Tennant T16 Manual de capacitación

IB 9008464 (07--2011) 1

INSTRUCTION BULLETIN

No. 9008464

Machine: T16

Published: 07--2011

Rev. 00

NOTE: DO NOT DISCARD the Parts List from the Instruction Bulletin. Place the

Parts List in the appropriate place in the machine manual for future

reference. Retaining the Parts List will make it easier to reorder

individual parts and will save the cost of ordering an entire kit.

NOTE: Numbers in parenthesis ( ) are reference numbers for parts listed in Bill of Materials.

Installation instructions for kit number 9008115

SYNOPSIS:

This kit contains the parts needed to replace the spray nozzle hose on T16 scrubbers.

Please follow step-by-step instructions.

SPECIAL TOOLS / CONSIDERATIONS: NONE

(Estimated time to complete: 1 hour)

PROTECT THE ENVIRONMENT

Please dispose of packaging materials, old machine components,

and hazardous fluids in an environmentally safe manner according

to local waste disposal regulations.

Always remember to recycle.

PREPARATION:

1. Completely empty the solution tank and the

recovery tank. Refer to the Operators Manual

for instructions how to empty both tanks.

2. Park the machine on a clean level surface,

turn off the machine, and remove the key.

FOR SAFETY: Before leaving or servicing

machine, stop on level surface, turn off

machine, and remove key.

3. Disconnect the battery cables from the

batteries.

WARNING: Always disconnect battery

cables from machine before working on

electrical components.

4. Disconnect the main wire harness from the

vacuum fan assembly.

5. Remove the vacuum fan assembly from the

back end of the machine. Set the vacuum fan

assembly and hardware aside.

6. Remove the cable clamp securing the 35”

solution supply hose to the spray nozzle

assembly. Set the cable clamp aside and M8

hex screw aside. Refer to Fig. 1.

7. Disconnect the 35” solution supply hose from

the spray nozzle assembly. Set the hose

clamp aside. Refer to Fig. 1.

8. Remove the rotary fitting from the spray

nozzle assembly. Set the rotary fitting aside.

Refer to Fig. 1.

9. Use a cable tie (2) to secure the reel

assembly to the mounting plate. Refer to

Fig. 1.

10. Remove the spray nozzle assembly from the

machine. Set the M8 hex screws aside. Refer

to Fig. 1.

11. Remove the hose from the spray nozzle

assembly. Set the hose clamp aside. Refer to

Fig. 1.

12. Remove the spray nozzle gun and fitting from

the hose. Set the spray nozzle gun and fitting

aside. Discard the hose. Refer to Fig. 1.

IB 9008464 (07--2011)2

Solution tank

Remove and set M8

hex screw and cable

clamp aside

35” solution

supply hose

from pump

Remove and

set hose

clamp aside

Remove and set M8

hex screws aside

Mounting

plate

Remove and set M8 hex

screw and cable clamp

aside

Remove spray nozzle

gun from hose. Set

spray nozzle gun aside

Disconnect spray nozzle hose

from spray nozzle assembly.

Set hose clamp aside

Remove fittings from hose.

Set fittings aside

Discard hose after

removing all components.

Replace with hose (1)

Reel assembly

Rotaryfitting

Usecabletie(2)to

secure reel assembly to

mounting plate

Reel

assembly

FIG. 1

INSTALLATION:

1. Install the fittings and spray nozzle gun onto

the new spray hose (1). Refer to Fig. 1.

NOTE:If necessary, use a soapy solution to to

make installing the fitting going into the spray

hose (1) easier.

2. Connect the spray hose (1) to the spray

nozzle assembly. Refer to Fig. 1.

3. Use the M8 hex screw and cable clamp to

secure the spray hose (1) to the spray nozzle

assembly reel. Refer to Fig. 1.

4. Wrap the spray hose (1) evenly onto the reel

assembly. Refer to Fig. 1.

IB 9008464 (07--2011) 3

5. Wind the spray hose (1) completely onto the

reel and rotate the spray hose assembly

mounting plate three complete turns clockwise

to set the spring tension. Refer to Fig. 2.

FIG. 2

6. Use two cable ties (2) to secure the reel

assembly and spray hose (1) to the mounting

plate. Refer to Fig. 3.

FIG. 3

NOTE:Do Not cut the cable ties (2) holding the

spray hose into the spray hose reel until after the

spray hose assembly is installed onto the

machine. The spray hose could unwind from the

spray nozzle assembly if the cable ties are cut

before the spray nozzle assembly is reinstalled

onto the machine, making it necessary to repeat

Step 4 through Step 6 to reset the spring tension.

7. Reinstall the spray hose assembly onto the

solution tank. Refer to FIg. 1.

8. Reinstall the rotary fitting onto the spray

nozzle assembly. Refer to FIg. 1.

9. Use the hose clamp to reconnect the 35”

solution supply hose to the rotary fitting. Refer

to FIg. 1.

10. Use the cable clamp and M8 hex screw to

secure the 35” solution supply hose to the

spray nozzle assembly. Refer to Fig. 1.

11. Cut the cable ties (2) from the reel assembly.

Refer to FIg. 1.

12. Reinstall the vacuum fan assembly onto the

machine and reconnect the wire harness to

the vacuum fan assembly.

13. Reconnect the battery cables to the batteries.

14. Start and test the machine. Fill the solution

tank. Turn on and operate the spray nozzle to

ensure it functions. Refer to the Operators

Manual for instructions how to use the spray

nozzle.

Bill Of Materials For Hose Kit, Replmt [T16] -- 9008115

Ref.

Tennant

Part No. Description Qty.

o9008115 )Hose Kit, Replmt [T16] 1

Y1 1061087 Hose, Rbr, 0.38ID, Bulk, Blk [Push--Lok] 1

Y244961 Tie, Cable, Nyl, 14.5L .30W 4.0 Max D 3

TENNANT COMPANY

P. O. Box 1452

Minneapolis, MN 55440-1452

Otros manuales para T16

Otros manuales de Depurador de Tennant

Tennant

Tennant 7200 Manual de usuario

Tennant

Tennant 9021147 Manual de usuario

Tennant

Tennant M17 Series Manual de capacitación

Tennant

Tennant T20 LPG Manual de usuario

Tennant

Tennant T16 Manual de capacitación

Tennant

Tennant IRIS T300 Manual de usuario

Tennant

Tennant Nobles WB-20B Manual del producto

Tennant

Tennant 5400 Manual de usuario

Tennant

Tennant SweepSmart S20 ELECTRIC Manual de capacitación

Tennant

Tennant T291 Manual de usuario

Tennant

Tennant CS5 Manual de funcionamiento

Tennant

Tennant T15 Instrucciones de funcionamiento e instalación

Tennant

Tennant 5100 Manual del producto

Tennant

Tennant T300e Manual de usuario

Tennant

Tennant 7400 Manual de usuario

Tennant

Tennant L2 Manual de usuario

Tennant

Tennant 5700XP Manual de usuario

Tennant

Tennant M30 Manual de usuario

Tennant

Tennant 5700 Manual de usuario

Tennant

Tennant CS16 Manual de usuario

Tennant

Tennant T600e Manual de usuario

Tennant

Tennant 800D Manual de usuario

Tennant

Tennant 800 Manual de usuario

Tennant

Tennant M17 Series Manual de capacitación

Manuales populares de Depurador de otras marcas

Olympus

Olympus M200H Manual de usuario

Clarke

Clarke BEXT 100H Manual de instalación y funcionamiento

JOHNY VAC

JOHNY VAC JVC70BCT Manual de usuario

RCm

RCm Elan Series Manual

Kärcher

Kärcher B 120 W Manual de usuario

Truvox

Truvox Orbis MotorScrubber 20 Manual de usuario

Numatic

Numatic TTB 4045/100 Manual de usuario

U.S. Products

U.S. Products PEX 500-C-TICK Instrucciones de funcionamiento

Mclennan

Mclennan C510 Manual de usuario

Columbus

Columbus ARA 66 BM 100 Manual de usuario

Numatic

Numatic TTV 678G / 300T Manual de usuario

American-Lincoln

American-Lincoln 505-945 Manual de usuario

FIORENTINI

FIORENTINI ET 65-75 Manual de usuario

Floorpul

Floorpul ruby 48 blt Guía del usuario

Onyx

Onyx RX-34 Manual de usuario

Dustbane

Dustbane Hurricane 400 Manual de usuario

Sana

Sana EUJ-702 Manual de usuario

REMS

REMS Twist Manual de usuario