Tennant 8300 Manual de capacitación

IB 340485 (03--2010) 1

No. 340485

Machine: 8300

Published: 03--2010

Rev: 01

INSTRUCTION BULLETIN

NOTE: DO NOT DISCARD the Parts List from the Instruction Bulletin. Place the Parts

List in the appropriate place in the machine manual for future reference.

Retaining the Parts List will make it easier to reorder individual parts and will

save the cost of ordering an entire kit.

NOTE: Numbers in parenthesis ( ) are reference numbers for parts listed in Bill of Materials.

Installation instructions for kit number 387548 / 9006965

SYNOPSIS:

This kit contains the parts needed to install an update/retrofit kit on the 8300 sweeper/scrubber.

Please follow step-by-step instructions.

SPECIAL TOOLS / CONSIDERATIONS: NONE

(Estimated time to complete: 5 hours)

FIELD ENGINEERING REPORT DETAILS: It is possible for water or moisture to wick itself between the

touch panel material layers. This can cause traces on the touch panel to corrode and short the

backlighting and digital system circuits. The circuit board could also be damaged.

PREPARATION:

(Refer to Fig. 1 through Fig. 6)

SECTION 1:

7300/8300 TOUCH PANEL/CIRCUIT BOARD MOISTURE / CORROSION INSPECTION: (TSB No. 017300--00)

FOR SAFETY: Before leaving or servicing machine, stop on level surface, set parking brake, turn off

machine, and remove key.

1. Disconnect battery cables from the batteries.

WARNING: Always disconnect battery cables from machine before working on electrical

components.

2. Remove the touch panel from the machine instrument panel housing.

3. Remove the surrounding rubber bezel. (Refer to FIG. 1)

4. Inspect the lower outside perimeter of the touch panel assembly for green copper oxide formations. Refer to

Fig. 1.

5. Replace the touch panel assembly if excessive corrosion is found.

6. If the touch panel assembly does not need to be replaced, add clear dielectic grease (TENNANT PN# 86385)

to the lower outside perimeter of the touch panel.

7. Clean the inside channel of the bezel and attach the bezel to the touch panel assembly. Wipe any exposed

dielectic grease from the assembly surfaces.

8. Ensure the switch plugs did not pull away from switches, before reinstalling touch panel. Reconnect the touch

panel and the battery cables to the machine.

9. Check the machine functions and run the self test.

IB 340485 (03--2010)2

NOTE: If excessive corrosion is found, and a new panel must be ordered, the machine can be kept operational

by disconnecting and taping 21ORA wire from the backlighting touch panel circuit (backlighting will be

inoperative). This will also prevent damage to the circuit board while waiting for a new touch panel to be

installed.

NOTE: If replacing the touch panel, be sure the new panel edge is treated with a coating before installing.

Inspect all along the lower

edge for green copper oxide.

Remove the rubber bezel from

the edge of the touch panel.

FIG. 1 -- Control Panel Inspection

IB 340485 (03--2010) 3

SECTION 2:

INSTALLATION:

(Refer to Fig. 2 and Fig. 3)

NOTE: Machines with serial numbers after 003053 are already equipped with correct fuses and propel cable.

Check all connection hardware for tightness and proceed to section 3.

FOR SAFETY: Before leaving or servicing machine, stop on level surface and set parking

brake. Then turn off machine and remove key.

1. Secure rear machine cover open with the cover support rod.

2. Disconnect battery cables from the batteries.

WARNING: Always disconnect battery cables from machine before working

on electrical components.

3. Secure side cover on the left side of the machine open with the cover support rod.

4. Open the side door on the left side of the machine.

5. Remove and set aside the detergent tank (option) if necessary.

6. Remove and set aside the contactor cover.

7. Remove the drive motor cover panel from inside the operator compartment. Set the panel and mounting

hardware aside.

8. Label or note how all propel motor wires are routed and tied before disconnecting.

NOTE: Once the new hardware and cables are installed, all motor wires must be routed and tied as shown in

Fig. 3.

8. Disconnect and remove both 2 gauge and both 4

gauge wires from the propel motor. Leave the terminal

nuts on the posts close to the motor. Disconnect the

other ends of the 4 gauge wires from the contactor.

Disconnect the other ends of the 2 gauge wires from

the motor controller. Remove and discard the propel

motor wires.

IB 340485 (03--2010)4

9. Connect each new 4 gauge wire (5), to each of the

lower posts (S1 and S2) on the propel motor, with new

nuts (6), flat washers (7), and lock washers (8) as

shown in Fig. 2. Hand tighten the mounting hardware.

1. Carefully route the 4 gauge wire from post S1 to the

inside contactor. Route the 4 gauge wire from post S2

to the outside contactor. Connect the wires to the

contactors with new lock washers (11), flat washers

(10), and nuts (9) as shown in Fig. 2. Hand tighten the

mounting hardware.

2. Connect each new 2 gauge wire (4), to each of the top

posts (A1 and A2) on the propel motor, with new nuts

(6), flat washers (7), and lock washers (8) as shown in

Fig. 2. Hand tighten the mounting hardware.

3. Carefully route the 2 gauge wire from post A1 to the

inside post on the motor controller. Route the 2 gauge

wire from post A2 to the outside post on the motor

controller. Connect the wires to the posts on the motor

controller with set aside hardware as shown in Fig. 2.

Hand tighten the mounting hardware.

A1 A2

From S1

From S2

A1 A2

From A2

From A1

IB 340485 (03--2010) 5

FIG. 2 -- New Cable And Hardware Installation, Propel Motor

(Refer to FIG. 3 for cable routing)

IB 340485 (03--2010)6

FIG. 3 -- New Cable Routing, Propel Motor

9. Be sure all new motor wires are routed the same way as shown in Fig. 3.

NOTE: All motor wires must be routed and tied as shown in Fig. 3.

10. Tighten all mounting hardware to 125 in. lbs.

11. Slide any excess length of the 4 gauge wires into the panel box. Secure the new motor wires with wire ties.

Refer to Fig. 3.

12. Open the circuit board panel next to the motor and set the cover mounting hardware aside. Refer to Fig. 4.

13. Carefully label or note all ribbon cable mounting locations on both circuit boards.

14. Disconnect all ribbon cables from both circuit boards. Remove both circuit boards from the machine, and

place them on a clean work surface.

15. Replace the three 10A fuses in the two circuit boards with three new slo--blo 20A fuses. Refer to Fig. 4.

IB 340485 (03--2010) 7

Replace three 10A fuses with

three new 20A fuses

FIG. 4 -- Circuit Board Assembly

16. Install the circuit boards in the machine and reconnect all ribbon cables to the boards.

17. Close and secure the circuit board cover.

18. Reinstall the motor panel cover inside the operator compartment.

19. Reinstall the detergent tank (option) if removed.

20. Reinstall the contactor cover.

21. Close the side door and cover on the left side of the machine.

22. Reconnect the battery cables to the machine. Close the rear machine cover.

23. Turn the machine power on. Check the machine for proper operation.

IB 340485 (03--2010)8

SECTION 3:

MAXPRO 1000 VACUUMIZED SIDE SQUEEGEE INSTALLATION:

(Refer to IB 340474 for removal and installation of new vacuumized side squeegee)

1. Install the new vacuumized side squeegee. (Refer to INSTRUCTION BULLETIN 340474)

SECTION 4:

MAXPRO 1000 REAR SQUEEGEE INSTALLATION:

(Refer to IB 340398 for removal and installation of new MaxPro 1000 rear squeegee)

1. Install the new MaxPro 1000 rear squeegee. (Refer to INSTRUCTION BULLETIN 340398)

SECTION 5:

FRONT SIDE BRUSH ADJUSTMENT:

(Refer to Fig. 4 and Fig. 5)

1. Drive the machine to a clean, level surface.

2. Check that the front side brush is raised. Turn the machine power off.

FOR SAFETY: Before leaving or servicing machine, stop on level surface and set parking

brake. Then turn off machine and remove key.

3. Observe the side brush from the side of the machine. The side brush should be pointing down at a 5°angle,

towards the front of the machine. Refer to Fig. 5 and Fig. 6.

4. If brush adjustment is needed, turn the machine power on. Raise the hopper and secure with the hopper

support arm. Lower the side brush.

5. Loosen side brush adjustment screw (A) if the side brush needs front/back adjustment. Tighten side brush

adjustment screw (A) after readjusting the front/back brush angle. Refer to Fig. 5 and Fig. 6.

6. Raise the side brush.

7. Observe the side brush from the front of the machine. The side brush should be pointing down at a 5°angle,

towards the outside of the machine. Refer to Fig. 5 and Fig. 6.

8. If brush adjustment is needed, lower the side brush.

9. Loosen side brush adjustment screw (B) if the side brush needs left/right adjustment. Tighten the side brush

adjustment screw (B) after readjusting the left/right brush angle. Refer to Fig. 5 and Fig. 6.

10. Raise the hopper and disengage the hopper support arm. Lower the hopper, and the side brush. Check the

side brush for proper operation.

IB 340485 (03--2010) 9

5°5°

SIDE VIEW FRONT VIEW

Front of machine

FIG. 5 -- Recommended Side Brush Angle Settings

FIG. 6 -- Side Brush Adjustment Screws

SECTION 6:

8300 ADDITIONAL DOCUMENTATION:

1. Mount the 8300 Quick Reference Guide to the machine key chain for future reference.

2. View the 8300 video (2) for recommended operating and maintenance procedures.

IB 340485 (03--2010)10

Bill Of Materials For 8300 Retrofit Kit 387548

TENNANT

Ref. Part No. Description Qty.

1 387505 Kit, conv, scrub head, disk, [MP1200] 1

2 387547 Kit, video, [8300] 1

3 86385 Sealant, silicone, [type Z5], 01.00Z 1

4 386804 Wire, 2 gauge, 32.0L BLK, 0.31 ring/0.31 ring 2

5 71529 Wire, 4 gauge, 32.0L BLK, 0.31 ring/0.31 ring 2

6 39311 Nut, hex, std, M08 X 1.25 4

7 32490 Washer, flt, 0.250 std 4

8 32988 Washer, lock, int, 0.38 4

9 41359 Nut, hex, std, M06 X 1.0 2

10 32483 Washer, flt 0.25 SAE 2

11 32982 Washer, lock, int 0.25 2

12 603103000 Fuse, 20A, 3AG, SLO--BLO 3

Bill Of Materials For Retrofit Kit, Iron Gray, CI [8300] -- 9006965

TENNANT

Ref. Part No. Description Qty.

1 9006962 Kit, conv, scrub head, disk, gray [MP1200] 1

2 387547 Kit, video, [8300] 1

3 86385 Sealant, silicone, [type Z5], 01.00Z 1

4 386804 Wire, 2 gauge, 32.0L BLK, 0.31 ring/0.31 ring 2

5 71529 Wire, 4 gauge, 32.0L BLK, 0.31 ring/0.31 ring 2

6 39311 Nut, hex, std, M08 X 1.25 4

7 32490 Washer, flt, 0.250 std 4

8 32988 Washer, lock, int, 0.38 4

9 41359 Nut, hex, std, M06 X 1.0 2

10 32483 Washer, flt 0.25 SAE 2

11 32982 Washer, lock, int 0.25 2

12 603103000 Fuse, 20A, 3AG, SLO--BLO 3

TENNANT COMPANY

P. O. Box 1452

Minneapolis, MN 55440-1452

Otros manuales para 8300

Tabla de contenidos

Otros manuales de Depurador de Tennant

Tennant

Tennant L2 Manual de usuario

Tennant

Tennant 510E Manual de capacitación

Tennant

Tennant T7 Manual de usuario

Tennant

Tennant 7200 Manual de capacitación

Tennant

Tennant Nobles SPEED SCRUB 1701 PLUS Manual del producto

Tennant

Tennant Nobles T350 Manual de usuario

Tennant

Tennant T20 LPG Manual de capacitación

Tennant

Tennant 5400 Manual de usuario

Tennant

Tennant IPC Kosmic-H PW-H31 Manual de usuario

Tennant

Tennant 5700 Manual de usuario

Tennant

Tennant 530E Manual de usuario

Tennant

Tennant T291 Manual de usuario

Tennant

Tennant T591 Manual de usuario

Tennant

Tennant Nobles WB-20B Manual del producto

Tennant

Tennant LPTE00699 Manual de usuario

Tennant

Tennant 5400 Manual del producto

Tennant

Tennant T3 Manual de usuario

Tennant

Tennant T7AMR Manual de usuario

Tennant

Tennant T16 Manual de capacitación

Tennant

Tennant T191 Manual de usuario

Tennant

Tennant LPTB03175 Manual de usuario

Tennant

Tennant 5680 Manual de usuario

Tennant

Tennant T290 Manual de usuario

Tennant

Tennant CS5 Manual de usuario

Manuales populares de Depurador de otras marcas

Olympus

Olympus M200H Manual de usuario

Clarke

Clarke BEXT 100H Manual de instalación y funcionamiento

JOHNY VAC

JOHNY VAC JVC70BCT Manual de usuario

RCm

RCm Elan Series Manual

Kärcher

Kärcher B 120 W Manual de usuario

Truvox

Truvox Orbis MotorScrubber 20 Manual de usuario

Numatic

Numatic TTB 4045/100 Manual de usuario

U.S. Products

U.S. Products PEX 500-C-TICK Instrucciones de funcionamiento

Mclennan

Mclennan C510 Manual de usuario

Columbus

Columbus ARA 66 BM 100 Manual de usuario

Numatic

Numatic TTV 678G / 300T Manual de usuario

American-Lincoln

American-Lincoln 505-945 Manual de usuario

FIORENTINI

FIORENTINI ET 65-75 Manual de usuario

Floorpul

Floorpul ruby 48 blt Guía del usuario

Onyx

Onyx RX-34 Manual de usuario

Dustbane

Dustbane Hurricane 400 Manual de usuario

Sana

Sana EUJ-702 Manual de usuario

REMS

REMS Twist Manual de usuario