Texas Instruments DLP3010 Manual de usuario

DLPU070B–July 2018–Revised February 2019

DLP3010 Light Control EVM User’s Guide

User's Guide

DLPU070B–July 2018–Revised February 2019

DLP3010 Light Control EVM User’s Guide

This user’s guide presents an overview of the DLP3010 Light Control evaluation module (EVM) and a

general description of the main features and functions. It explains the first steps to get started, and shows

a detailed description of the push buttons function, the on board LEDs, and the main connectors.

Contents

1 DLP3010 Light Control EVM Overview ................................................................................... 2

2 Safety Instructions .......................................................................................................... 3

3 Applicable Documents ...................................................................................................... 3

4 What is in the DLP3010 Light Control EVM? ............................................................................ 4

5 Light Engine .................................................................................................................. 5

6 Quick-Start Procedure....................................................................................................... 5

7 Circuit Description ........................................................................................................... 7

8 EVM Setup.................................................................................................................... 9

List of Figures

1 DLP3010 Light Control Complete EVM................................................................................... 2

2 DLP3010 Light Control EVM Block Diagram ............................................................................ 4

3 DLP3010 Light Control EVM Optical Engine............................................................................. 5

4 Optical Engine with Focus Adjustment.................................................................................... 6

5 DLP3010 Light Control Main Board ....................................................................................... 9

6 DLP3010 Light Control Connections .................................................................................... 10

7 LED Connection............................................................................................................ 10

8 DLP3010 Light Control Complete EVM ................................................................................. 11

List of Tables

1 Optical Engine Specifications .............................................................................................. 5

2 LEDs on the DLP3010 Light Control EVM ............................................................................... 6

3 Installed Connectors on Main Board...................................................................................... 7

4 Installed Push Buttons and Switch on Main Board ..................................................................... 7

5 Installed Connectors on the DLP3010 Light Control Display Board .................................................. 7

6 DLP3010 Light Control Trigger Description ............................................................................. 8

DLP3010 Light Control EVM Overview

www.ti.com

2DLPU070B–July 2018–Revised February 2019

Submit Documentation Feedback

DLP3010 Light Control EVM User’s Guide

1 DLP3010 Light Control EVM Overview

This DLP3010 Light Control EVM includes an example light engine design composing of DLP electronics

and optics along with GUI software to provide a flexible light steering solution with high brightness and

resolution for industrial, medical and scientific applications. This EVM features DLP3010, DLPC3478 and

DLPA2005 DLP components and offers a compelling combination of resolution, brightness, and

programmability in a small form factor.

Figure 1. DLP3010 Light Control Complete EVM

In addition to this document, use documents listed in Section 3.

www.ti.com

Safety Instructions

DLPU070B–July 2018–Revised February 2019

DLP3010 Light Control EVM User’s Guide

2 Safety Instructions

CAUTION

Caution hot surface. Contact may cause burns. Do not touch.

WARNING

Possible hazardous optical radiation emitted from this EVM. Do not

stare at the operating lamp. There are no user serviceable parts

inside the EVM optical engine. Never open the optical engine,

which can expose a risk group 2 LED which may be harmful to the

eye.

WARNING

Observe handling precautions. Electrostatic sensitive devices.

WARNING

Always ensure both fans are running during operation to avoid

overheating and ensure reliable operation.

3 Applicable Documents

The following documents are applicable to the DLP3010 Light Control EVM and are available at TI.com

(www.ti.com).

• DLP3010 (0.3 720p) DMD data sheet (DLPS051)

• DLPC3478 Display and Light Controller data sheet (DLPS111)

• DLP Display and Light Control EVM GUI Tool User's Guide (DLPU074)

If you need assistance, refer to the DLP and MEMS TI E2E community support forums.

What is in the DLP3010 Light Control EVM?

www.ti.com

4DLPU070B–July 2018–Revised February 2019

Submit Documentation Feedback

DLP3010 Light Control EVM User’s Guide

4 What is in the DLP3010 Light Control EVM?

The DLP3010 Light Control module consists of three subsystems:

• Light engine – includes the optics, red, green, and blue LEDs, and a 1280 × 720 (720p) DMD

• Driver board – includes the DLP chipset comprising of the DLPC3478 controller and DLPA2005

PMIC/LED driver. Includes a header to access Trigger IN/OUT signals for camera capture and other

system controls

• System board – includes the MSP430, the ITE HDMI receiver, the USB-Serial Bridge controller, and

several connectors for external inputs (HDMI, USB, etc.)

Figure 2. DLP3010 Light Control EVM Block Diagram

80.35

56.97

21.00

20.50

www.ti.com

Light Engine

DLPU070B–July 2018–Revised February 2019

DLP3010 Light Control EVM User’s Guide

5 Light Engine

The optical engine, Model H6 is developed and manufactured by Shenzenby Anhua Optoelectronics

Technology Co., Ltd. and is production ready.

The light engine consists of the following components:

• 0.3-inch 720p DMD (DLP3010)

• OSRAM red, green, and blue LED

This light engine interfaces with the EVM using DMD pin mapping Option 1. Refer to the DLPC3478

datasheet for more information about the DMD interface.

Table 1. Optical Engine Specifications

PARAMETER MIN TYP MAX UNIT

Brightness 125 Lum

LED Current 2.4 A

Brightness Uniformity 75%

Throw Ratio 1.2

Offset 100%

Optics F-number F/1.7

Figure 3. DLP3010 Light Control EVM Optical Engine

6 Quick-Start Procedure

This quick-start assumes default conditions as shipped.

1. Power up the DLP3010 Light Control EVM by applying an external DC power supply (19-V DC, 3.42 A)

to the J10 connector. The P5V_VIN (D5) and P3P3V_SB (D6) LED will turn on to indicate that 5-V and

3.3-V standby power is applied.

External Power Supply Requirements:

• Nominal output voltage: 19-V DC

• Minimum output current: 3A; Max output current: 3.42 A

• Efficiency level: VI

NOTE: TI recommends using an external power supply that complies with applicable regional safety

standards such as UL, CSA, VDE, CCC, PSE, etc. A DC Power Connector 2.5mm x 5.5mm is being

used on the DLP3010 Light Control EVM Main Board.

Focus

Adjustment

Quick-Start Procedure

www.ti.com

6DLPU070B–July 2018–Revised February 2019

Submit Documentation Feedback

DLP3010 Light Control EVM User’s Guide

NOTE: The system is designed to operate also with an external 12-V DC power supply.

2. Move the SW_ONOFF switch to the ON position to turn the DLP3010 Light Control EVM on. When the

DLP3010 Light Control EVM is turned on, the PROJ_ON LED D3 will turn on.

3. After the DLP3010 Light Control EVM is turned on; the projector will default to displaying a DLP Light

Control splash image.

4. The focus of the image can be adjusted on the optical engine.

Figure 4. Optical Engine with Focus Adjustment

5. Connect USB to the DLP3010 Light Control EVM and open the DLP3010 Display and Light Control

Graphical User Interface (GUI) on your computer. If needed, connect an HDMI source to the EVM and

communicate to the EVM over the GUI software.

6. Via the GUI the EVM can be set to Video Display Mode or Light Control Modes. Refer to the GUI

user's guide for further description. Note: Install Jumper J11 on the DLP3010 Light Control EVM Main

Board to set Trigger IN/OUT voltage on the EVM. This jumper is required to gain access to the trigger

signals. The jumper is not included by default.

7. When turning off the projector, turn off the SW_ONOFF switch prior to removing power cable.

Note: To avoid potential damage to the DMD, it is recommended to turn off the projector with

SW_ONOFF before disconnecting the power.

There are ten indicator LEDs on the DLP3010 Light Control EVM, and they are defined in Table 2:

Table 2. LEDs on the DLP3010 Light Control EVM

LED REFERENCE SIGNAL INDICATION DESCRIPTION

D1 HOST_IRQ ON during DLPC3478 boot OFF when projector is running.

Indication of DLPC3478 boot-up completed and ready to receive

commands

D2 RESETZ OFF when projector is turned on vie SW_ONOFF

D3 PROJ_ON On when projector is turned on via SW_ONOFF

D5 P5V_VIN 5-V power applied

D6 P3P3V_SB Regulated 3V3 power on

D7 MSP2 ON when HDMI cable plugged in and external video detected.

OFF when external video is not detected.

D8 ACK ON when Cypress CY3420 is I2C master OFF when MSP430 is

I2C master

D9 REQ ON when Cypress CY3420 requests the MSP430 to give

Cypress master control of the I2C bus

D10 GPIO1 Blinking when PC is communicating to flash over SPI

D11 GPIO0 Blinking when PC is communicating to DLPC3478 over I2C

www.ti.com

Circuit Description

DLPU070B–July 2018–Revised February 2019

DLP3010 Light Control EVM User’s Guide

7 Circuit Description

7.1 Connectors, Switch, and Push Buttons on Main Board

Table 3. Installed Connectors on Main Board

INSTALLED CONNECTORS/HEADERS DESCRIPTION

J1 MSP430 JTAG programming interface connector

J2 Header for 5-V DC power (not installed by default)

J3 Connector for audio

J4 Unsupported

J5 Header for EDID programming

J6 Connector for HDMI input

J7 Header for 5-V DC power used for fan connection

J8 Unsupported

J9 60-pin connector for DLP Light Control Display board

J10 Connector for 19-V external power supply interface

J11 Header for voltage level selection for Trigger-in/out (Install jumper to receive

output signal this is not included with the EVM )

J12 Header for remaining DLPC3478 test points (not installed by default)

J13 Connector for Mini-USB cable

J14 Connector for the I2C interface (DevaSys box) (not installed by default)

Table 4. Installed Push Buttons and Switch on Main Board

INSTALLED SWITCHES/PUSH BUTTONS DESCRIPTION

SW1 Projector ON/OFF switch

PB-UP1

Source selection

• First press: TPG

• Second press: HDMI input

• Third press: Splash screen

PB-SEL1 Cycle through displaying 7 curtain colors

PB-DOWN1 Flip image N/S or E/W

PB_LEFT1 Cycle 9 different TPG patterns after TPG source selected

Cycle 4 different splash screens after splash source selected

Change of volume when HDMI input is selected

PB_RIGHT1 Change LED current total 7 steps

Change of volume when HDMI input is selected

7.2 Connectors on DLP3010 Light Control Display Board

Table 5. Installed Connectors on the DLP3010 Light Control Display Board

INSTALLED CONNECTORS/HEADERS DESCRIPTION

J1 Connector for the DMD flex cable

J2 Connector for LED cable

J3 Connector for selecting 3DR signal usage (Display or Light Control)

J4 Connector for Trigger-in and Triger-out for Light Control Application

J5 60-pin connector for DLP Light Control Display board

Circuit Description

www.ti.com

8DLPU070B–July 2018–Revised February 2019

Submit Documentation Feedback

DLP3010 Light Control EVM User’s Guide

7.3 DLP3010 Light Control Trigger Description

(1) Install Jumper J11 to set Trigger IN/OUT voltage on the EVM (Jumper is not included by default). For 3.3-V signal level: Connect

pin 2 and p 3 of J11. For 1.8-V signal level : Connect pin 1 and pin 2 of J11.

(2) See IMPORTANT note below.

Table 6. DLP3010 Light Control Trigger Description (1)

DLPC3478

PIN J4 PIN CONNECTOR I/O FUNCTION

NO. DESC

3DR 5 3DR_BF Input

For light control applications: Reserved for external trigger signal (Input).

Applicable to Internal Pattern Streaming Mode only.

The 3DR pin on the DLPC3478 can be used as a 3D left or right

reference indicator or as trigger input signal for light control application. A

jumper on J3 has to be installed to determine the use case for this pin.

For display application: Connect pin 1 and pin 2 of J3.

For light control application: Connect pin 2 and pin 3 of J3.

TSTPT_4(2) 7 TSTPT_4_BF Output TRIG_OUT_1 signal.

GPIO_06 3 GPIO_6_BF Output Pattern Ready signal. Applicable to Internal Pattern Streaming Mode only.

GPIO_07 4 GPIO_7_BF Output TRIG_OUT_2_signal.

IMPORTANT: .

The Rev A Display Boards use a level shifter which changes the incoming signal level to

1.8 V. The correct voltage level for the DLP controller is 3.3 V. If EVM does not detect the

input signal correctly, modify the placement of resistors R32 and R35.

• Rotate R35 to disconnect pull-up resistor from the 1.8-V supply.

• Connect free end of R35 to 3.3 V. The 3.3-V connection at R32 can be used.

www.ti.com

EVM Setup

DLPU070B–July 2018–Revised February 2019

DLP3010 Light Control EVM User’s Guide

8 EVM Setup

The DLP3010 Light Control EVM is composed of three parts:

• DLP3010 Light Control main board

• DLP3010 Light Control display board

• Engine with LED connection and flex cable

The main board contains the connector for the power supply, a USB connector to communicate to the

DLP3010 Light Control GUI, HDMI, audio, and the connector for the DLP3010 Light Control display board.

The main board also contains a switch to turn on the projector in case the DLP3010 Light Control display

board and the engine are connected. Figure 5 shows the main connectors on the main board.

Figure 5. DLP3010 Light Control Main Board

The DLP3010 Light Control Display board has three main connectors: The LED connector, the flex cable

connector, and the main board connector. The main and display board connect together via J5 and J9.

Note that the main board connector J5 on the DLP3010 Light Control Display board is on the bottom,

while the LED and flex cable connectors are on the top as shown in Figure 6.

EVM Setup

www.ti.com

10 DLPU070B–July 2018–Revised February 2019

Submit Documentation Feedback

DLP3010 Light Control EVM User’s Guide

Figure 6. DLP3010 Light Control Connections

The LED adapter board connects the three LEDs with the LED connector on the DLP3010 Light Control

Display board. The different connectors for each LED are named on the board as well as on the light

engine. Refer to Figure 7 to see the proper setup. The LEDs are connected accordingly to the LED

datasheet specification.

Ensure a good connection of the flex cable to the DLP Light Control Display board before turning it on.

Figure 7. LED Connection

Figure 8 shows the final setup of all parts.

Este manual sirve para los siguientes modelos

Tabla de contenidos

Otros manuales de Placa madre de Texas Instruments

Texas Instruments

Texas Instruments DAC7811EVM Manual de usuario

Texas Instruments

Texas Instruments TPS92691 Manual de usuario

Texas Instruments

Texas Instruments BP-DAC81404EVM Manual de usuario

Texas Instruments

Texas Instruments DRV8317HEVM Manual de usuario

Texas Instruments

Texas Instruments TPS7B4255EVM-062 Manual de usuario

Texas Instruments

Texas Instruments TLV3602EVM Manual de usuario

Texas Instruments

Texas Instruments bq2415x Manual de usuario

Texas Instruments

Texas Instruments TPS62110EVM-101 Manual de usuario

Texas Instruments

Texas Instruments DLP5534PROJQ1EVM Manual de usuario

Texas Instruments

Texas Instruments TPS62830xRZEREVM Manual de usuario

Texas Instruments

Texas Instruments DAC53608 Manual de usuario

Texas Instruments

Texas Instruments TPS54291 Manual de usuario

Texas Instruments

Texas Instruments LM5157EVM-BST Manual de usuario

Texas Instruments

Texas Instruments TPD2S701-Q1 Manual de usuario

Texas Instruments

Texas Instruments BP-DAC11001EVM Manual de usuario

Texas Instruments

Texas Instruments ADS794x EVM Series Manual de usuario

Texas Instruments

Texas Instruments DAC161S997 Manual de usuario

Texas Instruments

Texas Instruments TMS320C6670 Manual de usuario

Texas Instruments

Texas Instruments DAC53401EVM Manual de usuario

Texas Instruments

Texas Instruments PanelBus TFP201EVM Manual de usuario

Texas Instruments

Texas Instruments TMS320DM6467 DVEVM Manual de usuario

Texas Instruments

Texas Instruments DAC3482 Manual de usuario

Texas Instruments

Texas Instruments DS90UB954-Q1EVM Manual de usuario

Texas Instruments

Texas Instruments OMAP35 Series Manual de usuario

Manuales populares de Placa madre de otras marcas

DFI

DFI SD170 Manual de usuario

ASROCK

ASROCK ROMED8-2T Manual de usuario

Asus

Asus P2L97A Manual de usuario

Winmate

Winmate IC70 Manual de usuario

Asus

Asus MES-B Manual de usuario

Grantech

Grantech SYS8F377VGGA-3OMN Manual de usuario

Telit Wireless Solutions

Telit Wireless Solutions SL869-3DR Manual de usuario

Gigabyte

Gigabyte GA-9IVDT Manual de usuario

Commell

Commell MS-C73 Manual de usuario

IBT Technologies

IBT Technologies MB860 Manual de usuario

Nvidia

Nvidia TEGRA DG-04927-001_V01 Manual de usuario

Biostar

Biostar M7VIT Bravo Instrucciones de funcionamiento e instalación

Intel

Intel D33217CK Manual de usuario

Asus

Asus F1A55-M LX PLUS R2.0 Manual de usuario

EPC

EPC EPC9147C Manual de usuario

Asus

Asus EX-B760M-V5 D4 Manual de usuario

EPOX

EPOX MU-8KHA0010 Manual de usuario

Ski-Doo

Ski-Doo Bombardier MPEM 219 700 090 Manual de usuario