TFA 98.1009 Manual de usuario

RADIO CONTROLLED PROJECTION CLOCK WITH DIGITAL THERMOMETER

Instructions manual

Cat. No. 98.1009

Thank you for choosing this instrument from TFA.

Before you using it

Please be sure to read the instruction manual carefully.

This information will help you to familiarise yourself with your new device, learn all of its functions and parts,

find out important details about its first use and how to operate it, and get advice in the event of faults.

Following the instruction manual for use will prevent damage to the device and loss of your statutory rights

arising from defects due to incorrect use.

We shall not be liable for any damage occurring as a result of not following these instructions.

Likewise, we take no responsibility for any incorrect readings and for any consequences which may

result from them.

Please take particular note of the safety advice!

Please keep this instruction manual for future reference.

Scope of delivery:

Projection clock

AC/DC power adaptor

Instruction manual

FIELD OF OPERATION AND ALL OF THE BENEFITS OF YOUR NEW INSTRUMENT

AT A GLANCE

DCF-77 Radio controlled time with manual setting option

24 hours time display (hour, minutes, seconds)

Time projection (hour and minute)

Projection with adjustable brightness and projection orientation possible

Calendar display (weekday, date, month)

Alarm setting with snooze function

Time zone (±9 hours)

Indoor temperature display in degree Celsius

LED back-light

For your safety:

The product is exclusively intended for the field of application described above. The product should

only Unauthorised repairs, modifications or changes to the product are prohibited.

The product be used as described within these instructions.

In order to ensure a good reception of the DCF signal, it is recommended to keep a distance of at least

60 cm between the device and the mains plug.

Caution! Risk of electrocution!

Plug the basic unit only into a socket installed in regulation manner and with a mains voltage of 230V!

The mains socket must be installed near the equipment and it must be easily accessible.

The basic unit and the mains adapter must not come into contact with water or moisture. Only suitable

for operation in dry interiors.

Do not use the unit if the housing or the mains adapter are damaged.

Keep the unit out of reach of persons (including children) who cannot fully appreciate the potential

risks of handling electrical equipment.

Pull the plug out of the socket immediately if any fault occurs or if the unit is not used for a lengthy

period.

Only use the supplied mains adapter.

First connect the lead to the basic unit and then insert the mains plug into the socket.

Do not pull the plug out of the socket by its lead.

Route the mains lead so that it does not come into contact with sharp-edged or hot objects.

Caution!

Risk of injury:

Keep the batteries and the instrument out of reach of children.

Batteries must not be thrown into the fire, short-circuited, taken apart or recharged. Risk of explosion!

Batteries contain harmful acids. Low batteries should be changed as soon as possible to prevent

damage caused by a leaking battery. Remove the batteries if you do not use the product for a lengthy

period. Never use a combination of old and new batteries together or batteries of different types. Wear

chemical-resistant protective gloves and glasses when handling leaked batteries.

! Important information on product safety!

Do not expose the instrument to extreme temperatures, vibration or shock.

Keep the instrument in a dry place.

BUTTONS:

The radio-controlled projection clock uses the following buttons:

SNOOZE : Activate or deactivate snooze function

Alarm snooze function

: Activate the projection brightness at the highest level

: Exit the setting modes

: Back-light-On

AL/HR : Enter alarm setting mode

: Activate or deactivate alarm

:Stop alarm and snooze function

: Set the hours andday

:Back-light-On

MODE/MIN :Enter manual time setting mode

: Toggle between indoor temperature, seconds, alarm time, and date display

: Enter time zone setting mode

: Set the minutes, weekday and month

: Stop alarm and snooze function

: Back-light-On

: Set the brightness level of the projection (in A/C power mode)

(4 levels: High, Medium, Low, OFF)

: Back-light On

: Project the image direction (can display 4 different orientations)

: Back-light On

(BRIGHTNESS

button)

(DIRECTION

button)

Projector lens

MODE/MIN button

AL/HR

button

Battery cover

SNOOZE

button

Adjustable projector

Brightness

button

Direction

button

Adapter socket

SETTING UP:

The Projection clock can be batteries operated or powered by the provided AC/DC adapter.

BATTERIES INSTALLATION

1. Open the battery cover at the back of the projection clock as indicated above.

2. Checking the correct polarization, insert 2 x AA, IEC LR6, 1.5V Alkaline batteries into the battery

compartment and replace the cover.

3. When the batteries are inserted, all the segments of the LCD will light up briefly and a “beep” will

sound. the Projection clock will now start receiving the DCF time signal. After approximate 3 to 5

minutes, the DCF time will be displayed.

4. If reception is not successful within approximately 7-10 minutes, the PRojection clock will attempt to

receive the signal in the next following hour.

Your projection clock is now operational.

Note:

If the batteries are used as the main power source:

1. Projected image brightness, alarm volume and back-light strength would be weaker.

Battery cover

Battery

compartment

2. Battery life time would be much less than 1 year.

TO USE THE PROJECTOR POWER ADAPTER

The unit comes with an adapter unit for using the projector for an extended period of time, such as

throughout the night.

To install the adapter:

Important!

Make sure that your household voltage is 230V! Otherwise your projection clock may be

damaged.

1. Connect the power adapter to a wall socket

2. Insert the adapter into the jack at the bottom of the clock

3. The projection clock will now start receiving the DCF time signal. After approximate 3 to 5 minutes, the

DCF time will be displayed.

4. If reception is not successful within approximately 7-10 minutes, the Projection clock will attempt to

receive the signal in the following hour.

Your Projection clock is now operational.

Note:

If the Projection clock is powered through the adapter, the projection will be constantly ON at the highest

brightness level unless the brightness level is manually changed to a lower brightness level afterwards. And

the brightness of the projection can be change accordingly to enhance the clarity of the projected time by

pressing the button.

If the Projection clock is battery operated, the projection will be ON at the highest brightness level only when

the SNOOZE button is pressed. The intensity of the brightness level of the projection cannot be changed. If

the SNOOZE is released, the projection will be turned OFF.

BATTERIES POWERED WITH THE USE OF AC/DC ADAPTER

If the Projection clock is first powered by batteries and the power adapter is subsequently used for extended

period of time, the main power source of the projection clock will switch to AC/DC power. The batteries will

then act as a backup power source in case of power failure.

TO RESET THE PROJECTION CLOCK

To reset the Projection clock to the factory default setting or in case of a malfunction, please remove all

batteries from the unit and unplug the AC/DC adapter from any power source. Wait at least for 3 minutes

before powering up the Projection clock again.

HOW TO USE THE PROJECTOR

The projector projects the current time onto a wall or ceiling, preferably within a darkened room. It can be

adjusted forwards and backwards 180º for maximum projection range. The projection image can also be

adjusted to 4 upright positions, each with a rotation of 90º.

To project the time onto a flat surface

1. Point the projection lens in the appropriate direction (max. distance of the projection is 2 meters)

2. Adjust the intensity of the projector light with the button

3. Adjust the projection image in an upright position with the button

Note:

The projector will only project the current time. It will not project the seconds, date or temperature

information.

RADIO CONTROLLED TIME:

The time base for the radio-controlled time is a Cesium Atomic Clock operated by the Physikalisch

Technische Bundesanstalt Braunschweig which has a time deviation of less than one second in every one

million years.

The time is coded and transmitted from Mainflingen near Frankfurt via frequency signal DCF-77 (77.5 khz)

and has a transmitting range of approximately 1,500 km. The Projection clock receives this signal and

converts it to show the precise time and so when within this range the received time is completely accurate.

Otros manuales para 98.1009

Tabla de contenidos

Manuales populares de Despertador de otras marcas

Steren

Steren CLK-210 Manual de usuario

COP-USA

COP-USA ALCDVR32-SL Manual de usuario

Philips

Philips HF3505/70 Manual técnico

Casio

Casio PQ-70 Manual de usuario

iHome

iHome IA63 Manual de usuario

Coopers

Coopers 9765 Manual de usuario

ANJANK

ANJANK AC-190 Guía

Sharper Image

Sharper Image 204050 Manual de usuario

Lumie

Lumie Zest Manual de usuario

Dexford

Dexford RCT200 Manual de usuario

Philips

Philips AJL303/37B Manual de usuario

RST

RST Q754 Manual de usuario

iHome

iHome iKT50 Manual de usuario

Sony

Sony dash HID-B7 Manual de usuario

SVINZ

SVINZ SCC009 Manual de usuario

Clas Ohlson

Clas Ohlson 918863 Manual de usuario

IKEA

IKEA FNURRA Manual de usuario

Timex

Timex T128 Manual de usuario