Telguard TG-SCI Plus Manual de usuario
P/N 56048603
INSIDE VIEW
DC In
GND
Trip In
STC
STC
LED 4
LED 3
LED 2
LED 1
CONFIG RSSI
RJ-45
QUICK INSTALL GUIDE
Register for Telguard Service
Register online at www.telguard.com
Connect Dialer and Power to the TG-SCI Plus
Connect the alarm panel’s dialer to the RJ-45 jack on the
TGSCIPG01. If using the Single Line Interface Cable (SLIC) for
power, connect the RJ-45 cable’s orange wire to the alarm
panel’s ground and its blue wire to the panel’s auxiliary power. If
using the terminal block, connect the terminals closest to the RJ
jack (labeled GND and DC IN) to the panel’s ground and power,
respectively.
Measure RSSI and Activate
Apply power and press the RSSI button to put the LEDs
into RSSI display mode. When you find a location that provides
2 ½ bars or more (LEDs 4, 3 solid ON and 2 flashing), you are
ready to activate. Press the RSSI button again to return the
LEDs to normal display mode, and trigger and alarm from the
panel. The first alarm will activate the unit with the TCC and will
not be sent to the central station. When activation is successful,
LED 1 will turn solid green.
Finish Installation
Send more signals and confirm delivery with central
station. Use the provided hardware to mount the device.
1
2
3
4
TG-SCI Plus
P/N 56048603
Button Descriptions (Accessible when cover is off)
Button
Functions
CONFIG
•Press & release to trigger WPS Push-Button
association.
•Press & hold for 5 seconds then release to enable
the Wi-Fi Configuration AP.
•Press & hold for 15 seconds then release to
restore Factory Defaults.
RSSI
•Press & release to switch between normal mode
and RSSI mode.
•Press & hold for 5 seconds then release to send a
test message to the TCC.
Single Line Interface Cable (S.L.I.C.)
Unused
GND (2, orange)
ST C(3, black)
Ring (4, red)
Unused
DC +(7, blue)
STC (6, ye llow)
Tip (5, green)
LED Indicators (Normal Display)
Indicator
Description
LED 1
Telguard Registration & Activation
LED 2
Cellular Status
LED 3
Wi-Fi Status
LED 4
Not Used (Used only in RSSI Mode)
LED Indicators (RSSI Display)
RSSI
Value
Illuminated LEDs
RF (dBm)
NO SVC
LED 4 = slow flashing Red
LED 3-1 = off
n/a
1
LED 4 = solid Amber
LED 3-1 = off
≤ -111
1½
LED 4 = solid Amber
LED 3 = slow flashing Amber
LED 2-1 = off
-110
2
LED 4-3 = solid Amber
LED 2-1 = off
-100
2½
LED 4-3 = solid Green
LED 2 = slow flashing Green
LED 2 = off
-90 (Minimum
signal strength
required)
3
LED 4-2 = solid Green
LED 1 = off
-80
3½
LED 4-2 = solid Green
LED 1 = slow flashing Green
-70
4
LED 4-1 = solid Green
-60
For more detailed installation descriptions, please refer to the
Telguard Installation and Operating Instructions available for
download at www.Telguard.com
Este manual sirve para los siguientes modelos
1
Otros manuales de Teléfono móvil de Telguard
Telguard
Telguard TG-1 Express CDMA Manual de usuario
Telguard
Telguard Dual Path Series Guía de solución de problemas
Telguard
Telguard TG-1 Express CDMA Manual de usuario
Telguard
Telguard TG-7 Series Guía de solución de problemas
Telguard
Telguard TG-4 Manual de usuario
Telguard
Telguard TG-1 Express CDMA Manual de usuario
Telguard
Telguard TG-1 Express CDMA Manual de usuario
Telguard
Telguard TG-7 Series Manual de usuario
Telguard
Telguard TG-1 Express CDMA Manual de usuario
Telguard
Telguard TG-4 Manual de usuario
