Texas Instruments SmartRF CC900DBK Manual de programación

Tabla de contenidos

Otros manuales de Placa madre de Texas Instruments

Texas Instruments

Texas Instruments TPS8125 EVM Series Manual de usuario

Texas Instruments

Texas Instruments TPS543620 Manual de usuario

Texas Instruments

Texas Instruments LMR36506MSCEVM Manual de usuario

Texas Instruments

Texas Instruments LMR36503RFEVM Manual de usuario

Texas Instruments

Texas Instruments UCC28600 Manual de usuario

Texas Instruments

Texas Instruments LM5175RHFEVM-HD Manual de usuario

Texas Instruments

Texas Instruments TPS70151 Series Manual de usuario

Texas Instruments

Texas Instruments TPS7B81EVM-025 Manual de usuario

Texas Instruments

Texas Instruments TPA2050D4EVM Manual de usuario

Texas Instruments

Texas Instruments bq76PL536PGM-1 Manual de usuario

Texas Instruments

Texas Instruments DRV8846EVM Manual de usuario

Texas Instruments

Texas Instruments INA281EVM Manual de usuario

Texas Instruments

Texas Instruments DEM-OPA-MSOP-1B Manual de usuario

Texas Instruments

Texas Instruments DRV814x-Q1EVM Manual de usuario

Texas Instruments

Texas Instruments SD034EVK Manual de usuario

Texas Instruments

Texas Instruments TPS3899EVM Manual de usuario

Texas Instruments

Texas Instruments DRV8847 Series Manual de usuario

Texas Instruments

Texas Instruments LMK048 Series Manual de usuario

Texas Instruments

Texas Instruments TMAG5110-5111EVM Manual de usuario

Texas Instruments

Texas Instruments LP5813EVM Manual de usuario

Texas Instruments

Texas Instruments bq27750EVM Manual de usuario

Texas Instruments

Texas Instruments DRV8889-Q1EVM Manual de usuario

Texas Instruments

Texas Instruments DRV2605LDGSEVM-M Manual de usuario

Texas Instruments

Texas Instruments DAC53701EVM Manual de usuario

Manuales populares de Placa madre de otras marcas

DFI

DFI SD170 Manual de usuario

ASROCK

ASROCK ROMED8-2T Manual de usuario

Asus

Asus P2L97A Manual de usuario

Winmate

Winmate IC70 Manual de usuario

Asus

Asus MES-B Manual de usuario

Grantech

Grantech SYS8F377VGGA-3OMN Manual de usuario

Telit Wireless Solutions

Telit Wireless Solutions SL869-3DR Manual de usuario

Gigabyte

Gigabyte GA-9IVDT Manual de usuario

Commell

Commell MS-C73 Manual de usuario

IBT Technologies

IBT Technologies MB860 Manual de usuario

Nvidia

Nvidia TEGRA DG-04927-001_V01 Manual de usuario

Biostar

Biostar M7VIT Bravo Instrucciones de funcionamiento e instalación

Intel

Intel D33217CK Manual de usuario

Asus

Asus F1A55-M LX PLUS R2.0 Manual de usuario

EPC

EPC EPC9147C Manual de usuario

Asus

Asus EX-B760M-V5 D4 Manual de usuario

EPOX

EPOX MU-8KHA0010 Manual de usuario

Ski-Doo

Ski-Doo Bombardier MPEM 219 700 090 Manual de usuario

SWRU063

Quick Start Instructions

Rev. 1.1

SmartRF

®

CC900DBK Demonstration Board Kit

SWRU063 Page 2 of 2

How to get a quick start using CC900DBK

The CC900DBK Demonstration Board Kit demonstrates the CC900 RF transceiver in a very

simple application. The Demonstration Board includes a complete CC900 transceiver, an

AVR micro-controller, an integrated PCB antenna and a battery. It provides a complete

example of a low-cost, low-power system using the CC900 transceiver. Please note that the

design is optimised for low cost applications and not for maximum range. In order to evaluate

range and performance, use the CC900DK.

Important:

•Do NOT short-circuit the battery terminals at any time.

•The use of radio transceivers is regulated by international and national rules. Before

transmitting a RF signal, please contact your local telecommunication authorities to check

if you are licensed to operate the transceiver.

To get the Kit up and running, follow these steps:

1. The CC900DB runs off a 3.6V Lithium battery. If the battery is not mounted, solder it to

the pads at the rear side of the board.

2. Examine the LED. If it does not blink at regular intervals, push the “ON” button.

3. If the LED still does not blink, remove the battery and reconnect it. If this does not help,

exchange the battery with a new one.

4. Press the “ON” buttons on both Demonstration Boards so that both are blinking. They are

now in polling reception mode, checking for data each time the LED is lit.

5. Press the “TX” button on one of the boards. The demonstration board sends a data

packet of approximately 1.5 second duration.

6. If the other demonstration board received the message without errors, its LED will blink

the Morse code for “victory”. It then sends an acknowledgement message in return.

7. If the first board receives the acknowledgement message, it will also blink “victory” in

Morse code.

If a demonstration board has not received a message or had any buttons pressed for two

minutes, it will enter power-down mode, ensuring minimum power consumption. To wake it,

press the “On” button.

If communication does not succeed on the first attempt, try again. RF noise may have

corrupted the message. Signal processing in the small micro-controller has been kept to a

minimum, therefore a small noise burst may corrupt the message. When holding the

demonstration board, do not touch the antenna or the VCO tank. Ideally, keep your hand as

far away from the antenna as possible in order to get the best performance. If you wish to

reprogram the Demonstration Board using the Development Kit, make sure to:

•Use the cable supplied in the Development Kit

•Remove the battery when reprogramming

•Use the correct parallel port. If you are using the correct port, you will receive an error

message if you try to program the EEPROM and no Demonstration Board is inserted

For further information, see the CC900DB Demonstration Board User Manual, which can be

downloaded from our website (http: www.chipcon.com)