Texas Instruments CC3200MODLAUNCHXL Manual de usuario

CC3200MOD SimpleLink™ Microcontroller and

Wi-Fi® Network Processor Module - LaunchPad

Hardware

User's Guide

Literature Number: SWRU397

December 2014

Contents

1 Introduction......................................................................................................................... 4

1.1 CC3200MOD LaunchPad............................................................................................... 4

1.2 Key Features.............................................................................................................. 4

1.3 What's Included .......................................................................................................... 5

1.4 FCC/IC Regulatory Compliance........................................................................................ 5

2 Hardware Description........................................................................................................... 6

2.1 Block Diagram............................................................................................................ 7

2.2 Hardware Features....................................................................................................... 7

2.3 Connecting a BoosterPack.............................................................................................. 8

2.4 Jumpers, Switches and LEDs .......................................................................................... 8

2.5 Power..................................................................................................................... 14

2.6 Measure CC3200MOD Current Drawn .............................................................................. 16

2.7 RF Connections......................................................................................................... 18

2.8 Design Files ............................................................................................................. 19

3 Software Examples............................................................................................................. 20

3.1 Development Environment Requirements........................................................................... 20

4 Additional Resources.......................................................................................................... 21

4.1 LaunchPad Wiki......................................................................................................... 21

4.2 Information on the CC3200MOD ..................................................................................... 21

4.3 Download CCS, IAR.................................................................................................... 21

4.4 CC3200 Code Examples .............................................................................................. 21

4.5 CC3200 Application Notes ............................................................................................ 21

4.6 The TI E2E Community................................................................................................ 21

2Table of Contents SWRU397–December 2014

Submit Documentation Feedback

www.ti.com

List of Figures

1 CC3200MOD LaunchPad EVM Overview................................................................................ 6

2 CC3200MOD LaunchPad Block Diagram ................................................................................ 7

3 Pn-1 Marking on the CC3200MOD LaunchPad (White Triangle) ..................................................... 8

4 JTAG Headers ............................................................................................................... 8

5 I2C Connections ............................................................................................................. 9

6 UART Signals............................................................................................................... 10

7 SOP Jumpers .............................................................................................................. 10

8 2x20 Pin Connector........................................................................................................ 14

9 Powering From USB....................................................................................................... 15

10 Battery Power............................................................................................................... 15

11 Measuring Low Power..................................................................................................... 16

12 Measuring Active Power................................................................................................... 17

13 Radiated Testing Using Chip Antenna .................................................................................. 18

14 Board Set for Conducted Testing ........................................................................................ 18

List of Tables

1 JTAG Headers ............................................................................................................... 8

2 Jumper Settings.............................................................................................................. 9

3 Default I2C Addresses ...................................................................................................... 9

4 Jumper Settings.............................................................................................................. 9

5 UART Signals............................................................................................................... 10

6 SOP Lines................................................................................................................... 10

7 Miscellaneous Settings .................................................................................................... 11

8 Push Buttons................................................................................................................ 12

9 LEDs ......................................................................................................................... 13

10 Change Log................................................................................................................. 19

SWRU397–December 2014 List of Figures

User's Guide

SWRU397–December 2014

CC3200MOD SimpleLink™ Microcontroller and Wi-Fi®

Network Processor Module - LaunchPad Hardware

1 Introduction

1.1 CC3200MOD LaunchPad

Start your design with the CC3200 module LaunchPad (CC3200MODLAUNCHXL), which encapsulates

the industry’s first programmable wireless microcontroller (MCU) module with built-in Wi-Fi connectivity.

Created for the Internet of Things (IoT), the SimpleLink CC3200MOD is a wireless MCU module that

integrates an ARM Cortex-M4 MCU, allowing customers to develop an entire application using a single

device. The CC3200MOD integrates all required system-level hardware components including clocks, SPI

flash, RF switch, and all required passive components.

This document explains the various configurations of the CC3200MODLAUNCHXL, a low-cost evaluation

platform which hosts the CC3200MOD. The module LaunchPad also features programmable user buttons,

RGB LED for custom applications, temperature and accelerometer sensors, as well as onboard emulation

for debugging. The LaunchPad stackable headers interface demonstrates how to expand the functionality

of the CC3200MOD when interfacing with other peripherals on existing BoosterPack add-on boards, such

as graphical displays, audio codec, antenna selection, environmental sensing, and more. The

CC3200MODLAUNCHXL is provided as a complete platform solution including software, sample

applications, tools, user and programming guides, reference designs, and the TI E2E™ support

community. Figure 1 shows a photo of the CC3200MODLAUNCHXL board.

Visit the CC3200 Wiki page for design resources and example projects.

NOTE: The antennas used for this transmitter must be installed to provide a separation distance of

at least 20 cm from all persons, and must not be co-located or operating in conjunction with

any other antenna or transmitter.

1.2 Key Features

• FCC, IC, CE, and Wi-Fi® CERTIFIED™ modules, with ability to request certificate transfer for Wi-Fi

Alliance members

• CC3200MOD, SimpleLink Wi-Fi, internet-on-a-chip™ module solution with integrated MCU

• 40-pin LaunchPad standard that leverages the BoosterPack ecosystem

• FTDI-based JTAG emulation with serial port for flash programming

• Two buttons and three LEDs for user interaction

• Backchannel universal asynchronous receiver/transmitter (UART) through USB to PC

• On-board chip antenna with U.FL for conducted testing

• On-board accelerometer and temperature sensor for out-of-box demo

• Micro USB connector for power and debug connections

4CC3200MOD SimpleLink™ Microcontroller and Wi-Fi® Network Processor SWRU397–December 2014

Module - LaunchPad Hardware Submit Documentation Feedback

www.ti.com

Introduction

1.3 What's Included

Kit Contents:

• CC3200MODLAUNCHXL development board

• Micro USB cable

• Quick Start guide

1.4 FCC/IC Regulatory Compliance

The CC3200 SimpleLink Wi-Fi and IoT solution with MCU LaunchPad hardware is FCC Part 15 and IC

ICES-003 Class A compliant.

SimpleLink is a trademark of Texas Instruments.

SWRU397–December 2014 CC3200MOD SimpleLink™ Microcontroller and Wi-Fi® Network Processor

Module - LaunchPad Hardware

Hardware Description

www.ti.com

2 Hardware Description

Figure 1. CC3200MOD LaunchPad EVM Overview

6CC3200MOD SimpleLink™ Microcontroller and Wi-Fi® Network Processor SWRU397–December 2014

Module - LaunchPad Hardware Submit Documentation Feedback

www.ti.com

Hardware Description

2.1 Block Diagram

Figure 2. CC3200MOD LaunchPad Block Diagram

2.2 Hardware Features

• CC3200MOD, SimpleLink Wi-Fi, internet-on-a-chip module solution with integrated MCU40-pin

LaunchPad standard that leverages the BoosterPack ecosystem

• FTDI-based JTAG emulation with serial port for flash programming

• Supports both 4-wire JTAG and 2-wire SWD

• Two buttons and three LEDs for user interaction

• Virtual COM port UART through USB on PC

• On-board chip antenna with U.FL for conducted testing

• On-board accelerometer and temperature sensor for out-of-box demo with option to isolate them from

the inter-integrated circuit (I2C) bus

• Micro USB connector for power and debug connections

• Headers for current measurement and external JTAG connection

• Bus-powered device with no external power required for Wi-Fi

• Long range transmission with highly optimized antenna (200m typical in open air with a 6dBi antenna

AP)

• Can be powered externally, with 2xAA or 2xAAA alkaline batteries working down to 2.3V typical (typ)

SWRU397–December 2014 CC3200MOD SimpleLink™ Microcontroller and Wi-Fi® Network Processor

Module - LaunchPad Hardware

Hardware Description

www.ti.com

2.3 Connecting a BoosterPack

A compatible BoosterPack can be stacked on top of the LaunchPad using the 2x20 pin connectors. Note

that the connectors do not have a “key” to prevent the misalignment of the pins or reverse connection.

Ensure that the Vcc and 5V pins are aligned with the BoosterPack header pins. On the CC3200MOD

LaunchPad, a small white triangle symbol is provided near Pin-1 (see Figure 3) to orient all BoosterPacks.

This same marking, provided on compatible BoosterPacks, must be aligned before powering up the

boards.

Figure 3. Pn-1 Marking on the CC3200MOD LaunchPad (White Triangle)

2.4 Jumpers, Switches and LEDs

2.4.1 JTAG Headers

The headers are provided on the board to isolate the CC3200MOD device from the mounted FTDI JTAG

emulator. These jumpers are shorted by default when the board is shipped from TI. To connect an

external emulator, remove these jumpers and place the external emulator on the pins closer to the

CC3200MOD device.

Figure 4. JTAG Headers

Table 1. JTAG Headers

Reference Usage Comments

J8 (TCK) (1) JTAG Short : Routes the on-board emulator to the CC3200MOD.

J9 (TMS)(1)

J10 (TDI) Open: Isolates the on-board emulator from the CC3200MOD.

J11 (TDO)

(1) For the SWD mode, only TCK and TMS need to be shorted to the CC3200MOD.

When a battery is used, disconnect all JTAG headers to prevent any reverse leakage current.

8CC3200MOD SimpleLink™ Microcontroller and Wi-Fi® Network Processor SWRU397–December 2014

Module - LaunchPad Hardware Submit Documentation Feedback

www.ti.com

Hardware Description

2.4.2 I2C Connections

The board features an accelerometer and a temperature sensor for the out-of-box demo. These are

connected to the I2C bus and can be isolated using the jumpers provided.

Figure 5. I2C Connections

By removing J2 and J3, the accelerometer and the temperature sensors are isolated from the I2C bus.

Note that this also removes any pull-up resistor from the I2C bus.

2.4.2.1 Jumper Settings

Table 2. Jumper Settings

Reference Usage Comments

Short : Connect the CC3200MOD I2C bus to the on-board sensors with

J2 I2C SDA pull-up

Open : Isolate the sensors from the CC3200MOD

Short : Connect the CC3200MOD I2C bus to the on-board sensors with

J3 I2C SCL pull-up

Open : Isolate the sensors from the CC3200MOD

J4 INT Short : Connect the accelerometer interrupt to the CC3200 on GPIO13

2.4.2.2 Default I2C Address

Table 3. Default I2C Addresses

Sensor Type Ref Part Number Slave Address

Temp sensor U6 TMP008 0x41

Accelerometer U10 BMA222 0x18

2.4.3 Power Connections

The board can be powered by using the on-board micro USB connector. An on-board LDO provides 3.3 V

for the CC3200MOD and the rest of the board to operate. This supply can be isolated from the LDO using

the jumpers on the board.

Table 4. Jumper Settings

Reference Usage Comments

J12 Current measurement Measures the current flowing into the CC3200 device.

Short: Supply the board power from the on-board LDO.

J13 Board power Open: Supply the board power from the J20 (battery connector)

J19 5 V power 5 V output from the USB VBUS (has a diode drop of up to 0.4 V)

Can be used to power the board from an external 2XAA battery

J20 3.3 V power input pack. It has in-built reverse voltage protection to prevent the battery

from being plugged in the reverse manner.

SWRU397–December 2014 CC3200MOD SimpleLink™ Microcontroller and Wi-Fi® Network Processor

Module - LaunchPad Hardware

Hardware Description

www.ti.com

2.4.4 UART Signals

The board supports a USB-based virtual COM port, which is used on the FTDI device FT2232D. There

are two ports on the FT2232: the first port is dedicated for the emulation (JTAG/SWD), and the second

port is used for the virtual COM port. The UART can also be routed to the 20-pin connector and the

selection is performed using jumpers on the board.

Figure 6. UART Signals

Table 5. UART Signals

Reference Usage Comments

Short 1-2: Route the signals to the 20 pin connector.

J6, J7 UART for Flash programming Short 2-3: Route the signals to the FTDI for Flash programming.

2.4.5 Sense on Power

The CC3200MOD can be set to operate in three different modes based on the state of the Sense on

Power (SOP) lines. These are pins 21, 34, and 35 on the CC3200MOD device. The state of the device is

described in Table 6.

Table 6. SOP Lines

Usage Comments

100 = Flash programming

SOP[2:0] 000 = Functional mode + 4 Wire JTAG

001 = Functional mode + 2 Wire JTAG

Note: SOP[2:0] corresponds to J15, J16, and J17, in the LaunchPad schematic design.

Figure 7. SOP Jumpers

10 CC3200MOD SimpleLink™ Microcontroller and Wi-Fi® Network Processor SWRU397–December 2014

Module - LaunchPad Hardware Submit Documentation Feedback

Tabla de contenidos

Otros manuales de Placa madre de Texas Instruments

Texas Instruments

Texas Instruments LM5161PWPBKEVM Manual de usuario

Texas Instruments

Texas Instruments BQ25710EVM-017 Manual de usuario

Texas Instruments

Texas Instruments TMP392EVM Manual de usuario

Texas Instruments

Texas Instruments TPS40100 Manual de usuario

Texas Instruments

Texas Instruments ADS9817 Manual de usuario

Texas Instruments

Texas Instruments THS4150 Manual de usuario

Texas Instruments

Texas Instruments TPS6236 EVM-655 Series Manual de usuario

Texas Instruments

Texas Instruments TPS61130EVM Manual de usuario

Texas Instruments

Texas Instruments GC5325 Manual de usuario

Texas Instruments

Texas Instruments LM5171-Q1 Manual de usuario

Texas Instruments

Texas Instruments UA78LEVM-075 Manual de usuario

Texas Instruments

Texas Instruments DS80PCI810EVM Manual de usuario

Texas Instruments

Texas Instruments BOOST-DAC8730-HART Manual de usuario

Texas Instruments

Texas Instruments DLP471TEEVM Manual de usuario

Texas Instruments

Texas Instruments LP2951EVM Manual de usuario

Texas Instruments

Texas Instruments MSC1211EVM Manual de usuario

Texas Instruments

Texas Instruments TAS5780M Manual de usuario

Texas Instruments

Texas Instruments DS320PR810-RSC-EVM Manual de usuario

Texas Instruments

Texas Instruments LMP91051EVM Manual de usuario

Texas Instruments

Texas Instruments TPS2553Q1EVM Manual de usuario

Texas Instruments

Texas Instruments TPS56121 Manual de usuario

Texas Instruments

Texas Instruments TPS63070EVM-693 Manual de usuario

Texas Instruments

Texas Instruments DRV8410EVM Manual de usuario

Texas Instruments

Texas Instruments TPD1E01B04 Manual de usuario

Manuales populares de Placa madre de otras marcas

DFI

DFI SD170 Manual de usuario

ASROCK

ASROCK ROMED8-2T Manual de usuario

Asus

Asus P2L97A Manual de usuario

Winmate

Winmate IC70 Manual de usuario

Asus

Asus MES-B Manual de usuario

Grantech

Grantech SYS8F377VGGA-3OMN Manual de usuario

Telit Wireless Solutions

Telit Wireless Solutions SL869-3DR Manual de usuario

Gigabyte

Gigabyte GA-9IVDT Manual de usuario

Commell

Commell MS-C73 Manual de usuario

IBT Technologies

IBT Technologies MB860 Manual de usuario

Nvidia

Nvidia TEGRA DG-04927-001_V01 Manual de usuario

Biostar

Biostar M7VIT Bravo Instrucciones de funcionamiento e instalación

Intel

Intel D33217CK Manual de usuario

Asus

Asus F1A55-M LX PLUS R2.0 Manual de usuario

EPC

EPC EPC9147C Manual de usuario

Asus

Asus EX-B760M-V5 D4 Manual de usuario

EPOX

EPOX MU-8KHA0010 Manual de usuario

Ski-Doo

Ski-Doo Bombardier MPEM 219 700 090 Manual de usuario