Testrite Visual XSD Series Manual de usuario

Page 1 of 5Version: 3

Page 1 - Assemble the Frame

First start by assembling corners. There are three (2) brackets per corner. All extrusion sections are numbered

to identify which pieces go together, 1 with 1, 2 with 2, etc.

1. Insert the bent bracket into the extrusion where shown. Tighten the rst screw on the bracket ~75% only.

Take the mating extrusion piece with matching number, guide the corner brackets in and tighten the

second pair of screws ~75%. Do not fully tighten.

2. Repeat assembly steps for the three remaining corners. Fully tighten all bracket screws.

3. For larger boxes, sides may be built in multiple sections. These sections end in a straight cut (NOT a 45⁰

angle). Use the two (2) straight brackets to connect the two adjoining sections. The screws will be tightened

from the inside of the frame. Sections can be identied with matching numbers.

4. If provided, place center support bar bracket into frame channel and use the Allen key to expand the

bracket inside the channel to secure it in place.

Charisma™ LED Double Sided Light Box - XSD Series

1a.

Corner 4

Corner 3

Corner 2

1c.

1b. Tighten screws only ~75%

Tighten

screws only

~75%

Fully tighten

all bracket

screws

3a.

3b.

Support Bar

Page 2 of 5Version: 3

Page 2 - Connect Electrical Components

1. At each break in the extrusion, identify the orange or white electrical connector. Then connect the white female

connectors to their matching male connectors and the orange female connector to their matching male connector.

The connectors must fully“click” together.

2. It is normal for the last female white connector to be unconnected to anything else.

3. If there are multiple cables, connect those with matching colors.

Charisma™ LED Double Sided Light Box - XSD Series

ELECTRICAL NOTE:

This sign is intended to be

installed in accordance with the

requirements of Article 600 of

the National Electrical Code and/

or other applicable codes. This

includes proper grounding and

bonding of the sign.

Unconnected last female

connector is normal

1a.

1b.

Light Strip to

Light Strip

First Light Strip to

Power Supply

Power Supply to Plug

Page 3 of 5Version: 3

Page 3 - Mounting

1. HANG: the frame using the pre-mounted eyebolts, after installing graphic (see next page for graphic installation).

2. BASES: Mount the frame to the bases using the hardware provided.

CAUTION: Always ensure the frame is secured strongly without risk of falling before completing the installation.

Charisma™ LED Double Sided Light Box - XSD Series

1. 2.

Page 4 of 5Version: 3

Page 4 - Install the Graphic

1. Plug frame into wall outlet.

2. To install the graphic, take the corner with the pull tag on it and press about 6”-10”of silicone into the frame channel

corner A. Repeat for the opposite corner B. Repeat for the next corner C. Lastly, repeat for the nal corner D.

3. After all corners are pressed in, press the silicone into the frame channel at the mid-points on all four sides.

4. Press silicone into frame evenly between the corner and midpoints.

This prevents the graphic from bunching up or stretching too much and will ensure a smooth and tight t.

5. Repeat steps 1-4 on the second side.

6. To remove the graphic from the frame, simply pull up on the pull tag.

NOTE: Model shown below may dier from your model, but assembly instructions remain the same.

Charisma™ LED Double Sided Light Box - XSD Series

Apull tag

Page 5 of 5Version: 3

Charisma™ LED Double Sided Light Box - XSD Series

Page 5 - Repair Instructions - Light Replacement:

1. Unplug unit from wall.

2. Remove thumb screws from light strip.

3. Unplug the light strip male/female connectors, then remove the light strip.

4. Put new strip on the channel, with the glide turned parallel to the channel and dip the glide

into the channel.

5. Reconnect the new light strip to the adjacent connections.

6. Tighten the thumb screws to secure the knobs. If a knob doesn’t engage, unscrew the glide

until it is almost o, then try again.

7. Plug in the unit.

ELECTRICAL NOTE:

This sign is intended to be

installed in accordance with the

requirements of Article 600 of

the National Electrical Code and/

or other applicable codes. This

includes proper grounding and

bonding of the sign.

1. 2. 3.

4. 5. 7.

Lift out after

disconnected

3a.

3b.

Otros manuales de Equipo de iluminación de Testrite Visual

Testrite Visual

Testrite Visual Charisma Inside-Out Light Box XSIO Series Manual de usuario

Testrite Visual

Testrite Visual Charisma SEG XSL Series Manual de usuario

Testrite Visual

Testrite Visual Charisma XBX Series Manual de usuario

Testrite Visual

Testrite Visual SupraSlim SnapFrame SUL Series Manual de usuario

Testrite Visual

Testrite Visual Charisma SEG 3D Lit XS Series Manual de usuario

Manuales populares de Equipo de iluminación de otras marcas

Brizo

Brizo 8SP-MU-4 Manual de usuario

LUCE&LIGHT

LUCE&LIGHT BROM 1.0 Manual de usuario

IKEA

IKEA BJÖRKSPIREA Manual de usuario

Laserworld

Laserworld Evolution Series ES-400RGB Manual de usuario

Alien

Alien RG STAR Manual de usuario

EuroLite

EuroLite LED B-40 Manual de usuario

Qazqa

Qazqa Suplux SL 3 Black 103062 Manual de usuario

Commercial Electric

Commercial Electric 54568141 Manual de usuario

CREE LIGHTING

CREE LIGHTING 304 Series Manual de usuario

Goobay

Goobay 49867 Manual de usuario

ECOMAN ITALIA

ECOMAN ITALIA LED T8 Manual de usuario

Alkalite

Alkalite Krypton KT-81 Manual de usuario

Clas Ohlson

Clas Ohlson GU10 Manual de usuario

DTS

DTS DELTA 10 F Manual de usuario

ring

ring Solar Steplight Manual de usuario

One Stop Gardens

One Stop Gardens 57696 Instrucciones de montaje

Chauvet DJ

Chauvet DJ COREpar UV120 ILS Manual de usuario

SIREM

SIREM Swimeo A2 Manual de usuario