Texas Instruments ADC366 EVM Series Manual de usuario

User’s Guide

ADC366xEVM Evaluation Module

Abstract

This user’s guide describes the characteristics, operation, and use of the ADC366x evaluation module (EVM).

This user's guide discusses how to set up and configure the software and hardware, and reviews various

aspects of the program operation. Throughout this document, the terms evaluation board, evaluation module,

and EVM are synonymous with the ADC366xEVM. In the following sections of this document, the ADC366x

evaluation board is referred to as the EVM and the ADC366x devices are referred to as the ADC devices,

respectively. This document applies only to the ADC3663EVM and ADC3662EVM.

Table of Contents

Abstract...................................................................................................................................................................................... 1

1 Introduction.............................................................................................................................................................................2

2 Equipment............................................................................................................................................................................... 2

2.1 ADC366xEVM Functionality...............................................................................................................................................2

2.2 Evaluation Board Feature Identification Summary.............................................................................................................4

2.3 Required Equipment.......................................................................................................................................................... 5

3 Setup Procedure..................................................................................................................................................................... 6

3.1 Install High-Speed Data Converter (HSDC) Pro Software................................................................................................. 6

3.2 Install ADC35XXEVM GUI 1.0 Software............................................................................................................................ 6

3.3 Connect the ADC366xEVM and TSW1400EVM................................................................................................................6

3.4 Connect the Power Supply and Mini-USB Connections.................................................................................................... 7

3.5 Connect the Clocks and Analog Input................................................................................................................................7

4 ADC GUI Configuration.......................................................................................................................................................... 8

4.1 Bypass Mode..................................................................................................................................................................... 9

4.2 Real Decimation Mode.....................................................................................................................................................13

4.3 Complex Decimation Mode.............................................................................................................................................. 16

5 Onboard Clocking Hardware Setup.................................................................................................................................... 19

5.1 Onboard Clocking: Hardware Modfications......................................................................................................................20

5.2 Onboard Clock: ADC35XX GUI Real Decimation Mode ................................................................................................. 22

6 FDA Configuration................................................................................................................................................................23

7 ADC36xxEVM Power Monitor.............................................................................................................................................. 25

8 Test Pattern........................................................................................................................................................................... 26

www.ti.com Abstract

SBAU366 – JANUARY 2021

Submit Document Feedback

ADC366xEVM Evaluation Module 1

1 Introduction

The ADC366xEVM is an evaluation board used to evaluate the ADC366x analog-to-digital converters (ADC)

from Texas Instruments. The ADC366x uses a serial LVDS interface to output the digital data. The serialized

LVDS interface supports output rates to 1 Gbps. The ADC366x can be operated in 'oversampling + decimating'

mode using the internal decimation filter in order to improve the dynamic range and relax external anti-aliasing

filter.

The ADC366xEVM is equipped with the following features:

• Transformer and FDA coupled analog inputs

• CDCE6214 clocking solution for on-board clocking

• Transformer coupled or single-ended clock inputs

• INA226 current shunt monitors for evaluating power consumption

• Power over mini-USB

• FMC connector

By default, the EVM is configured to receive external inputs for the sampling clock and analog input via AC-

coupled, transformer (balun) inputs. These transformers perform single-ended to differential conversion, and

provide a low noise/distortion passive input.

To exercise the full performance capabilities of this high performance SAR ADC, it is recommended to evaluate

the ADC in the default configuration, and then evaluate in other configurations (like onboard clocking or FDA

input), as required.

2 Equipment

This hardware setup procedure is written with the intent to use external clocking (sample clock and DCLKIN) and

transformer coupled analog inputs. Using onboard clocking and FDA driven analog inputs is an option, and

instructions are provided toward the end of this document to make the required hardware/software modifications.

2.1 ADC366xEVM Functionality

The ADC366xEVM receives power from the USB 2.0, +5 V rail, and is then converted to +3.3 VDC and +1.8

VDC. The ADC receives +1.8 VDC from the TPS62231 DC-DC converter. The power consumption of the 1.8 V

rail can be monitored (using the INA226) in the ADC35xxEVM GUI. USB-to-SPI communication is established

using the FTDI (FT4234H). The ADC clocks can be supplied externally or from the onboard PLL/Distributor

CDCE6214 (high quality external clocks are used to acheive best AC performance). The analog input can be AC

coupled through the Balun (ADT1-6T+) input, or DC (or AC) coupled with the onboard FDA (THS4541). The

analog input is 3.2 Vpp, and is driven a -1 dBFS (~2.8 Vpp) in all examples in this user's guide.

The ADC366x family has a +1.6 V voltage reference (VREF), and can be supplied internally or externally. By

default, the EVM is configured to supply an external voltage reference using the REF3318 (divided down to +1.6

V) and the OPA837 high speed amplifier to drive the voltage reference. At any time, the VREF can be changed

to internal reference by SPI write.

The ADC366x family uses an unbuffered analog input, so a glitch filter is required to attenuate the ADC sampling

glitch from when the sampling capacitors switch (sample/hold). The glitch filter acts as a low pass filter with an

corner frequency (Fc) at 30 MHz (accepts DC to 30 MHz).

The ADC366xEVM LVDS output data is routed to an FMC connector, and then connected to the LVDS

Interposer card. This interposer card then maps to the TSW1400EVM HSMC connector in order to capture the

ADC366xEVM SLVDS clock and data signals.

Introduction www.ti.com

2ADC366xEVM Evaluation Module SBAU366 – JANUARY 2021

Submit Document Feedback

Figure 2-1. ADC36xxEVM block diagram: Balun input

Figure 2-2. ADC36xxEVM block diagram: FDA input

www.ti.com Equipment

SBAU366 – JANUARY 2021

Submit Document Feedback

ADC366xEVM Evaluation Module 3

2.2 Evaluation Board Feature Identification Summary

Figure 2-3. ADC366xEVM Feature Identification

Ensure that jumper J16 is shunted in the 2-3 position. This allows 5 V to be supplied to the ADC366xEVM

through the mini-USB connector.

If an external 5-V supply is desired, J16 must be shunted in the 1-2 position, and the external 5 V can be

connected to the test point labeled "+5 EXT". The USB data connection is still connected for SPI

communications.

J13 is tied to the REFBUF pin. It can be left floating, or can be tied to 1.8 V (shunt pins 2-3) for normal operation.

J14 is tied to the PDN/SYNC pin. It can be left floating for tied to ground (shunt pins 1-2) for normal operation. To

power down the ADC, tied to 1.8 V (shunt pins 2-3). The ADC may also be powered down via SPI.

Equipment www.ti.com

4ADC366xEVM Evaluation Module SBAU366 – JANUARY 2021

Submit Document Feedback

Figure 2-4. LVDS Interposer

2.3 Required Equipment

• The following equipment is included in the EVM evaluation kit:

– ADC366xEVM Evaluation board (EVM)

– LVDS FPGA Interposer Card

– Mini-USB cable

The following equipment is not included in the EVM evaluation kit, but is required for evaluation of this EVM:

• TSW1400EVM data capture board and related items

•HSDC Pro software

• PC running Microsoft® Windows® 7, or 10

• One low-noise signal generator for the analog input (If using onboard clock option, no additiona signal

generators are required).

• Two low-noise signal generators for the sample clock and DCLKIN. (These two signal generators must share

the same reference frequency).

TI recommends the following generators:

• Rohde & Schwarz SMA100A

• Rohde & Schwarz SMA100B

A bandpass filter is required for the analog input signal due to most signal generators addition of phase noise or

spurious components. A bandpass filter should also be used for the sample clock input. The DCLKIN input does

not require a bandpass filter. If bandpass filters are not used, then the true performance of the ADC may not be

seen clearly, and is limited by the performance of the signal generators being used.

The following recommended bandpass filter have:

• Bandpass filter, greater than or equal to 60-dB harmonic attenuation, less than or equal to 5% bandwidth,

greater than 18-dBm power, less than 5-dB insertion loss

• Signal-path cables, SMA

www.ti.com Equipment

SBAU366 – JANUARY 2021

Submit Document Feedback

ADC366xEVM Evaluation Module 5

3 Setup Procedure

This Setup Procedure will detail how to setup the ADC366xEVM hardware and software GUI required for

evaluation using external sample and DCLKIN clocks. The clock rates in the following steps apply specifically to

the ADC3663EVM, but example clock rates are provided for other EVM variants.

3.1 Install High-Speed Data Converter (HSDC) Pro Software

Download the most recent version of the HSDC Pro software. Launch the executable, and accept the default

installation options.

3.2 Install ADC35XXEVM GUI 1.0 Software

Download the ADC35XXEVM GUI 1.0 software from the EVM tool folder at ADC3663EVM.

Extract and run the executable file, and accept the default installation options.

3.3 Connect the ADC366xEVM and TSW1400EVM

Connect the ADC366xEVM FMC connector to J4 of the LVDS Interposer Card.

Connect J5 of the LVDS Interposer Card to J1 of the TSW1400EVM.

Figure 3-1. ADC366xEVM Complete Setup (external clocks)

Setup Procedure www.ti.com

6ADC366xEVM Evaluation Module SBAU366 – JANUARY 2021

Submit Document Feedback

3.4 Connect the Power Supply and Mini-USB Connections

Use the following steps to connect the power supply and mini-USB connections:

1. Connect the power cable to the TSW1400EVM at 5-V (minimum 3 A) power supply. Place the power switch

(SW7) to the "On" position.

2. Connect the mini-USB cable to the TSW1400EVM (J2).

3. Connect the mini-USB cable to the ADC366xEVM (J16).

3.5 Connect the Clocks and Analog Input

Use the following steps to connect the external ADC clocks and analog input. If onboard clocking is to be used,

follow the instructions in the section Onboard Clocking Hardware Setup.

The clock frequencies shown below are for the power on/default settings (bypass mode/non-decimation) for the

ADC3663EVM, but the physical connections and signal power levels will remain the same for all ADC modes.

• For the sample clock (ADC3663EVM), set a signal generator to 65 MHz at a power level of +10 dBm.

Connect to the SMA connector J4. A bandpass filter for the sample clock is recommended for best AC

performance of the ADC366xEVM.

• For the DCLKIN clock (ADC3663EVM), set a signal generator to 260 MHz at a power level of +10 dBm. A

bandpass filter is not required for the DCLKIN clock.

External ADC sampling clock source and DCLKIN source must be frequency locked. If this is not

performed, the captured data will appear scrambled. If using the onboard clocking option, the

sampling clock and DCLKIN are frequency locked.

• For the analog input, set a signal generator to 5 MHz at a power level of ~ +15 dBm. A bandpass filter is

required to reduce harmonic and phase noise effects of the signal generator.

www.ti.com Setup Procedure

SBAU366 – JANUARY 2021

Submit Document Feedback

ADC366xEVM Evaluation Module 7

4 ADC GUI Configuration

A hardware reset should be performed before programming the ADC by toggling the push button switch S1.

Also, a software reset may be performed at any time to reset the ADC registers to their default state.

Figure 4-1. ADC35xx Software Reset

ADC GUI Configuration www.ti.com

8ADC366xEVM Evaluation Module SBAU366 – JANUARY 2021

Submit Document Feedback

4.1 Bypass Mode

The following steps show how to configure the ADC366xEVM in Bypass mode with external sample clock and

DCLKIN. These instructions show how to configure the ADC3663EVM, but apply to other EVM variants as well.

4.1.1 ADC35XXEVM GUI: Bypass Mode (2W) Configuration

The following steps for Bypass (No Decimation)mode also apply to ADC3662EVM, but requires modification to

the sample/DCLKIN clocks in accordance with the desired sample rate and bit resolution. For example, at 25

MSPS, the DCLKIN rate is 25 MHz x 4 = 100 MHz.

For different sampling rates and bit resolutions, see Table 4-1 for calculating the correct DCLKIN frequency for

the desired sample rate and bit resolution.

Table 4-1. 16-bit, Bypass Mode, Sample rate and DCLKIN examples (ADC3663EVM, ADC3662EVM).

Interface Mode DCLKIN multiplier Example Sample Clock Required DCLKIN Frequency

2 Wire 4 65 MSPS 260 MHz

1 Wire 8 32 MSPS 256 MHz

1/2 Wire 16 10 MSPS 160 MHz

For this example, ensure that the sampling clock (J9) and DCLKIN (J7) are connected before launching the

ADC35XX EVM GUI. In this example, for the ADC3663EVM, the sampling clock is 65 MHz, and the DCLKIN is

292.5 MHz.

External ADC sampling clock source and DCLKIN source must be frequency locked. If this is not

performed, the captured data appears scrambled. If using the onboard clocking option, the sampling

clock and DCLKIN are frequency locked.

After launching the ADC35xx GUI perform the following steps:

• Under Resolution, select "16 bit".

• Under Mode, select "2 Wire".

• Ensure that "CDC Enable" is red (disabled).

• To calculate the DCLKIN frequency, enter "65" in the Fs(MHz) field, and click calculate. This is informational

only.

• Click "Configure" button.

www.ti.com ADC GUI Configuration

SBAU366 – JANUARY 2021

Submit Document Feedback

ADC366xEVM Evaluation Module 9

Figure 4-2. ADC35XXEVM GUI: ADC3663 Bypass Mode

ADC GUI Configuration www.ti.com

10 ADC366xEVM Evaluation Module SBAU366 – JANUARY 2021

Submit Document Feedback

Este manual sirve para los siguientes modelos

Tabla de contenidos

Otros manuales de Placa madre de Texas Instruments

Texas Instruments

Texas Instruments TPSM8D6C24 Manual de usuario

Texas Instruments

Texas Instruments DRV8328A Manual de usuario

Texas Instruments

Texas Instruments TPS7A14EVM Manual de usuario

Texas Instruments

Texas Instruments CC1110EMK Manual de usuario

Texas Instruments

Texas Instruments WR1843 Series Manual de usuario

Texas Instruments

Texas Instruments TPS560200 Manual de usuario

Texas Instruments

Texas Instruments DRV8702-Q1 Manual de usuario

Texas Instruments

Texas Instruments ADCx120Q1EVM-PDK Manual de usuario

Texas Instruments

Texas Instruments DLP LightCrafter 6500 Manual de usuario

Texas Instruments

Texas Instruments Stellaris LM3S9B90 Manual

Texas Instruments

Texas Instruments TAS6421-Q1 EVM Manual de usuario

Texas Instruments

Texas Instruments DLP471TEEVM Manual de usuario

Texas Instruments

Texas Instruments ADS8860EVM-PDK Manual de usuario

Texas Instruments

Texas Instruments DAC3XJ8XEVM Manual de usuario

Texas Instruments

Texas Instruments TMAG5328 Manual de usuario

Texas Instruments

Texas Instruments AM572x series Manual de usuario

Texas Instruments

Texas Instruments TMAG5110-5111EVM Manual de usuario

Texas Instruments

Texas Instruments ADS1258EVM-PDK Manual de usuario

Texas Instruments

Texas Instruments TPS769 Series Manual de usuario

Texas Instruments

Texas Instruments WL1837MODCOM8I Manual de usuario

Texas Instruments

Texas Instruments BQ27620 Manual de usuario

Texas Instruments

Texas Instruments ADS58H4 Series Manual de usuario

Texas Instruments

Texas Instruments INA290EVM Manual de usuario

Texas Instruments

Texas Instruments TPA3244EVM Manual de usuario

Manuales populares de Placa madre de otras marcas

DFI

DFI SD170 Manual de usuario

ASROCK

ASROCK ROMED8-2T Manual de usuario

Asus

Asus P2L97A Manual de usuario

Winmate

Winmate IC70 Manual de usuario

Asus

Asus MES-B Manual de usuario

Grantech

Grantech SYS8F377VGGA-3OMN Manual de usuario

Telit Wireless Solutions

Telit Wireless Solutions SL869-3DR Manual de usuario

Gigabyte

Gigabyte GA-9IVDT Manual de usuario

Commell

Commell MS-C73 Manual de usuario

IBT Technologies

IBT Technologies MB860 Manual de usuario

Nvidia

Nvidia TEGRA DG-04927-001_V01 Manual de usuario

Biostar

Biostar M7VIT Bravo Instrucciones de funcionamiento e instalación

Intel

Intel D33217CK Manual de usuario

Asus

Asus F1A55-M LX PLUS R2.0 Manual de usuario

EPC

EPC EPC9147C Manual de usuario

Asus

Asus EX-B760M-V5 D4 Manual de usuario

EPOX

EPOX MU-8KHA0010 Manual de usuario

Ski-Doo

Ski-Doo Bombardier MPEM 219 700 090 Manual de usuario