Tennant 7200 Manual de capacitación

IB 340487 (6-01) LITHO IN U.S.A. 1

No. 340487

Machine: 7100,7200,7300

8200,8210,8300

Published: 6-01/00

System: SCRUBBING

INSTRUCTION BULLETIN

NOTE: DO NOT DISCARD the Parts List from the Instruction Bulletin. Place the Parts

List in the appropriate place in your machine manual for future reference.

Retaining the Parts List will make it easier to reorder individual parts and will

save you the cost of ordering an entire kit.

NOTE: Numbers in parenthesis ( ) are reference numbers for parts listed in Bill of Materials.

Installation instructions for kit number 375429, 375430 and 375431

SYNOPSIS / PROBLEM:

This kit contains the parts needed to replace the solution and recovery tank level switches

on the models 7100/7200, 8200/8210 and 7300/8300 scrubbers and sweeper/scrubbers.

Please follow step-by-step instructions.

SPECIAL TOOLS / CONSIDERATIONS: Metri--Pac wire test harness, voltmeter

(Estimated time to complete: 1 hour)

PREPARATION:

(Refer to FIG. 1 thru 7)

FOR SAFETY: Before leaving or servicing machine, stop on level surface and set parking

brake. Then turn off machine and remove key.

1. Disconnect battery cables from machine.

WARNING: Always disconnect battery cables from machine before working

on electrical components.

SOLUTION TANK PRESSURE SWITCH REPLACEMENT, 7100:

(Refer to FIG. 1)

1. Open the tank cover on the rear of the machine and locate the pressure switch 385732 and

34 inch tube 386966 on the top of the solution tank. (Refer to FIG. 1)

2. Disconnect the old pressure switch from the main wire harness.

3. Remove and discard the old pressure switch and tube from the solution tank.

NOTE: Lubricate the tube switch assemblies and hoses with a small amount of liquid soap for

easier installation.

4. Install the new tube/switch assembly 375428 in the solution tank switch opening.

(Refer to FIG. 1)

5. Connect the new tube/switch assembly 375428 to the main harness. Close the tank cover.

Check the new switch for proper operation.

IB 340487 (6-01) LITHO IN U.S.A.2

Replace 385732 and

386966 w/ 374428

FIG. 1 -- SOLUTION TANK PRESSURE SWITCH INSTALLATION, 7100

IB 340487 (6-01) LITHO IN U.S.A. 3

RECOVERY TANK PRESSURE SWITCH REPLACEMENT, 7100:

(Refer to FIG. 2)

1. Remove and set aside the tank cover, cable and mounting bolts.

2. Disconnect the vacuum fan from the main harness. Remove and set aside the vacuum fan

and mounting hardware.

3. Locate the original float switch in the recovery tank. (Refer to FIG. 2)

4. Disconnect and remove the float switch and 8 inch tube from the recovery tank.

(Refer to FIG. 2)

NOTE: Lubricate the tube/switch assemblies and hoses with a small amount of liquid soap for

easier installation.

5. Install the new 8 inch tube/switch assembly 375426 in the recovery tank switch opening.

Connect the switch to the main harness. (Refer to FIG. 2)

6. Replace and reconnect the vacuum fan to the main harness. Replace the tank cover, cable

and mounting hardware.

Replace 385744 and

385732 w/ 375426

FIG. 2 -- RECOVERY TANK PRESSURE SWITCH INSTALLATION, 7100

IB 340487 (6-01) LITHO IN U.S.A.4

RECOVERY TANK PRESSURE SWITCH REPLACEMENT, 7200:

(Refer to FIG. 3)

1. Remove and set aside the tank cover, cable and mounting bolts.

2. Disconnect the vacuum fan from the main harness. Remove and set aside the vacuum fan

and mounting hardware.

3. Locate the original float switch 385732 in the recovery tank. (Refer to FIG. 3)

4. Disconnect and remove the float switch 385732 and vacuum tube 385744 from the

recovery tank. (Refer to FIG. 3)

NOTE: Lubricate the tube/switch assemblies and hoses with a small amount of liquid soap for

easier installation.

5. Install the new 8 inch tube/switch assembly 375426 in the recovery tank switch opening.

(Refer to FIG. 3)

6. Replace and reconnect the vacuum fan to the main harness.

7. Replace the tank cover, cable and mounting hardware.

IB 340487 (6-01) LITHO IN U.S.A. 5

Replace 385732 and

385744 w/ 375426

FIG. 3 -- NEW RECOVERY TANK SWITCH INSTALLATION, 7200

IB 340487 (6-01) LITHO IN U.S.A.6

RECOVERY TANK PRESSURE SWITCH REPLACEMENT, 8200/8210:

(Refer to FIG. 4 and 5)

1. Open the engine cover, and the engine side door.

2. Remove and set aside the engine cover support bracket to access the float switches on the

recovery tank. (Refer to FIG. 1 and 2)

3. Locate the original float switches on the recovery tank. (Refer to FIG. 2)

4. Disconnect and remove the float switch 385730 and 14 inch tube 385747 from the

recovery tank. (Refer to FIG. 5)

NOTE: Lubricate tube/switch assemblies and hoses with a small amount of liquid soap for

easier installation.

5. Install the new 14 inch tube/switch assembly 375427 in the recovery tank switch opening.

(Refer to FIG. 5)

Remove engine cover

support bracket

FIG. 4 -- ENGINE COVER SUPPORT BRACKET REMOVAL, 8200/8210

SOLUTION TANK PRESSURE SWITCH REPLACEMENT, 8200/8210:

(Refer to FIG. 5)

1. Open the solution tank cover, and locate the float switch 385732.

2. Disconnect the float switch 385732 from the main harness. (Refer to FIG. 5)

3. Remove the float switch 385732 and 8 inch tube 385744 from the solution tank.

(Refer to FIG. 5)

NOTE: Lubricate tube/switch assemblies and hoses with a small amount of liquid soap for

easier installation.

4. Install the new 8 inch tube/switch assembly 375426 in the solution tank switch opening.

(Refer to FIG. 5)

5. Connect the new 8 inch tube/switch assembly 375426 to the main harness.

IB 340487 (6-01) LITHO IN U.S.A. 7

Replace 385732 and

385744 w/ 375426

Replace 385747 and

385730 w/ 375427

Solution tank

Recovery tank

FIG. 5 -- SOLUTION AND RECOVERY TANK PRESSURE SWITCH INSTALLATION,

8200/8210

IB 340487 (6-01) LITHO IN U.S.A.8

RECOVERY TANK PRESSURE SWITCH REPLACEMENT, 7300/8300:

(Refer to FIG. 6)

1. Open the recovery tank cover, and locate the float switch 385732 and 8 inch tube 375744.

2. Disconnect and remove the float switch 385732 and 8 inch tube 385744 from the recovery

tank. (Refer to FIG. 6)

NOTE: Lubricate tube/switch assemblies and hoses with a small amount of liquid soap for

easier installation.

3. Install the new 8 inch tube/switch assembly 375426 in the recovery switch opening.

Connect the new switch to the main wire harness. (Refer to FIG. 6)

4. Close the recovery tank cover.

NOTE: TO CONFIRM PROPER PRESSURE SWITCH OPERATION, PERFORM THE

FOLLOWING:

1. Remove the switch from the tank to be tested. Solution tank has 8 inch tube/switch

assembly. Recovery tank has 14 inch tube/switch assembly.

For 8 inch tube/switch assembly -- Measure and place a mark at 4 inches from the bottom

of the tube.

For 14 inch tube/switch assembly -- Measure and place marks at 4 and 10 inches from the

bottom of the tube.

2. Connect the switch to an ohmmeter with the metri--pac test wire harness (375023), or use

clips to directly clamp on to the switch harness. The ohmmeter should read O.L. before

switch is activated.

3. Slowly lower the switch into a 5 gallon bucket of water filled with roughly twelve inches of

water. The switch should read below 1 ohm when activated at the 4 or 10 inch level.

4. Hold the tube at the 4 in or 10 in level for 30 seconds. If there are no leaks in the

tube/switch assembly, the ohm reading will hold steady. If a leak is present, or if the switch

is malfunctioning, the ohm reading will show O.L. (open loop).

IB 340487 (6-01) LITHO IN U.S.A. 9

Replace 385732 and

385744 w/ 375426

FIG. 6 -- SOLUTION TANK PRESSURE SWITCH INSTALLATION, 7300/8300

IB 340487 (6-01) LITHO IN U.S.A.10

SOLUTION TANK PRESSURE SWITCH REPLACEMENT, 7300/8300:

(Refer to FIG. 7)

1. Open the solution tank cover, and locate the float switch 385732 and 34 inch tube 386966.

2. Disconnect and remove the float switch 385732 and 34 inch tube 386966 from the

recovery tank. (Refer to FIG. 7)

NOTE: Lubricate tube/switch assemblies and hoses with a small amount of liquid soap for

easier installation.

3. Install the new 34 inch tube/switch assembly 375428 in the solution tank switch opening.

Connect the new switch to the main wire harness. (Refer to FIG. 6)

4. Notice that the tube/ switch assembly has HIGH and LOW pressure settings.

(Refer to FIG. 6)

5. Close the recovery tank cover. Check the new 34 inch tube/switch assembly 375428 for

proper operation .

Replace 385732 and 386966

w/ 375428

FIG. 7 -- RECOVERY TANK PRESSURE SWITCH INSTALLATION, 7300/8300

Otros manuales para 7200

Este manual sirve para los siguientes modelos

Otros manuales de Depurador de Tennant

Tennant

Tennant T7 Manual de usuario

Tennant

Tennant 7300 Manual de capacitación

Tennant

Tennant T291 Manual de usuario

Tennant

Tennant 800D Manual de usuario

Tennant

Tennant T12 Manual de capacitación

Tennant

Tennant 8400 Manual de usuario

Tennant

Tennant 7200 Manual de capacitación

Tennant

Tennant T191 Manual de usuario

Tennant

Tennant IPC Kosmic-H PW-H31 Manual de usuario

Tennant

Tennant 7200 Manual de usuario

Tennant

Tennant T290 Manual de usuario

Tennant

Tennant 8410 Manual de usuario

Tennant

Tennant CS16 Manual de usuario

Tennant

Tennant CS16 Manual de usuario

Tennant

Tennant 510E Manual de capacitación

Tennant

Tennant 7300 Manual de usuario

Tennant

Tennant T600e Instrucciones de funcionamiento e instalación

Tennant

Tennant T5 Manual de usuario

Tennant

Tennant M17 Series Manual de capacitación

Tennant

Tennant 7400 Manual de usuario

Tennant

Tennant T3 Manual de usuario

Tennant

Tennant T600e Manual de usuario

Tennant

Tennant 5700 Manual de usuario

Tennant

Tennant 5100 Manual del producto

Manuales populares de Depurador de otras marcas

Olympus

Olympus M200H Manual de usuario

Clarke

Clarke BEXT 100H Manual de instalación y funcionamiento

JOHNY VAC

JOHNY VAC JVC70BCT Manual de usuario

RCm

RCm Elan Series Manual

Kärcher

Kärcher B 120 W Manual de usuario

Truvox

Truvox Orbis MotorScrubber 20 Manual de usuario

Numatic

Numatic TTB 4045/100 Manual de usuario

U.S. Products

U.S. Products PEX 500-C-TICK Instrucciones de funcionamiento

Mclennan

Mclennan C510 Manual de usuario

Columbus

Columbus ARA 66 BM 100 Manual de usuario

Numatic

Numatic TTV 678G / 300T Manual de usuario

American-Lincoln

American-Lincoln 505-945 Manual de usuario

FIORENTINI

FIORENTINI ET 65-75 Manual de usuario

Floorpul

Floorpul ruby 48 blt Guía del usuario

Onyx

Onyx RX-34 Manual de usuario

Dustbane

Dustbane Hurricane 400 Manual de usuario

Sana

Sana EUJ-702 Manual de usuario

REMS

REMS Twist Manual de usuario