Texas Instruments TUSB7340 Manual de usuario

TUSB7320/TUSB7340 EVM User's Guide

User's Guide

Literature Number: SLLU146B

May 2011–Revised August 2012

Contents

1 Introduction ........................................................................................................................ 5

2 EVM Board ......................................................................................................................... 6

1 TUSB7320 and TUSB7340 DEMO Boards ............................................................................... 6

2 Hardware Setup .................................................................................................................. 8

2.1 Headers ................................................................................................................... 8

2.2 VBUS ...................................................................................................................... 8

2.3 PCI Express Slot Options .............................................................................................. 8

3 Bringup .............................................................................................................................. 9

4 WAKE Testing Setup .......................................................................................................... 10

5 SMI Support ...................................................................................................................... 11

6 Schematics ....................................................................................................................... 12

1 TUSB7320 DEMO EVM REVB Schematics ............................................................................. 13

2 TUSB7340 DEMO EVM REVB Schematics ............................................................................. 17

Appendix A Bill of Materials ........................................................................................................ 21

2Table of Contents SLLU146B–May 2011–Revised August 2012

Submit Documentation Feedback

www.ti.com

List of Figures

1 TUSB7320 DEMO EVM REVB............................................................................................ 6

2 TUSB7340 DEMO EVM REVB............................................................................................ 7

3 SMI via Location for TUSB7340 DEMO EVM REVB ................................................................. 11

List of Tables

1 TUSB7320 DEMO REVB BOM ......................................................................................... 21

2 TUSB7340 DEMO REVB BOM ......................................................................................... 22

SLLU146B–May 2011–Revised August 2012 List of Figures

www.ti.com

This guide is intended to describe the necessary information needed to operate either the TUSB7320

DEMO EVM REVB or TUSB7340 DEMO EVM REVB boards. In this document you will find how to setup

and use the EVM boards. The schematics and bill of materials are also detailed at the end of the

document.

4List of Tables SLLU146B–May 2011–Revised August 2012

Submit Documentation Feedback

SLLU146B–May 2011–Revised August 2012

Introduction

The TUSB7340 is a USB 3.0 xHCI 0.96 compliant host controller that supports up to four downstream

ports. The TUSB7320 supports up to two downstream ports. The TUSB73x0 interfaces to the host system

via a PCIe x1 Gen 2 interface and provides SuperSpeed, High-speed, Full-speed, or Low-speed

connections on the downstream USB ports.

SLLU146B–May 2011–Revised August 2012 Introduction

PORT1

PORT2 J2

J26J27

J22

J40

SLLU146B–May 2011–Revised August 2012

EVM Board

1 TUSB7320 and TUSB7340 DEMO Boards

The TUSB7320 and TUSB7340 DEMO boards are both PCI Express X1 Standard Height cards. The

dimensions of both boards are 4.376 inches by 2.571 inches. The two figures below depict how the boards

look.

Figure 1. TUSB7320 DEMO EVM REVB

6EVM Board SLLU146B–May 2011–Revised August 2012

Submit Documentation Feedback

PORT3

PORT1

PORT2

PORT4

J26J27

J22

J40

www.ti.com

TUSB7320 and TUSB7340 DEMO Boards

Figure 2. TUSB7340 DEMO EVM REVB

SLLU146B–May 2011–Revised August 2012 EVM Board

Hardware Setup

www.ti.com

2 Hardware Setup

2.1 Headers

The EVM boards are populated with three headers: J22, J26, and J40.

J22 header is used to change the state of AUX_DET signal to the TUSB73XX. By default, this header is

not shorted and therefore AUX_DET will be high. If a jumper shunt is placed over J22, the AUX_DET will

be low.

The J26 header is used to route 5 V from the IDE Power Connector (J5) to the Texas Instruments

TPS2560 USB power switch. This header should always have a Jumper Shunt populated. For more

information on the Texas Instruments TPS2560, please visit www.ti.com.

J40 header is used to select the 3.3-V power source for the TUSB73X0. By default, a Jumper Shunt

should be populated across pins 1 and 2 of J40. When in this position, the 3.3-V power from the PCI

Express slot is routed to the TUSB73X0. If the Jumper Shunt is moved to pins 2 and 3, then the 3.3-V

VAUX power from the PCI Express slot is routed to the TUSB73X0. The Jumper Shunt should only be

moved to positions 2 and 3 if wake testing is required. Otherwise the jumper should be left in the default

position of 1 and 2.

NOTE: The 3.3-V VAUX power supply has a limited current capability. According to the PCI Express

Electromechanical Spec, the 3.3-V VAUX will have a maximum current of 375 mA. Because

of the limited current of 3.3-V VAUX, it is recommended to plug only one device into the

TUSB73X0. If the Jumper Shunt is left on pins 1 and 2 of J40, this current limitation does not

exist and therefore all ports of the TUSB73X0 can be used.

2.2 VBUS

VBUS for all of the USB ports comes from the IDE Power Connector (J5).

2.3 PCI Express Slot Options

Because the TUSB73X0 EVM boards are PCI Express X1, they can be used in any PCI Express Slot

(X1, X4, X8, or X16) on a typical motherboard. The boards can be used in either a PCI Express Gen1

(2.5 Gbps) or Gen2 (5 Gbps) slot. Because of the speed of USB3 (5 Gbps), if used in a PCI Express

Gen1 slot, the performance of the TUSB7320 or TUSB7340 will be negatively impacted. For this reason, it

is recommended to always insert the EVM board into a PCI Express Gen2 slot.

8EVM Board SLLU146B–May 2011–Revised August 2012

Submit Documentation Feedback

SLLU146B–May 2011–Revised August 2012

Bringup

Below are the steps to bring up the EVM board in a typical system:

1. Remove the power plug from the PC power supply.

2. Make sure the Jumper Shunts are populated on J26 and J40.

3. Insert the EVM board into a PCI Express slot. It is recommended to use a PCI Express Gen2 slot if

one is available.

4. Insert an IDE Power Connector into J5 of the EVM board.

5. Insert the power plug into the PC power supply.

6. Turn the PC on. Once the PC is turned on, all of the green LEDs should be ON. If LED D5 is not

active, please check to make sure the jumper shunt on J40 is populated. If none of the green LEDs

(D1 thru D4) for each USB Port are active, please check to make sure the Jumper Shunt on J26 is

populated and an IDE Power connector is plugged into J5.

7. Once the PC has booted into Windows 7, you will need to install the TI xHCI driver. If the driver has

already been installed on your PC, then you can proceed step 8. Otherwise, you will need to install the

xHCI driver by running the TI xHCI driver setup utility.

8. You can now insert devices into the USB ports.

SLLU146B–May 2011–Revised August 2012 Bringup

SLLU146B–May 2011–Revised August 2012

WAKE Testing Setup

The EVM board can be used to test the WAKE functionality of the TUSB73X0. By default, the EVM is not

configured to support wake testing. Please configure the EVM according to the following if WAKE is

required:

1. Move the Jumper Shunt on J40 to pins 2 and 3.

2. Make sure there is no Jumper Shunt on J22.

3. Use a dedicated 5-V power supply for VBUS. Do NOT use the IDE Power connector provided from the

system power supply. The reason for not using the IDE power from system power supply is when the

system is put in a sleep or hibernate state, the power on the IDE Power connector will be turned off.

NOTE: For some motherboards, WAKE from a PCIe slot is not supported or is only supported on

PCIE X1 slots. Please make sure to use a motherboard that supports WAKE from any PCIe

slot.

10 WAKE Testing Setup SLLU146B–May 2011–Revised August 2012

Submit Documentation Feedback

Este manual sirve para los siguientes modelos

Tabla de contenidos

Otros manuales de Placa madre de Texas Instruments

Texas Instruments

Texas Instruments THS4150 Manual de usuario

Texas Instruments

Texas Instruments VCA8613EVM Manual de usuario

Texas Instruments

Texas Instruments BQ24150 Manual de usuario

Texas Instruments

Texas Instruments TRF4903 Manual de usuario

Texas Instruments

Texas Instruments DS90UB954-Q1EVM Manual de usuario

Texas Instruments

Texas Instruments AFE7070 Manual de usuario

Texas Instruments

Texas Instruments TLV320AIC20KEVM Manual de usuario

Texas Instruments

Texas Instruments Track bq27520EVM Manual de usuario

Texas Instruments

Texas Instruments C2000 F28003x Series Manual de usuario

Texas Instruments

Texas Instruments DAC161S055EVM Manual de usuario

Texas Instruments

Texas Instruments DAC161S997 Manual de usuario

Texas Instruments

Texas Instruments TPS53015EVM-126 Manual de usuario

Texas Instruments

Texas Instruments TPS65313-Q1 Manual de usuario

Texas Instruments

Texas Instruments bq25040 Manual de usuario

Texas Instruments

Texas Instruments bq77905 Manual de usuario

Texas Instruments

Texas Instruments TRS3122EEVM Manual de usuario

Texas Instruments

Texas Instruments DP83869 Manual de usuario

Texas Instruments

Texas Instruments TPS7A53EVM-080 Manual de usuario

Texas Instruments

Texas Instruments TRF6900 Manual de usuario

Texas Instruments

Texas Instruments TPS60120EVM-174 Manual de usuario

Texas Instruments

Texas Instruments Chipset TRF2436EVM Manual de usuario

Texas Instruments

Texas Instruments AN-1502 LP5526 Manual de usuario

Texas Instruments

Texas Instruments DACx760EMC-EVM Manual de usuario

Texas Instruments

Texas Instruments OPT3001EVM Manual de usuario

Manuales populares de Placa madre de otras marcas

DFI

DFI SD170 Manual de usuario

ASROCK

ASROCK ROMED8-2T Manual de usuario

Asus

Asus P2L97A Manual de usuario

Winmate

Winmate IC70 Manual de usuario

Asus

Asus MES-B Manual de usuario

Grantech

Grantech SYS8F377VGGA-3OMN Manual de usuario

Telit Wireless Solutions

Telit Wireless Solutions SL869-3DR Manual de usuario

Gigabyte

Gigabyte GA-9IVDT Manual de usuario

Commell

Commell MS-C73 Manual de usuario

IBT Technologies

IBT Technologies MB860 Manual de usuario

Nvidia

Nvidia TEGRA DG-04927-001_V01 Manual de usuario

Biostar

Biostar M7VIT Bravo Instrucciones de funcionamiento e instalación

Intel

Intel D33217CK Manual de usuario

Asus

Asus F1A55-M LX PLUS R2.0 Manual de usuario

EPC

EPC EPC9147C Manual de usuario

Asus

Asus EX-B760M-V5 D4 Manual de usuario

EPOX

EPOX MU-8KHA0010 Manual de usuario

Ski-Doo

Ski-Doo Bombardier MPEM 219 700 090 Manual de usuario