Texas Instruments LMX2595 EVM Manual de usuario

SNAU219B–June 2017–Revised March 2020

LMX2595 EVM Instructions – 20-GHz Wideband Low Noise PLL With

Integrated VCO

User's Guide

SNAU219B–June 2017–Revised March 2020

LMX2595 EVM Instructions – 20-GHz Wideband Low Noise

PLL With Integrated VCO

This Evaluation Module is for the LMX2595, which is the first PLL with integrated VCO in industry to get

fundamental VCO output up to 20 GHz. The industry leading PLL FOM is –236 dBc/Hz with 1/f of –129

dBc/Hz. This device supports the JESD204B standard (as in the LMX2595 can generate or repeat the

SYSREF signal), and is designed for clock high-speed data converters. The integrated jitter from the EVM

measurements is less than 50 fs at 9-GHz carrier frequency. By providing a SYNC signal, the user can

synchronize the output phase across multiple LMX2595 devices. The LMX2595 can also generate a

frequency ramp as demonstrated in this evaluation module. With an on-board oscillator, the setup process

only requires a 3.3-V power supply and an included Reference Pro module (For SPI Programming

interface). The software is simple with an intuitive and user-friendly GUI.

Figure 1. LMX2595EVM

Contents

1 Evaluation Board Setup .................................................................................................... 3

2 EVM Description ............................................................................................................. 3

2.1 Installing the Software.............................................................................................. 4

3 Bringing LMX2595 to a Lock State........................................................................................ 5

4 Loop Filter Configuration.................................................................................................... 5

www.ti.com

2SNAU219B–June 2017–Revised March 2020

Submit Documentation Feedback

LMX2595 EVM Instructions – 20-GHz Wideband Low Noise PLL With

Integrated VCO

5 Key Results to Expect....................................................................................................... 6

Appendix A Schematic............................................................................................................ 7

Appendix B Bill of Materials...................................................................................................... 8

Appendix C Board Layers Stack-Up ............................................................................................ 9

Appendix D Changing Reference Oscillator and Setup..................................................................... 11

Appendix E Connecting Reference Pro....................................................................................... 12

Appendix F Ramping Feature ................................................................................................. 14

Appendix G SYSREF Feature ................................................................................................. 15

Appendix H Enabling Onboard DC-DC Buck Converter (TPS62150)..................................................... 16

Appendix I Appendix J: Using the VCO Doubler ........................................................................... 17

Trademarks

PLLATINUM is a trademark of Texas Instruments.

All other trademarks are the property of their respective owners.

Diff. RF

Output A

Diff. RF

Output B

LMX2595

Reference input

SE or Diff

Power supply

3.3 Volt

SYNC

SYSREF

Lock

indicator

LED

1: SPI read block

2: Lock indicator

Upper position = ON

Lower position = OFF

Loop filter

components

(*_LF)

Serial Interface Pin-out

2 4 6 8 10

13579

(Optional)

Add a XO here

3.3 V supply

RFoutAP

Connect to

an analyzer

50 

termination

Connect to

a PC

Clean 100 MHz

clock source

Reference Pro

board LMX2595EVM

board

Connect both

serial interface

together

OSCinM can be left

open

www.ti.com

Evaluation Board Setup

SNAU219B–June 2017–Revised March 2020

LMX2595 EVM Instructions – 20-GHz Wideband Low Noise PLL With

Integrated VCO

1 Evaluation Board Setup

Figure 2. LMX2595EVM Setup

1. Power:

a. Set power supply to 3.3 V with 600-mA current limit and connect to VCC SMA.

2. Input Signal:

a. Connect a clean 100-MHz clock source to the OSCinP SMA.

3. Programming Interface:

• Reference Pro will provide SPI interface to program LMX2595.

a. Connect USB cable from laptop or PC to USB port in Reference Pro. This provides power to

Reference Pro Board and communication with TICS GUI.

b. Connect 10-pin ribbon cable from Reference Pro to LMX2595EVM as shown above.

4. Output:

a. Connect RFoutAM or RFoutAP to a phase noise analyzer. Connect a 50-Ωresistor on the unused

pin if you are using a single-ended output. Use a balun if you are using a differential output.

2 EVM Description

The LMX2595 is populated on a 4-layer PCB. This brief description should help you use the EVM:

Figure 3. LMX2595EVM Description

EVM Description

www.ti.com

4SNAU219B–June 2017–Revised March 2020

Submit Documentation Feedback

LMX2595 EVM Instructions – 20-GHz Wideband Low Noise PLL With

Integrated VCO

The serial interface pin description is as follow:

Table 1. Serial Interface Connector Description

NO. NAME

1RAMPDIR and CE (Choose with

Resistors on Board)

2 CSB

3 MUXout

4 SDI

5 Not Used

6 GND

7 RampCLK

8 SCK

9 SysRefReq

10 SYNC

2.1 Installing the Software

1. Download TICS Pro from the TI Website at www.ti.com/tool/TICSPRO-SW.

2. Install the software by following the wizard.

3. Search for the LMX2595. In the menu bar, search Select Device →PLL + VCO →LMX2595.

Figure 4. Search for LMX2595 on TICS Pro

4. You are now ready to use this software. Verify that you can communicate with Reference Pro. Select

Interface under USB communications.

Figure 5. USB Communications on TICS Pro

5. Click on Identify and you will see the LED (MSP430 Supplied) blinks on Reference Pro.

www.ti.com

Bringing LMX2595 to a Lock State

SNAU219B–June 2017–Revised March 2020

LMX2595 EVM Instructions – 20-GHz Wideband Low Noise PLL With

Integrated VCO

Figure 6. USB Communication Between TICS Pro and Reference Pro

3 Bringing LMX2595 to a Lock State

1. Load the default mode by clicking on Default configuration →Default Mode xxxx-xx-xx.

2. From the menu bar, select USB communications →Write All Registers to write all the registers to

LMX2595.

Figure 7. TICS Pro GUI LMX2595 Default Configuration

4 Loop Filter Configuration

The parameters for the loop filters are:

Table 2. Current Loop Filter Configuration

PARAMETER VALUE

VCO Gain 132 MHz/V

Loop Bandwidth 285 kHz

Phase Margin 65 deg

C1_LF 390 pF

C2_LF 68 nF

C3_LF Open

C4_LF 1800 pF

Key Results to Expect

www.ti.com

6SNAU219B–June 2017–Revised March 2020

Submit Documentation Feedback

LMX2595 EVM Instructions – 20-GHz Wideband Low Noise PLL With

Integrated VCO

Table 2. Current Loop Filter Configuration (continued)

PARAMETER VALUE

R2 68 Ω

R3_LF 0 Ω

R4_LF 18 Ω

Effective Charge Pump Gain 15 mA

Phase Detector Frequency (MHz) 200 MHz

VCO Frequency Designed for 15 GHz, but works

over the whole frequency range

Figure 8. Loop Filter Configuration

For detailed design and simulation of TI's PLLATINUM™ integrated circuits, see the PLLatinum Sim Tool.

For application notes, blogs, or videos on TI PLL products, see http://www.ti.com/pll.

5 Key Results to Expect

Figure 9. Phase Noise Plot at 14-GHz Output Frequency

This assumes that the input reference is very clean, such as a 100-MHz Wenzel oscillator. A signal

generator is NOT sufficiently clean.

SNAU219B–June 2017–Revised March 2020

Schematic

Appendix A

SNAU219B–June 2017–Revised March 2020

Schematic

Figure 10. Schematic

8SNAU219B–June 2017–Revised March 2020

Submit Documentation Feedback

Bill of Materials

Appendix B

SNAU219B–June 2017–Revised March 2020

Bill of Materials

Table 3. Bill of Materials

DESIGNATOR DESCRIPTION MANUFACTURER PART NUMBER QUANTITY

C1, C3, C9, C14, C15, C17, C30 CAP, CERM, 0.1 µF, 16 V, ±5%, X7R,

0603 AVX 0603YC104JAT2A 7

C1_LF CAP, CERM, 390 pF, 50 V, ±5%,

C0G/NP0, 0603 Kemet C0603C391J5GACTU 1

C2, C4, C8, C16 CAP, CERM, 10 µF, 10 V, ±10%, X5R,

0805 Kemet C0805C106K8PACTU 4

C2_LF CAP, CERM, 0.068 µF, 50 V, ±10%, X7R,

0603 MuRata GRM188R71H683KA93D 1

C4_LF CAP, CERM, 1800 pF, 50 V, ±5%,

C0G/NP0, 0603 MuRata GRM1885C1H182JA01D 1

C5, C6, C7, C10, C11, C12 CAP, CERM, 0.01 µF, 16 V, ±10%, X7R,

0402 AT Ceramics 520L103KT16T 6

C18, C23, C24, C26, C27, C28, C29 CAP, CERM, 1 µF, 16 V, ±10%, X7R, 0603 TDK C1608X7R1C105K080AC 7

C19, C20, C21, C22, C25 CAP, CERM, 10 µF, 10 V, ±20%, X5R,

0603 TDK C1608X5R1A106M080AC 5

CE_TP, CSB_TP, GND_TP, MUXout_TP,

RampCLK_TP, RampDIR_TP, SCK_TP,

SDI_TP, SYNC_TP, SysRefReq_TP,

Vcc_TP, VccRF_TP, Vtune_TP

Test Point, Compact, White, TH Keystone 5007 13

Cin_0 CAP, CERM, 10 µF, 25 V, ±10%, X5R,

0805 MuRata GRM219R61E106KA12D 1

Cout0 CAP, CERM, 22 µF, 16 V, ±10%, X5R,

0805 TDK C2012X5R1C226K125AC 1

Css CAP, CERM, 3300 pF, 50 V, ±5%,

C0G/NP0, 0603 MuRata GRM1885C1H332JA01D 1

D1 LED, Green, SMD Lite-On LTST-C190GKT 1

L1, L2 Inductor, Multilayer, Air Core, 18 nH, 0.3 A,

0.36 Ω, SMD MuRata LQG15HS18NJ02D 2

L1_TPS Inductor, Shielded, Composite, 2.2 µH, 3.7

A, 0.02 Ω, SMD Coilcraft XFL4020-222MEB 1

MUXout_SW Switch, SPST, Slide, Off-On, 2 Pos, 0.1 A,

20 V, SMD CTS Electrocomponents 219-2MST 1

OSCinM, OSCinP, SYNC, SysRef, Vcc Connector, SMT, End launch SMA 50 ohm Emerson Network Power

Connectivity 142-0701-851 5

R1 RES, 330 Ω, 5%, 0.1 W, 0603 Yageo America RC0603JR-07330RL 1

R2 RES, 100 k, 5%, 0.1 W, 0603 Vishay-Dale CRCW0603100KJNEA 1

R2_LF RES, 68, 5%, 0.1 W, 0603 Vishay-Dale CRCW060368R0JNEA 1

R3_LF, R12, R15, R24, R25, R26, R30,

R31, R34, R35, R36, R41, R42, R43, R44,

R45 RES, 0, 5%, 0.1 W, 0603 Vishay-Dale CRCW06030000Z0EA 16

R4_LF RES, 18, 5%, 0.1 W, 0603 Vishay-Dale CRCW060318R0JNEA 1

R5, R7, R8, R9, R16, R19, R20, R22 RES, 12 kΩ, 5%, 0.1 W, 0603 Vishay-Dale CRCW060312K0JNEA 8

R37, R38, R39, R40 RES, 50, 0.1%, 0.05 W, 0402 Vishay-Dale FC0402E50R0BST1 4

Rfbb1 RES, 180 k, 0.1%, 0.1 W, 0603 Yageo America RT0603BRD07180KL 1

Rfbt1 RES, 562 k, 1%, 0.1 W, 0603 Vishay-Dale CRCW0603562KFKEA 1

RFoutAM, RFoutAP, RFoutBM, RFoutBP JACK, SMA, 50 Ω, Gold, Edge Mount Johnson 142-0771-831 4

U1 High Performance, Wideband PLLatinum™

RF Synthesizer Texas Instruments LMX2595RHAR 1

uWire Header (shrouded), 100 mil, 5x2, Gold

plated, SMD FCI 52601-S10-8LF 1

Top layer

RO4003 (Er = 3.38)

16 mil

GND layer

FR4 (Er = 4.6)

Power layer

FR4 (Er = 4.6)

Bottom layer

62 mil

SNAU219B–June 2017–Revised March 2020

Board Layers Stack-Up

Appendix C

SNAU219B–June 2017–Revised March 2020

Board Layers Stack-Up

The top layer is 1-oz. copper.

Figure 11. Board Layer Stack-Up

Figure 12. Top Layer

Appendix C

www.ti.com

10 SNAU219B–June 2017–Revised March 2020

Submit Documentation Feedback

Board Layers Stack-Up

Figure 13. GND Layer

Figure 14. Power Layer

Figure 15. Bottom Layer

Tabla de contenidos

Otros manuales de Placa madre de Texas Instruments

Texas Instruments

Texas Instruments LM2695EVAL Manual de usuario

Texas Instruments

Texas Instruments TPS8802EVM Manual de usuario

Texas Instruments

Texas Instruments LMK5B33414EVM Manual de usuario

Texas Instruments

Texas Instruments PCI2250 Manual de usuario

Texas Instruments

Texas Instruments DLP5534PROJQ1EVM Manual de usuario

Texas Instruments

Texas Instruments TPS65010EVM-230 Manual de usuario

Texas Instruments

Texas Instruments OMAP35 Series Manual de usuario

Texas Instruments

Texas Instruments ADS7066EVM-PDK Manual de usuario

Texas Instruments

Texas Instruments TPS23882B1EVM Manual de usuario

Texas Instruments

Texas Instruments DAC3XJ8XEVM Manual de usuario

Texas Instruments

Texas Instruments BQ75614-Q1 Manual de usuario

Texas Instruments

Texas Instruments LMH1297 Manual de usuario

Texas Instruments

Texas Instruments DS90UB95x-Q1EVM Series Manual de usuario

Texas Instruments

Texas Instruments TMAG5115 Manual de usuario

Texas Instruments

Texas Instruments ADS5292 Manual de usuario

Texas Instruments

Texas Instruments TPS61040EVM Manual de usuario

Texas Instruments

Texas Instruments PCA9306 Manual de usuario

Texas Instruments

Texas Instruments TPS54380EVM-001 Manual de usuario

Texas Instruments

Texas Instruments ADC 120EVM-PDK Series Manual de usuario

Texas Instruments

Texas Instruments DRV8873 EVM Series Manual de usuario

Texas Instruments

Texas Instruments ADS1 20EVM Series Manual de usuario

Texas Instruments

Texas Instruments INA4180-INA4181 Manual de usuario

Texas Instruments

Texas Instruments DS125DF1610 Manual de usuario

Texas Instruments

Texas Instruments BQ25883 Manual de usuario

Manuales populares de Placa madre de otras marcas

DFI

DFI SD170 Manual de usuario

ASROCK

ASROCK ROMED8-2T Manual de usuario

Asus

Asus P2L97A Manual de usuario

Winmate

Winmate IC70 Manual de usuario

Asus

Asus MES-B Manual de usuario

Grantech

Grantech SYS8F377VGGA-3OMN Manual de usuario

Telit Wireless Solutions

Telit Wireless Solutions SL869-3DR Manual de usuario

Gigabyte

Gigabyte GA-9IVDT Manual de usuario

Commell

Commell MS-C73 Manual de usuario

IBT Technologies

IBT Technologies MB860 Manual de usuario

Nvidia

Nvidia TEGRA DG-04927-001_V01 Manual de usuario

Biostar

Biostar M7VIT Bravo Instrucciones de funcionamiento e instalación

Intel

Intel D33217CK Manual de usuario

Asus

Asus F1A55-M LX PLUS R2.0 Manual de usuario

EPC

EPC EPC9147C Manual de usuario

Asus

Asus EX-B760M-V5 D4 Manual de usuario

EPOX

EPOX MU-8KHA0010 Manual de usuario

Ski-Doo

Ski-Doo Bombardier MPEM 219 700 090 Manual de usuario