Terra Bound Solutions 581-706 Manual de usuario

581-706 5” OD Arch Post Swing 8’ 6 Seat

IMPORTANT

PLEASE READ THESE INSTRUCTIONS BEFORE COMMENCING ASSEMBLY. All equipment

must be installed in accordance with these instructions. Check your shipment

against Bill of Lading and Parts list. Any missing or broken parts must be

reported to your distributor within 10 days of receipt of your order. When

properly installed and maintained, equipment will give many years of Safe,

Trouble-Free use. Periodically check for loose or broken parts. Loose bolts

must be tightened and broken parts must be replaced as they can possibly

create dangerous situations leading to unnecessary accidents. Resilient

Surfacing should be used under all playground equipment. Appropriate

publications, available at no charge, from the Consumer Product Safety

Commission, include “A Handbook for Public Playground Safety”. You can

receive your free copy by calling 1-301-504-7908.

PACKING LIST HARDWARE BAG

1 CTN Hardware Bag 12 585-521 3 ½” Swing Hanger

3 PIPE 583-211 3 ½” Top Rail 6 585-955 Cut Proof Belt Seat

2 WF 583-573 Center Arch Posts 12 317-140 4/0 Chain 5’6”

2 WF 583-572 End Arch Posts 24 585-901 S Hook

12 196-802 ½” x ½” Socket Set Screw

1 416-400 ¼” Socket Key

1 805-532 Warning Label

1 805-534 SportsPlay Label

1 Maintenance Checklist

1 CTN 3 PIPE 4 WF TOTAL PCS= 1 SKID 1019 # WT Class 70

581-706 5” OD Arch Post Swing 8’ 6 Seat

GENERAL FOOTING RECOMMENDATIONS

Diameter and depth of footings illustrated are satisfactory in most

applications for pipe sizes up to 2 3/8” diameter. Varying soil & climatic

conditions may require deeper and heavier footings in some areas. Check

local building codes.

Detail: Detail:

Permanent Installation Suggested Bracing Method

IF RESILIENT SURFACING IS TO BE LESS THAN 12”, THEN ADDITIONAL PIPE SHOULD BE

PUT IN CONCRETE TO MAINTAIN PROPER FINISH GRADE FOR EQUIPMENT.

USE AREA AND FOOTING LAYOUT:

581-706 5” OD Arch Post Swing 8’ 6 Seat

Single Axis Swings:

The Use/Fall Zone should extend to the front & rear, a minimum distance of

twice the height of the Top Rail above the resilient surfacing material. The

Use/Fall Zone to the sides should follow the general recommendations of six

feet minimum. This six-foot zone may overlap that of an adjacent swing

structure.

Rotating Swings:

The Use/Fall Zone should extend in all directions the length of the swing

plus six feet. The six-foot minimum fall zone from the supporting structure

also applies, and may overlap the six-foot zone of an adjacent swing

structure.

GENERAL MAINTENANCE INSTRUCTIONS:

Check MONTHLY for loose bolts, damaged or broken parts. Tighten and/or

replace immediately. On swings and any equipment that uses S-hooks and/or

Swing Hangers check the bearing surfaces for wear. Replace any parts that

show a reduction of 25% from the original size.

ASSEMBLY AND INSTALLATION:

NOTE: All threaded ends of bolts protruding beyond nuts must be cut off

and/or peened to eliminate sharp edges. No more than two threads

should extend beyond face of nut. All tubing must be hammered down to

conform to the curved underlying surface to eliminate catch points. DO

NOT tighten nuts more than hand-tight until entire assembly is

completed.

STEP #1: Assemble swing frame on side, on ground. If more than one section,

assemble section by section. Layout parts so that when frame is

erected, legs will be in approximately correct position.

581-706 5” OD Arch Post Swing 8’ 6 Seat

STEP #2: Remove swing hanger pendulums from the swing hanger assemblies. Using

S-hooks, attach seats to chain and chain to swing hanger pendulums.

Close the S-hooks to within .034” (1/32”) using S-hook pliers.

STEP #3: Assemble top portion of swing hangers on top rail following spacing on

page 1 diagram.

STEP #4:

Footing holes may be marked out and dug from footing layout, however,

it is easier to position swing in proper location, mark holes, move

swing aside, and dig holes.

STEP #5: Stand swing upright onto legs and brace in footing holes so that 2’ –

3’ of pipe will be under intended level of resilient surfacing and top

rail is at desired height.

STEP #6: Plumb and level entire unit. Tighten set screws by using short length

of pipe on end of socket key to add leverage. Pour concrete. Crown

surface. Wait 48 hours before removing braces and using equipment.

STEP #7: Attach assembled seats to swing hangers by reattaching the pendulums to

the swing hangers. Do not over tighten bolt on pendulum. Hangers must

move freely.

STEP #8: Attach warning label and Manufacturer’s Identification label to a clean

surface. The labels should be attached in a location where they are

clearly visible and legible and away from normal hand and foot

placement areas. The labels must be replaced if they become illegible,

destroyed or removed. Contact your SportsPlay distributor for

replacements.

Otros manuales de Columpio de Terra Bound Solutions

Terra Bound Solutions

Terra Bound Solutions 581-504 Manual de usuario

Manuales populares de Columpio de otras marcas

Ledon

Ledon 1185 Manual de usuario

Backyard

Backyard LITTLE BRUTUS 2051171 Manual de uso y cuidado

Component Playgrounds

Component Playgrounds CP-PS24-8x10 Manual de usuario

Kettler

Kettler 0S01053-0000 Manual de usuario

Lemeks

Lemeks Palmako MV70-3121-4 Manual del instalador

Lifetime

Lifetime 90143 Manual de usuario

Belleze

Belleze 014-HG-14340 Manual de usuario

Elvox

Elvox RS07 Manual de usuario

gartenpirat

gartenpirat Premium 4.2 GP1305 Manual de usuario

Taizhou Taiyan Swing

Taizhou Taiyan Swing 805-447 Manual de usuario

KidKraft

KidKraft LAUREL F29715 Manual de usuario

Plum

Plum Roloway Manual de usuario

Component Playgrounds

Component Playgrounds AF30 Manual de usuario

OOGarden

OOGarden FOSSA Manual de usuario

Lakeland Mills

Lakeland Mills CF1128 Manual de usuario

Backyard Discovery

Backyard Discovery MONTPELIER 30211F Manual de usuario

LifeSpan Kids

LifeSpan Kids AMBER PE83 Manual de usuario

SPORTSPOWER

SPORTSPOWER MSC- 4132 Instrucciones de instalación