The Handy S.A.M.2 Manual de usuario

ITEM # 16900G - 16900O - 16900R - 16900B

1. Center load on table - 1000 lb. maximum.

2. Connect to 110 psi maximum shop air.

3. Keep safety bar in position at all times - except

when lowering.

4. Keep hands and tools from under carriage.

5. Do not mount table when in elevated position.

6. Do not ride vehicle onto lift.

7. Lift must be in the lowered position when moving.

8. Only trained persons should operate Air Lift.

9. The working area should be sufficiently lit.

10. Foot controller should be at least 3 feet away from

Air Lift during raising and lowering operation.

11. Recommended for indoor use only.

12. Tie-down straps must be used in conjunction with

the holes provided in the lift top.

S.A.M.2 1000 AIR LIFT

INSTRUCTIONS PARTS DRAWING PART LIST

UNPACKING AND SET-UP

1. Open carton, then remove ramp, drop panel and shipping boards.

2. CAREFULLY TURN TABLE UPRIGHT INTO OPERATING POSITION BEFORE REMOVING SHIPPING

CABLE RESTRAINT FROM SCISSOR MECHANISM.

3. Remove the two shipping bolts attaching rear drop panel to lift top. The bolts are located under drop

panel and lift top at each end.

4. Connect foot-operated air valve to 110 psi maximum air supply. The lift may be damaged and/or personal

injury may result if the pressure exceeds the maximum 110 psi rating.

5. Stand clear of lift table, and depress the UP side of foot valve to raise table.

6. To lower table, lift detent bar from safety latch and lower to next position or to floor.

7. To level front or rear drop panels: adjust set screws up or down through access holes in each corner of lift

top to gain level work platform. See print.

8. Slide front & rear drop panels into place and lift to lock in place at end of tube.

9. Insert ramp mounting tabs into slots at either end of table to mount ramp.

NOTE: If cycle vise is being installed, ramp must be mounted opposite the cycle vise.

OPERATION

1. Loads must be centered on table at all times. Table is rated for a maximum load of 1000 lbs.

2. Loads must be firmly positioned and secured on table at all times. Tie-down straps must be used

in conjunction with the holes provided in the lift top.

3. All moving parts have been lubricated at the factory and should be re-lubricated every 6 months to prevent

galling. Grease zerks are located at each end of frame pivot shaft and at

top ends of inside frame assembly.

4. Lightly oil cylinder rod when it becomes dry.

5. Squirt some oil through bleed hole in plate end of cylinder to lubricate piston and its seal every 6 months.

6. Pivot shaft set screws should be checked frequently to be sure they are tight. These are

located at the top end of the inside frame assembly.

OTHER OPTIONS AVAILABLE

Separate installation instructions included with each option.

14476

CV-17 CYCLEVISE–Used to stabilize motorcycle while on lift

16901

10” SIDE EXTENSIONS – ( 2) Expa nds width of lift to a full 48”

NOTE: READ ENTIRE MANUAL TO COMPLY WITH ALL SAFETY AND SERVICE PRECAUTIONS.

DEATH, PERSONAL INJURY AND/OR PROPERTY DAMAGE MAY OCCUR UNLESS INSTRUCTIONS

ARE FOLLOWED CAREFULLY.

PARTS DRAWING - PARTS LIST

Shop for other garage accessories on our website.

Tabla de contenidos

Otros manuales de Sistema de elevación de The Handy

The Handy

The Handy B.U.L. Manual de lista de piezas

The Handy

The Handy 16867G Manual de usuario

The Handy

The Handy OX 1800 Manual de usuario

The Handy

The Handy 16013G Manual de usuario

The Handy

The Handy 10738 Manual de usuario

The Handy

The Handy 10740G Manual de usuario

The Handy

The Handy 16000G Manual de usuario

The Handy

The Handy 21660 Manual de usuario

The Handy

The Handy 10740 Hoja de datos

The Handy

The Handy 16007G Manual de usuario

The Handy

The Handy S.A.M. 1000 Manual de usuario

The Handy

The Handy 14472G Manual de usuario

The Handy

The Handy 20707G Manual de usuario

The Handy

The Handy 16005G Manual de usuario

Manuales populares de Sistema de elevación de otras marcas

morse

morse 82H-124 Manual de usuario

Braun

Braun NL955 Series Manual de usuario

haacon

haacon 1889.10 Manual de usuario

Protekt

Protekt AT 252 Manual de usuario

R. Beck Maschinenbau

R. Beck Maschinenbau HS 600 Manual de usuario

Nova Technology International, LLC

Nova Technology International, LLC NAS Series Manual de usuario

Genie

Genie Z-60/34 Manual de usuario

Screen Technics

Screen Technics INTERFIT Vertical Up Lift Manual de usuario

Mortuary Lift

Mortuary Lift ULTIMATE 1000 Manual de usuario

Custom Equipment

Custom Equipment Hy-Brid 3 Series Manual de programación

Custom Equipment

Custom Equipment Hy-Brid Lifts 2 Series Manual de programación

Hy-Brid Lifts

Hy-Brid Lifts HB-P3.6 Manual de programación

BERG

BERG BeNomic EasyLeaf Manual de usuario

Powermate

Powermate LiftGate LG-3 Manual de usuario

Snorkel

Snorkel TM12 Series Manual de usuario

Terberg

Terberg OMNIDEKA Manual de usuario

Harmar Mobility

Harmar Mobility AL625 Instrucciones de funcionamiento

Rotary

Rotary SPO16 Manual de usuario