TELink 1250i Manual de usuario

SYSTEM OVERVIEW

Front Panel

The Status LED, Volume adjustments, and BGM adjustments are located on the

front panel.

Figure 1 - Front Panel Diagram

Status LED – Lights to indicate the current operation status of the unit.

Volume Adjustments – Used to control the Volume locally, if permitted to do

so by your dealer. Also used in Connect On Demand situations (see

page 10).

BGM Adjustment – Used to control the BGM Volume locally, if permitted to

do so by your dealer.

TELink 1250i 6 8/17/2004

Connections Panel

The back side panel is where the connectors are for external equipment

including the Power Supply, Ethernet jack, and the external audio system that

receives the TELink®1250i 's output. Also located here are the Impedance

Switch and the Power Switch.

Figure 2 - Side Panel Diagram

Ethernet Jack – Used to connect to your Local Area Network (LAN).

BGM Input – Used to connect to an external BGM source.

Audio Output – Select one of the following Impedances with the Impedance

Switch.

8ΩAudio Output – Used to connect an external 8 Ohm speaker or

headphones.

1KΩAudio Output – Used to connect to an external audio system such

as a KSU/PBX Phone System or an amplifier.

Power Switch – Used to turn the unit Off/On.

Power Supply – Used to supply power to the unit.

TELink 1250i 7 8/17/2004

INSTALLATION

Step 1 – Connections

Locate the TELink®1250i within 6 feet of an 110VAC outlet. The unit is designed

to be placed on a flat, level surface or securely mounted on a wall. Be sure to

leave clearance for connections and adjustments.

Important: Devices that emit strong electromagnetic fields such as computer

monitors and fluorescent lights may interfere with message loading, so locate

the unit at least a few feet away from such devices.

To help protect against power surges and other electrical problems, the use of a

quality surge suppressor strip (which is different from a standard multi-outlet

power strip) is strongly recommended. Damage caused by power surges,

lightning, or other electrical problems are not covered under warranty.

Figure 3 - Installation Diagram

TELink 1250i 8 8/17/2004

Connection Instructions

1. Turn the power switch OFF. Plug the included power supply into a normal

110VAC wall outlet, and the opposite end into the TELink®1250i. Only use

the power pack provided with the unit (12VDC, center pin positive). Many

power supplies look alike, but provide different output. Using the wrong one

voids your warranty and may damage the unit.

2. Connect the audio output jack to the external audio system input using a

mono RCA-to-RCA cable (included). If the external audio system does not

have an RCA-style input, use the included RCA to 1/8 inch adapter. Be sure

to select the right impedance before turning the unit on.

3. NOT REQUIRED FOR OMNI-Connect the BGM using a mono RCA-to-RCA

cable (included). If the BGM source does not have an RCA-style output, use

the included RCA to 1/8 inch adapter. This step is optional and only required

if you are using Background Music.

4. Connect the Ethernet jack to your Local Area Network. (LAN) The unit is

factory DHCP enabled and should obtain an IP address automatically. See

the local Network Administrator or the Quick Install Guide on the back page of

this manual for assistance.

5. Turn the unit on.

6. Call Omni to confirm connectivity between the unit and their server(s)

via the Internet.

Step 2 – Adjust Volume

The Volume buttons on the front of the unit are used to adjust the Volume to a

comfortable listening level.

TELink 1250i 9 8/17/2004

PLAYBACK OPERATION

Continuous Play

The TELink®1250i plays back all dealer-loaded music and messages over your

sound system or MOH port continuously. The unit automatically checks your

dealer’s server(s) on a routine basis for new music and messages as they

become available.

Volume Adjustments

If permitted by your dealer, the Volume may be adjusted using the Volume

buttons on the front of the unit.

Connect On Demand

Connect On Demand allows you to force an instant connection to your dealer’s

server(s) to check for new music and messages outside of its routine Connect-

Back cycle. To perform a Connect On Demand, turn the power to the unit on

while depressing the Volume down (middle) button. Release the button once

the Status LED turns Orange.

Status LED Indications

Indication Meaning

Solid Red Unit has no messages.

Solid Green Unit has messages loaded and is playing audio.

Solid Orange Unit is currently connected to dealer’s server and is

downloading new music and messages.

Blinking Orange Unit is establishing/disconnecting a connection to the

dealer’s server.

Table 1 – Status LED Indications

TELink 1250i 10 8/17/2004

WALL MOUNTING INSTRUCTIONS

Using the included wall mount bracket and two screws, secure the unit onto the wall

where you wish to mount it.

Consider the weight of the TELink®1250i when choosing a mounting wall. Make

sure the wall’s construction is sufficiently strong to support the weight of the unit

securely. Make sure both screws are driven into sturdy supports.

When mounting the unit, be sure that the front panel and Status LED is clearly

visible for you to see.

FLAT SURFACE INSTRUCTIONS

Place the unit on a sturdy table, away from any obstructions that may disrupt it.

The unit may be placed in any direction, however, be sure that the front panel and

Status LED is clearly visible for you to see.

TELink 1250i 11 8/17/2004

TELink 1250i 16 8/17/2004

INSTALLER/CUSTOMER QUICK INSTALL GUIDE

Step 1 : Unpack the contents of the TELink®1250i package - You should have the following

items:

- TELink®1250i

- Installer Utilities CD

- Power pack

- Network cable

- RCA to RCA cord

- RCA to 1/8” adapter

- Wall mount kit

- Manual and/or Quick Install Guide

Step 2: Connect the TELink®1250i to power using the supplied power pack.

Step 3: Connect the TELink®1250i to your network using the supplied network cable.

Step 4: Turn the unit ON.

Step 5: The TELink®1250i has been factory-set for DHCP and should obtain an IP address

automatically.

Step 6: Turn the unit OFF.

Step 7: Wait 5 seconds.

Step 8: Turn the unit ON while pressing the VOLUME DOWN button.

Step 9: Release the button when the status LED turns ORANGE.

Step 10: Call your dealer to confirm that the unit has made a connection* to their server.

Step 11: Connect the RCA output to your music-on-hold port or PA system.

Step 12: Verify the status LED is green and audio is playing to your MOH port or your PA

speakers.

* You can also verify connection to the dealers/service provider’s server by using the

“Connection Tester” application that is included on the Installer Utilities CD.

IF YOU NEED TO SET A STATIC IP ADDRESS PLEASE READ BELOW

If you do not have a DHCP server, you will need to manually assign IP information to the

TELink®1250i using the Configuration Utility on the Installer Utilities CD.

Replace Step 5 above with the following:

Step 5a - Place the Installer Utilities CD on a computer on the local network.

Step 5b - Select the Configuator Utility from the pop-up menu.

Step 5c - The utility will automatically search the network and find the TELink®1250i.

Step 5d - You can now assign it an available static IP address.

Step 5d - If the utility can not find the TELink®1250i, click MANUAL ENTRY and enter the MAC

address and IP information. The MAC address label can be found on the bottom of

the unit.

Step 5e - Press EXIT and continue with installation.

INSTALLATION OF THIS PRODUCT SHOULD BE DONE BY A QUALIFIED INSTALLER!

PLEASE CALL YOUR DEALER FOR SUPPORT ON THIS PRODUCT!

Tabla de contenidos

Manuales populares de Sistema estéreo de otras marcas

LG CM3330B Manual de usuario

Sony

Sony SS-CEP50 Manual de usuario

Cetacea Sound

Cetacea Sound CVS-II Manual de usuario

Aiwa

Aiwa XR-H66MD Manual de usuario

Denon

Denon UCD-250 Manual de usuario

Sanyo

Sanyo DC-MX41i Manual de usuario

Sharp

Sharp CD-ES600V Manual de usuario

Exibel

Exibel BDX600-UK Manual de usuario

Sanyo

Sanyo DC-F320 Manual de usuario

Philips

Philips FWM583X Manual de usuario

Sharp

Sharp CD-C462 Manual de usuario

Onkyo

Onkyo CBX 300 - CD / MP3 Clock Radio Manual de usuario

Aiwa

Aiwa XR-EM70 Manual de usuario

Cyrus

Cyrus Lyric Manual de usuario

Philips

Philips MCM159/98 Manual de usuario

Philips/Magnavox

Philips/Magnavox Magnavox FW 62C Manual de usuario

RCA

RCA RS3965SB Manual de usuario

Sharp

Sharp XL-UH240 Manual de usuario