TFC Tower APUMP-HE Series Manual de usuario

EEI≤0.20

Energy-saving Pipeline Canned

Motor Pump

APUMP-HE Series

Installation and

Operation Manual

TFC Group LLP

Notes:

01. Read the installation manual 11. Some models are not suitable for

carefully before installation and drinking water.

use. 12. The liquid may be high-temperature

02. The manufacturer will not be liable and high-pressure; therefore, the

for any personal injury, pump liquid in the system must be

damage and other property completely drained or the shut-off

damage due to failure to comply valves on both sides must be

with safety warnings closed before moving and

dismantling the pump to prevent

a burn hazard.

03. The installers and operators must

comply with local safety regulations.

13. If removing the exhaust bolt, high-

temperature and high-pressure

liquid will be released. Measures

must be taken to safely contain

any released liquid.

04. The user must conﬁrm that only

qualiﬁed personnel with

professional certiﬁcation and

proﬁciency of this manual are

permitted to install and maintain this

product.

05. The pump is rated Ip44 and must not

be installed in a place that is damp or

may be splashed by water.

14. Ventilation must be ensured in

summer or high ambient

temperature conditions to avoid

condensation that may cause

electrical malfunctions.

06. For convenient access of

maintaince, a shut-off valve shall be

installed on each side of the pump

15. If there is a risk of frost damage,

install a frost protection thermostat,

or drain down the system in order

to avoid frost damage to the pump

body.

07. The power supply of the pump must

be disconnected before installation

andmaintainace.

08. For domestic hot water, copper or

stainless steel pump body shall be

used.

16. If the pump is left unused for a long

time, please close the pipe valve in

the inlet and outlet of the pump and

disconnect the power supply.

17. If the ﬂexible cord of cable is

damaged, it must be replaced by a

qualiﬁed person.

18. Please close the valve at the inlet of

the pump and disconnect power of the

pump immediately if overheating

10. Do not start the pump without

liquid.

APUMP-HE

09. In hard water areas use

appropriate water treatment

additives to prevent calcium

deposits, which can block

pipelines and / or the pump

impeller.

or abnormality of motor is detected, and contact your vendor or service center

immediately.

19. If problem cannot be addressed according to the manual, please close the valves

on the inlet and outlet of the pump immediately, cut off power supply and contact

your vendor or service center immediately.

20. This product shall be put in a place out of reach of children. After installation, take

an isolation measures to avoid access of children.

21. This product shall be stored in a dry, well ventilated and cool place under room

temperature.

Warning

Before installation, you must carefully read the installation

and operation manual. The installation and use of the

equipment must comply with local regulation and

applicable operation standards.

Warning

Those who have weak physical strength, react slowly

or lack experience and knowledge (including children) can

use this motor pump only under the monitoring and

direction of his/her safety personnel.

Caution

Note

Warning

Failure to comply with this safety instruction may lead to

personal injury!

Failure to comply with this safety instruction may lead to

equipment malfunction or damage!

Note or instruction for easy and safe operations.

1. Signs

APUMP-HE

magnet

2. General

2.1. The APUMP-HE circulation

pump is designed for use

in domestic heating and hot

water systems.

The product is most applicable to the

following systems:

system

·variable-temperature pipeline heat

supply system

·heat supply system with night mode

·HVAC system

· Industrial circulation system

domestic heating and domestic

water supply system

This pump is equipped with permanent-

motor and differential pressure

controller, capable of automatically &

continuously adjusting motor performance

to meet the actual needs of the system.

This pump is equipped with control

panel on the front for easy operation

by users.

stable and variable-ﬂow heat supply

2.2. Advantages

Easy installation and start-up

(

motor pump needs no adjustment

and can be readily started and

will adjust automatically to meet

the actual needs of the systems.

High-degree comfort

·Low operational noise of motor pump

and whole system.

·Provided with self adaptivc mode

AUTO

Initial setting). In most cases, the

APUMP-HE

3.1 Ambient Temperature

Ambient temperature: 0 40

3.2. Relative humidity(RH):

Max. humidity: 95%

3.3. Medium (liquid delivery) temperature

Liquid delivery temperature: +2℃110

To avoid condensation in control box and the stator, the temperature of liquid

pumped by the motor pump must be always higher than ambient temperature.

3.4. System Pressure

Maximum pressure 1.0MPa(10bar).

3.5. Degree of Protection

IP 44

3.6. Inlet Pressure

℃~+ ℃

~℃

Liquid Temperature

<85℃90℃110℃

Inlet Pressure

0.05bar 0.28bar 1bar

0.5m head 2.8m head

3.7. Pumping Liquid

The pumping liquid includes thin, clean, non-corrosive and non-explosive liquid

which shall not contain any solid particles, ﬁber or mineral oil, and the pump must

deﬁnitely not be used to pump inﬂammable liquid such as rapeseed oil and gasoline.

If the pump is used in a place with relatively high viscosity, the pump has lower

performance. So when choosing a pump, the viscosity of liquid must be taken into

account.

3. Operating Conditions

10m head

APUMP-HE

4.1.

pump case indicates the ﬂow direction of liquid through the pump.

·When installing the motor pump in the pipeline, the two gaskets supplied must be

installed at the inlet and outlet.

·During the installation, the motor pump shaft must be horizontal.

Installation

When installing APUMP-HE series circulation pump, the arrow on the motor

4. Installation

APUMP-HE

4.2. Position of Junction Box

4.3.

The junction box can be rotated in a step of 90°.

The procedures for changing the position of junction box are as follows:

1. Close the valves at the inlet and outlet and release the pressure;

2. Unscrew and remove the four socket head screws that fasten the pump body;

3. Rotate the motor to the required position and align the four screw holes;

4. Install the four socket head screws again and fasten them clockwise making

sure they are fully tightened;

Changing Position of Junction Box

APUMP-HE

5. Open the valves at the inlet and outlet.

Warning

Pumping liquid may be high-temperature and high-pressure;

therefore, the liquid in the system must be completely drained or the

valves on both sides of motor pump must be closed before removing

the socket head screws.

4.4. Thermal Insulation of Motor Pump Body

Limiting the heat loss of motor pump body and pipeline.

Motor pump body and pipeline should be thermally insulated

to reduce their heat loss.

Do not insulate or cover the junction box and control panel.

Caution

Note

APUMP-HE

5. Electrical Connection

APUMP-HE

Electrical connection and protection shall comply with

local codes and norms.

Warning

The motor pump must be earthed

The motor pump must be connected to an external power switch,

with 3mm minimum contact gap in both poles.

·Check if the supply voltage and frequency are the same as parameters indicated on the

nameplate of the motor pump.

·Connect the motor pump and power supply with the plug supplied together with the

pump.

·After the power is supplied, the indicator lamp on the control panel is ON.

APUMP-HE series circulation motor pump needs no protection from external motor.

APUMP-HE

Tabla de contenidos

Manuales populares de Bomba de agua de otras marcas

Neptun

Neptun NPHW 5500 Manual de usuario

Sensidyne

Sensidyne Gilian BDX-II Instrucciones de instalación y funcionamiento

Draper

Draper 47808 Manual de usuario

Trolla

Trolla 12820 Manual de usuario

Sunfab

Sunfab SVH Series Manual de usuario

WilTec

WilTec 50740 Manual de usuario

Fieldmann

Fieldmann FVC 5015 EK Manual de usuario

Everbilt

Everbilt EFSUB5-122HD Manual de usuario

Graco

Graco Husky 3300e Manual de usuario

esotec

esotec 101018 Manual de usuario

moyno

moyno 2000 CC Manual de usuario

Becker

Becker BASIC VASF 2.80/1-0.AC230 Manual de usuario

Sykes AmeriPumps

Sykes AmeriPumps GP100M Guía de solución de problemas

DUROMAX

DUROMAX XP WX Series Manual de usuario

BRINKMANN PUMPS

BRINKMANN PUMPS SBF550 Manual de usuario

Franklin Electric

Franklin Electric IPS Manual de usuario

Xylem

Xylem e-1532 Series Manual de usuario

Milton Roy

Milton Roy PRIMEROYAL Manual de usuario