screw

d1.5xD6.5mm Silicon Grommet

Trim the cowling so it

will match your engine.

PWA2.6x12mm

51.5mm

Silicon Grommet

d1.5xD6.5mm

1.5mm

Fuel Filler

PL8110030

A088PO25531103

P.8

Elevator Pushrod

PB2x16mm Set Screw

Elevator Pushwire

Bottom View

Elevator Horn

Line up the holes

of the horn to the

edge of the elevator

See diagram.

Fuel Tube

Ø6x5mm

Horn

PB2x16mm

Ø1mm pilot holes for World

Models tri-horn are pre-drilled.

Please look for pin-hole marks

at under side of control surfaces.

Front Wheel

Radio Equipment

Install and arrange the servo as shown in the diagram.

Rudder

Servo

Straper

Fuel Tube

Ø6x5mm

Bottom View

Plywood

9x57x122mm

Servo Set

3 x 3mm Set Screw

Linkage Connector

M2 Nut

2mm Washer

Please refer to attached sheet for linkage connector installation.

Included with the radio Set.

Throttle Pushwire

3x3mm Set Screw

Throttle Servo.

2mm

Washer

M2 Nut

2mm

Washer

Charge Receptacles

KP0041300

TWM PL8210010

CLEVIS WRENCH

Copper Tube

Spong

60x70x122mm

Elevator

Servo

Throttle

Servo

Press down the center

1/3 portion

Copper Tube

Rigging Z Bend

Ø1.8 x 27mm

Front Wheel Pushrod

Ø1.6x320mm

A088PO25531103

P.9

Pilot

PC001085B

Balsa 6x6x45mm

Plywood 3x45x122mm

18 Rudder Pullwire

PM2x16mm Screw

M2 Nut

PM2x16mm

Ø1mm pilot holes for World Models tri-horn are pre-drilled. Please

look for pin-hole marks at side of control surfaces.

M2 Nut

2mm

TWM PL8210010

CLEVIS WRENCH

Clevis

Rigging Coupler

1.8 x 27mm

Ring

Fuel Tube

6 x 5mm

Copper Tube

A088PO25531103

Tabla de contenidos

Otros manuales de Juguete de The World Models Manufacturing