Texas Instruments UCC25640EVM-020 Manual de usuario

UCC25640EVM-020 Evaluation Module

User's Guide

Literature Number: SLUUBX3B

June 2019–Revised November 2019

WARNING

www.ti.com

2SLUUBX3B–June 2019–Revised November 2019

Submit Documentation Feedback

General Texas Instruments High Voltage Evaluation (TI HV EMV) User Safety Guidelines

Always follow TI's set-up and application instructions, including use of all interface components within their

recommended electrical rated voltage and power limits. Always use electrical safety precautions to help

ensure your personal safety and those working around you. Contact TI's Product Information Center

http://ti.com/customer support for further information.

Save all warnings and instructions for future reference.

WARNING

Failure to follow warnings and instructions may result in personal injury,

property damage or death due to electrical shock and burn hazards.

The term TI HV EVM refers to an electronic device typically provided as an open framed, unenclosed

printed circuit board assembly. It is intended strictly for use in development laboratory environments,

solely for qualified professional users having training, expertise and knowledge of electrical safety risks in

development and application of high voltage electrical circuits. Any other use and/or application are strictly

prohibited by Texas Instruments. If you are not suitable qualified, you should immediately stop from further

use of the HV EVM.

1. Work Area Safety:

a. Keep work area clean and orderly.

b. Qualified observer(s) must be present anytime circuits are energized.

c. Effective barriers and signage must be present in the area where the TI HV EVM and its interface

electronics are energized, indicating operation of accessible high voltages may be present, for the

purpose of protecting inadvertent access.

d. All interface circuits, power supplies, evaluation modules, instruments, meters, scopes, and other

related apparatus used in a development environment exceeding 50Vrms/75VDC must be

electrically located within a protected Emergency Power Off EPO protected power strip.

e. Use stable and non-conductive work surface.

f. Use adequately insulated clamps and wires to attach measurement probes and instruments. No

freehand testing whenever possible.

2. Electrical Safety:

As a precautionary measure, it is always good engineering practice to assume that the entire EVM

may have fully accessible and active high voltages.

a. De-energize the TI HV EVM and all its inputs, outputs and electrical loads before performing any

electrical or other diagnostic measurements. Revalidate that TI HV EVM power has been safely

de-energized.

b. With the EVM confirmed de-energized, proceed with required electrical circuit configurations,

wiring, measurement equipment hook-ups and other application needs, while still assuming the

EVM circuit and measuring instruments are electrically live.

c. Once EVM readiness is complete, energize the EVM as intended.

www.ti.com

SLUUBX3B–June 2019–Revised November 2019

WARNING

While the EVM is energized, never touch the EVM or its electrical

circuits, as they could be at high voltages capable of causing

electrical shock hazard.

3. Personal Safety

a. Wear personal protective equipment e.g. latex gloves or safety glasses with side shields or protect

EVM in an adequate lucent plastic box with interlocks from accidental touch.

Limitation for safe use:

EVMs are not to be used as all or part of a production unit.

4SLUUBX3B–June 2019–Revised November 2019

Submit Documentation Feedback

UCC25640EVM-020 Evaluation Module

User's Guide

SLUUBX3B–June 2019–Revised November 2019

UCC25640EVM-020 Evaluation Module

1 Introduction

The purpose of the UCC25640EVM-020 (EVM) is to aid in evaluation of the UCC256403 and UCC256404

LLC resonant controller. The EVM is a stand-alone LLC resonant half-bridge DC-DC power converter

designed to operate with DC input from 365 VDC to 410 VDC, AC input from 85 to 265 VRMS, 47 to 63 Hz,

and a nominal output of 12 VDC up to 180-W. The EVM is delivered using a diode rectifier at the output.

The user has the option to evaluate this converter with a synchronous rectifier (SR) by populating the

UCC24624 and SR FETs. This user’s guide provides basic evaluation instruction from a viewpoint of

system operation of the stand-alone LLC resonant power converter.

Figure 1. UCC25640EVM-020 Top View

Figure 2. UCC25640EVM-020 Side View

www.ti.com

Description

SLUUBX3B–June 2019–Revised November 2019

UCC25640EVM-020 Evaluation Module

2 Description

2.1 Typical Applications

• SMPS power supply for TV

• Industrial AC-DC adapters

• Power tools

• Medical power supply

• Multi-functional printer

• Enterprise and cinema projector

• PC power supply

• Gaming console power supply

• Lighting

2.2 Features

• Hybrid hysteretic controlled LLC resonant half-bridge DC-DC power conversion

• DC line Input from 365 VDC to 410 VDC

• AC Input voltage from 85 VDC to 265 VAC

• Regulated 12-VDC typical output

• Regulated 9.75-VDC low power mode output

• Full-load power of 180 W, or full-load current of 15 A

• High efficiency

• Optimized low power features enable extremely low standby power

• Advanced burst mode with burst soft-on and soft-off for minimized audible noise

• Adaptive dead-time

• X-capacitor discharge

• Over temperature, output over voltage, and three level over current protections

• Test points to facilitate device and topology evaluation

2.3 Using the EVM with UCC256402

• Replace U4 with UCC256402

• Replace R37 with 124kΩ

• Connect TP1 to TP14

• Disconnect the AC voltage source

2.4 Using the EVM with UCC256403

UCC25640EVM-020 comes populated with UCC256404. To use this EVM with UCC256403:

• Replace U4 with UCC256403

• Remove R5 and R28

• Replace R37 with 124 kΩ

• Remove C25

• Replace R57 with 1.07kΩ

• Replace C46 with 2.2nF

• Replace C36 with 33 nF

• Connect a 15 V DC source to TP6

• Disconnect the AC voltage source

Description

www.ti.com

6SLUUBX3B–June 2019–Revised November 2019

Submit Documentation Feedback

UCC25640EVM-020 Evaluation Module

2.5 Using the EVM with UCC24624 Synchronous Rectifier Controller

UCC25640EVM-020 is delivered using the diode rectifier at the output. The option to evaluate the

converter with synchronous rectification (SR) is available to the user. SR is often used to increase

efficiency by replacing the freewheeling diode with a lower loss FET.

To use this EVM with UCC24624:

• Remove D2 and D5

• Populate R31 and R32 with 0Ω

• Populate R35 with 10Ω

• Populate R53 and R54 with 532Ω

• Populate R55 with 39.2Ω

• Populate R2 and R7 with 10Ω

• Populate C2 and C19 with 1.2nF

www.ti.com

Performance Specifications

SLUUBX3B–June 2019–Revised November 2019

UCC25640EVM-020 Evaluation Module

3 Performance Specifications

Table 1. UCC25640EVM-020 Specifications

PARAMETER TEST CONDITIONS MIN TYP MAX UNITS

INPUT CHARACTERISTICS

DC voltage range 365 390 410 VDC

AC voltage range 85 265 VAC

AC voltage frequency 47 63 Hz

Input DC UVLO On 365 VDC

Input DC UVLO Off 330 VDC

OUTPUT CHARACTERISTICS

VOUT Output voltage - Normal mode Burst mode threshold to full load =

15 A 12 VDC

VOUT Output voltage - Standby mode No load to burst mode threshold 9.75 VDC

Burst mode threshold output

current limit (rising) 240 mA

Burst mode threshold output

current limit (falling) 110 mA

IOUT Output load current 365 to 410 VDC 15 A

Output voltage ripple 390 VDC and full load = 15 A 120 mVpp

SYSTEM CHARACTERISTICS

Resonant frequency 100 kHz

Peak efficiency 390 VDC, load = 8 A 93%

Operating temperature Natural convection 25 ºC

Schematic Diagram

www.ti.com

8SLUUBX3B–June 2019–Revised November 2019

Submit Documentation Feedback

UCC25640EVM-020 Evaluation Module

4 Schematic Diagram

Figure 3. UCC25640EVM-020 Power Stage Schematic

www.ti.com

Schematic Diagram

SLUUBX3B–June 2019–Revised November 2019

UCC25640EVM-020 Evaluation Module

Figure 4. UCC25640EVM-020 Control Schematic

Test Setup

www.ti.com

10 SLUUBX3B–June 2019–Revised November 2019

Submit Documentation Feedback

UCC25640EVM-020 Evaluation Module

5 Test Setup

5.1 Test Equipment

DC Voltage Source: Capable of 365 VDC to 410 VDC, adjustable, with minimum power rating 500 W, or

current rating not less than 1 A, with current limit function. The DC voltage source to be used should meet

IEC 60950 reinforced insulation requirement.

AC Voltage Source: Capable of single-phase output AC voltage 85 to 265 VAC, 47 to 63 Hz, adjustable,

with minimum power rating 100 W and current limit function. The AC voltage source to be used should

meet IEC 60950 reinforced insulation requirement.

DC Digital Multimeter: One unit capable of 0-VDC to 450-VDC input range, four digit display preferred;

and one unit capable of 0-VDC to 20-VDC input range, four digit display preferred.

Output Load: : DC load capable of receiving 0 VDC to 20 VDC, 0 A to 15 A, and 0 W to 300 W or

greater, with the capability to display information such as load current and load power.

Oscilloscope: Capable of 500-MHz full bandwidth, digital or analog: if digital, 5 Gsps, or better.

Fan: 200 to 400 LFM forced air cooling is recommended, but not required.

Recommended Wire Gauge: Capable of 25 A, or better than #14 AWG, with the total length of wire less

than 8 feet (4 feet input and 4 feet return).

Otros manuales de Placa madre de Texas Instruments

Texas Instruments

Texas Instruments LM25066EVK Manual de usuario

Texas Instruments

Texas Instruments TPS54JA20EVM-023 Manual de usuario

Texas Instruments

Texas Instruments TUSB1064RNQ Manual de usuario

Texas Instruments

Texas Instruments TVP9900EVM Manual de usuario

Texas Instruments

Texas Instruments UCC29950EVM-631 Manual de usuario

Texas Instruments

Texas Instruments LMK048 Series Manual de usuario

Texas Instruments

Texas Instruments TSW12D1620 Manual de usuario

Texas Instruments

Texas Instruments MSP432E411Y-BGAEVM Manual de usuario

Texas Instruments

Texas Instruments bq24153A Manual de usuario

Texas Instruments

Texas Instruments SCAU020 Manual de usuario

Texas Instruments

Texas Instruments TPS6236 EVM-655 Series Manual de usuario

Texas Instruments

Texas Instruments LM25088 Manual de usuario

Texas Instruments

Texas Instruments TCA6507EVM Manual de usuario

Texas Instruments

Texas Instruments DAC8554EVM Manual de usuario

Texas Instruments

Texas Instruments TPL0401EVM Manual de usuario

Texas Instruments

Texas Instruments PGA855 Manual de usuario

Texas Instruments

Texas Instruments TPS40400EVM-351 Manual de usuario

Texas Instruments

Texas Instruments eFuse TPS25983EVM Manual de usuario

Texas Instruments

Texas Instruments LP8755EVM Manual de usuario

Texas Instruments

Texas Instruments CC112 Series Manual de usuario

Texas Instruments

Texas Instruments TPL0501EVM Manual de usuario

Texas Instruments

Texas Instruments EK-TM4C123GXL Manual de usuario

Texas Instruments

Texas Instruments TPS23861EVM-612 Manual de usuario

Texas Instruments

Texas Instruments TL16C750EEVM Manual de usuario

Manuales populares de Placa madre de otras marcas

DFI

DFI SD170 Manual de usuario

ASROCK

ASROCK ROMED8-2T Manual de usuario

Asus

Asus P2L97A Manual de usuario

Winmate

Winmate IC70 Manual de usuario

Asus

Asus MES-B Manual de usuario

Grantech

Grantech SYS8F377VGGA-3OMN Manual de usuario

Telit Wireless Solutions

Telit Wireless Solutions SL869-3DR Manual de usuario

Gigabyte

Gigabyte GA-9IVDT Manual de usuario

Commell

Commell MS-C73 Manual de usuario

IBT Technologies

IBT Technologies MB860 Manual de usuario

Nvidia

Nvidia TEGRA DG-04927-001_V01 Manual de usuario

Biostar

Biostar M7VIT Bravo Instrucciones de funcionamiento e instalación

Intel

Intel D33217CK Manual de usuario

Asus

Asus F1A55-M LX PLUS R2.0 Manual de usuario

EPC

EPC EPC9147C Manual de usuario

Asus

Asus EX-B760M-V5 D4 Manual de usuario

EPOX

EPOX MU-8KHA0010 Manual de usuario

Ski-Doo

Ski-Doo Bombardier MPEM 219 700 090 Manual de usuario