Texas Instruments MMWAVE-DEVPACK Manual de usuario

SWRU506–May 2017

MMWAVE-DEVPACK

User's Guide

SWRU506–May 2017

MMWAVE-DEVPACK

Contents

1 Getting Started............................................................................................................... 3

1.1 Introduction .......................................................................................................... 3

1.2 Kit Contents.......................................................................................................... 3

2 Hardware...................................................................................................................... 4

2.1 Block Diagram....................................................................................................... 6

2.2 Connecting the mmwave Sensor BoosterPack to the DevPack.............................................. 6

2.3 Power Connections................................................................................................. 7

2.4 Connectors .......................................................................................................... 8

2.5 PC Connection..................................................................................................... 10

2.6 Jumpers and LEDs ............................................................................................... 11

2.7 Design Files and Software Tools................................................................................ 12

3 Interfacing With Other Platforms ......................................................................................... 12

3.1 Radar Studio Interface............................................................................................ 12

3.2 Interfacing With the High-Speed Data Capture Platform: TSW1400 EVM ................................ 14

List of Figures

1 EVM Front View.............................................................................................................. 4

2 EVM Rear View.............................................................................................................. 5

3 Block Diagram................................................................................................................ 6

www.ti.com

2SWRU506–May 2017

Submit Documentation Feedback

MMWAVE-DEVPACK

MMWAVE-DEVPACK (continued)

4 Example BoosterPack Connection with DevPack....................................................................... 7

5 VBUS LED (DS6) and 3V3 LED (DS7) ................................................................................... 7

6 20-Pin BoosterPack Connectors........................................................................................... 8

7 60-Pin HD Connector ....................................................................................................... 8

8 120-Pin TSW EVM Interface Connector.................................................................................. 9

9 MIPI 60-Pin JTAG Connector.............................................................................................. 9

10 TI 14-Pin JTAG Connector................................................................................................ 10

11 Uninstalled Devices........................................................................................................ 10

12 COM Ports After the Driver Installation.................................................................................. 11

13 MUX Select Jumpers ...................................................................................................... 11

14 LEDs ......................................................................................................................... 12

15 MUX Control Jumpers..................................................................................................... 13

16 Example DevPack–BoosterPack Connection .......................................................................... 14

17 Device Manager............................................................................................................ 14

18 TSW1400 Connection – Front View ..................................................................................... 15

19 TSW1400 Connection – Rear View...................................................................................... 15

20 Connecting the mmWave DevPack...................................................................................... 16

List of Tables

1 LEDs ......................................................................................................................... 12

Trademarks

Windows is a registered trademark of Microsoft Corporation.

www.ti.com

Getting Started

SWRU506–May 2017

MMWAVE-DEVPACK

1 Getting Started

1.1 Introduction

The MMWAVE-DEVPACK is an add-on board used with TIs mmwave sensor EVMs (1243BOOST,

1443BOOST, and 1642BOOST) to provide more interfaces and PC connectivity to the mmwave sensor

EVM. It provides an interface for the Radar Studio tool to configure the Radar device and capture the raw

ADC data using a capture card, such as the TSW1400.

Key features:

• 120-pin connector to interface with the TSW1400 EVM.

• 20-pin LaunchPad connectors for all the digital controls from the Radar EVM.

• 60-pin high-density (HD) connector for the high-speed ADC data over CSI or LVDS interface and

emulator signals from the BoosterPack.

• Onboard FTDI chip to provide PC interface for SPI, GPIO controls, UART loggers.

• Powered over the micro USB connector.

• 60-pin MIPI connector for JTAG trace (for the 16xx device only).

• Header for DMM interface (for the 16xx device only).

• Second CAN connector (for the 16xx device only).

1.2 Kit Contents

• MMWAVE-DEVPACK

• Micro USB cable to connect to PC.

• Samtec cable to connect the 60-pin high-density connectors of the DevPack and BoosterPack (PN

HQCD⁃030⁃02.00⁃SEU⁃TBR⁃1).

60-pin HD

Connector

Jumpers to select digital signal

MUX between FTDI chip and

120-pin connector

20-Pin

LaunchPad

Connector

(J5)

20-Pin

LaunchPad

Connector

(J4)

MicroUSB

Connector for PC

Interface and Power

FTDI

CAN2

Connector

DMM Header

60-Pin MIPI

JTAG Trace

Connector

Hardware

www.ti.com

4SWRU506–May 2017

Submit Documentation Feedback

MMWAVE-DEVPACK

2 Hardware

Figure 1. EVM Front View

www.ti.com

Hardware

SWRU506–May 2017

MMWAVE-DEVPACK

Figure 2. EVM Rear View

1:2

Analog

MUX

1:2

Analog

MUX

1:2

Analog

MUX

1:2

Analog

MUX

SAMTEC 120-PIN CONNECTOR

60-PIN

CONNECTOR

FTDI

FT4232H

SPI

I2C

USB

ITAG

TRACE

MIPI-60 TRACE

DEBUG CONNECTOR

40-PIN

LP/BP

CONNECTOR

14-PIN JTAG

HEADER

DMM TRACE

HEADER

100mil

header

100mil

header

CAN

Header

CAN

transceiver

3.3 V, 1A

LDO

VBUS_5V

LVDS/CSI-2

CAN2_TXT

CAN2_RX

SPI1_CS

GPIO_0

PORT_A

PORT_B

PORT_C

PORT_D

GPIO_1

MSS_LOGGER

BSS_LOGGER

Unused pins of

40-pin LP/BP

SPI1_MISO

SPI1_CLK

SPI1_MOSI

SPI1_HOST_INTR

WARMRST

GPIO_2

NRST

SOR1

SOR2

SOR3

HOST_INTR

FTDI_3V3,

BRD_3V3

Hardware

www.ti.com

6SWRU506–May 2017

Submit Documentation Feedback

MMWAVE-DEVPACK

2.1 Block Diagram

Figure 3. Block Diagram

2.2 Connecting the mmwave Sensor BoosterPack to the DevPack

The two boards connect directly over the 20-pin LaunchPad connectors, and the 60-pin HD connectors

are connected using a separate Samtec cable (HQCD⁃030⁃02.00⁃SEU⁃TBR⁃1). The BoosterPack is

always placed above the DevPack. The connectors do not have a key to prevent the misalignment of the

pins or reverse connection. Thus, ensure that reverse mounting does not occur. While connecting the

BoosterPack to DevPack, ensure the pin 1 orientation is correct by matching the 3V3 and 5-V signal

marking on both the boards. Figure 4 illustrates the connection orientation.

www.ti.com

Hardware

SWRU506–May 2017

MMWAVE-DEVPACK

Figure 4. Example BoosterPack Connection with DevPack

2.3 Power Connections

The DevPack is powered by the micro USB cable. However, the onboard LDO is enabled only when the

BoosterPack connected to the DevPack is powered. This is to prevent the DevPack from powering up

before the BoosterPack. This is done by looking for 3.3 V on the PGOOD_3V3 line available J4 connector,

pin#14.

When the two boards are powered, the VBUS LED (DS6) and 3V3 LED (DS7) glow, as shown in Figure 5.

Figure 5. VBUS LED (DS6) and 3V3 LED (DS7)

Hardware

www.ti.com

8SWRU506–May 2017

Submit Documentation Feedback

MMWAVE-DEVPACK

2.4 Connectors

2.4.1 20-Pin BoosterPack Connectors (J5 , J4)

The 20-pin BoosterPack connectors mate directly with the mmwave BoosterPack. The orientation of the

boards while connected must be ensured by matching the 3V3 and 5-V pin markings on both the boards,

as shown in Figure 6.

Figure 6. 20-Pin BoosterPack Connectors

2.4.2 60-Pin High Density (HD) Connector (P3)

The 60-pin HD connector (see Figure 7) provides the high-speed CSI/LVDS data, controls signals (SPI ,

UART, I2C, NRST, NERR, and SOPs), and JTAG debug signals from the BoosterPack. The Trace and

DMM interface lines are also available through this connector.

Figure 7. 60-Pin HD Connector

www.ti.com

Hardware

SWRU506–May 2017

MMWAVE-DEVPACK

2.4.3 120-Pin High Density (HD) Connector (J6)

This connector enables interfacing the LVDS signals to the TSW1400 EVM or the CSI, and control signals

to the central processor board, as shown in Figure 8.

Figure 8. 120-Pin TSW EVM Interface Connector

2.4.4 MIPI 60-Pin JTAG Connector (J3)

This connector provides the standard MIPI 60-pin interface for JTAG and trace capability (trace is

available only on the 1642 device), through emulators such as the XDS560pro (see Figure 9). To use this

interface, tlhe JTAG lines to the onboard emulator (XDS110) on the mmwave BoosterPack must be

disconnected. This is done by removing the resistors R69, R70, R71, and R30 from the mmwave BOOST

boards.

Figure 9. MIPI 60-Pin JTAG Connector

Hardware

www.ti.com

10 SWRU506–May 2017

Submit Documentation Feedback

MMWAVE-DEVPACK

2.4.5 TI 14-Pin JTAG Connector (P8)

This connector provides a JTAG interface for debug and development, through emulators such as the

XDS100 (see Figure 10). To use this interface, the JTAG lines to the onboard emulator (XDS110) on the

mmwave BoosterPack must be disconnected. This is done by removing the resistors R69, R70, R71, and

R30 on the mmwave BoosterPacks.

Figure 10. TI 14-Pin JTAG Connector

2.5 PC Connection

Connectivity is provided through the micro USB connector over the onboard FTDI IC. This provides the

following interfaces to the PC:

• FTDI Port A -> SPI interface for radar device control using Radar Studio.

• FTDI Port B-> I2C interface and host INTR signal.

• FTDI Port C -> BSS Logger port (for internal debug only), Nrst control, and Nerror signals.

• FTDI Port D -> DSS Logger port (available only on 1642 device), SOP line control signals, and GPIO

signals

When the USB is connected for the first time to the PC, Windows®maybe not be able to recognize the

device. This is indicated in the device manager with yellow exclamation marks, as shown in Figure 11.

Figure 11. Uninstalled Devices

Tabla de contenidos

Otros manuales de Placa madre de Texas Instruments

Texas Instruments

Texas Instruments BQ79600-Q1 Manual de usuario

Texas Instruments

Texas Instruments DAC8554EVM Manual de usuario

Texas Instruments

Texas Instruments LM25085A Manual de usuario

Texas Instruments

Texas Instruments LM3464 Instrucciones de instalación y funcionamiento

Texas Instruments

Texas Instruments TPS65218EVM Manual de usuario

Texas Instruments

Texas Instruments TPA032D01 Manual de usuario

Texas Instruments

Texas Instruments bq50002AEVM-607 Manual de usuario

Texas Instruments

Texas Instruments BQ75614-Q1 Manual de usuario

Texas Instruments

Texas Instruments PGA411-Q1 EVM Manual de usuario

Texas Instruments

Texas Instruments TPS40195 Manual de usuario

Texas Instruments

Texas Instruments UCD3138CC64EVM-030 Manual de usuario

Texas Instruments

Texas Instruments TPS2663-166EVM Manual de usuario

Texas Instruments

Texas Instruments TLV62080 Manual de usuario

Texas Instruments

Texas Instruments ADS9120EVM-PDK Manual de usuario

Texas Instruments

Texas Instruments TAS3308EVM Manual de usuario

Texas Instruments

Texas Instruments eFuse TPS25983EVM Manual de usuario

Texas Instruments

Texas Instruments LP8557EVM Manual de usuario

Texas Instruments

Texas Instruments ADC DJ Series Manual de usuario

Texas Instruments

Texas Instruments BOOSTXL-DRV8320 Series Manual de usuario

Texas Instruments

Texas Instruments TPA2005D1 Manual de usuario

Texas Instruments

Texas Instruments ADS7066EVM-PDK Manual de usuario

Texas Instruments

Texas Instruments DRV10963 Manual de usuario

Texas Instruments

Texas Instruments TLV752-EVM Manual de usuario

Texas Instruments

Texas Instruments MSP430FR6047 Manual de usuario

Manuales populares de Placa madre de otras marcas

DFI

DFI SD170 Manual de usuario

ASROCK

ASROCK ROMED8-2T Manual de usuario

Asus

Asus P2L97A Manual de usuario

Winmate

Winmate IC70 Manual de usuario

Asus

Asus MES-B Manual de usuario

Grantech

Grantech SYS8F377VGGA-3OMN Manual de usuario

Telit Wireless Solutions

Telit Wireless Solutions SL869-3DR Manual de usuario

Gigabyte

Gigabyte GA-9IVDT Manual de usuario

Commell

Commell MS-C73 Manual de usuario

IBT Technologies

IBT Technologies MB860 Manual de usuario

Nvidia

Nvidia TEGRA DG-04927-001_V01 Manual de usuario

Biostar

Biostar M7VIT Bravo Instrucciones de funcionamiento e instalación

Intel

Intel D33217CK Manual de usuario

Asus

Asus F1A55-M LX PLUS R2.0 Manual de usuario

EPC

EPC EPC9147C Manual de usuario

Asus

Asus EX-B760M-V5 D4 Manual de usuario

EPOX

EPOX MU-8KHA0010 Manual de usuario

Ski-Doo

Ski-Doo Bombardier MPEM 219 700 090 Manual de usuario