Teleste EASI IND101 Manual de usuario
EASITM ATM Series
User Manual
IND1x1 MPEG-2 Decoder
IND1x1 User Manual, 59300037, rev001
IND1x1 Series User Manual rev001
Introduction..............................................................................................................1
General.........................................................................................................................................1
Features .......................................................................................................................................1
Monitoring Functions....................................................................................................................1
Models..........................................................................................................................................1
Installation................................................................................................................2
Quick Instructions.........................................................................................................................2
Mechanical Installation.................................................................................................................3
Mechanical Connections ..............................................................................................................3
Front Panel Leds ..........................................................................................................................3
Connections .............................................................................................................4
General.........................................................................................................................................4
S-Video Connection .....................................................................................................................4
ATM Connection ...........................................................................................................................4
How to Configure the IND1x1 MPEG-2 Decoder ...................................................5
General.........................................................................................................................................5
System Requirements..................................................................................................................5
Hardware Requirements .............................................................................................................5
Software Requirements...............................................................................................................5
The Commander and Viewer Softwares.......................................................................................5
Establishing a Data Connection ...................................................................................................6
Starting CATVisorTM Commander .................................................................................................7
CATVisorTM Commander - Connected Window ............................................................................8
Configuring the Units using CATVisorTM Commander ..................................................................9
IND1x1 MPEG-2 Decoder Configuration Display v1.0 ........................................10
General..................................................................................................................................10-11
Status Page...........................................................................................................................12-13
Properties Page..........................................................................................................................14
ATM Page..............................................................................................................................15-16
Data Page ..................................................................................................................................17
PID Page ....................................................................................................................................18
Video Page ............................................................................................................................19-20
In-Band Management Page ..................................................................................................21-22
SNMP Page................................................................................................................................23
Constructing EASITM Networks.............................................................................24
Concatenating Encoders and Decoders.....................................................................................24
Data Broadcasting......................................................................................................................24
Copyright Acknowledgements .............................................................................24
Trademark Acknowledgements ............................................................................24
Contents
General
IND1x1 is a rack mount one channel video Decoder unit for
EASITM surveillance applications (see list of models below).
This unit provides a transparent link of PAL or NTSC video
signal. Transmission is accomplished over an ATM network.
IND1x1 Decoder makes up a pair e.g. with INE1x2 or INE2x2
MPEG Encoder. The transmission is accomplished over ATM
network utilizing AAL5 cell structure.
Features
- Selectable CVBS and Y/C video outputs
- GOP structure selectable
- Bit rate scalable up to 18 Mbps
- Frame rate 25 (PAL), 30 (NTSC)
- VP/VC mapping
- Compatibility with DVX-system
- ATM inband control channel
Monitoring Functions
- Video input synchronisation
- ATM frame synchronisation
- Input stream rate
- Output stream rate
Models (Rack mount Cards)
IND101 STM-1/OC-3 Interface CAT5 (100 m)
IND121 STM-1/OC-3 Interface Multimode (2 km)
IND131 STM-1/OC-3 Interface Singlemode Short Haul (15 km)
IND141 STM-1/OC-3 Interface Singlemode Medium Haul (45 km)
INTRODUCTION
IND1x1 Rack Mount CAT5, Multimode or Singlemode
Decoder Unit with one Video, In-Band Management
IND1x1 Series User Manual rev001 1
INSTALLATION
Quick Instructions
Install the unit into a DVX002-installation frame
equipped with a DVP power supply.
The rack must have a unique bus address assigned.
Switch on the system power and see that the “M”, “C”
and “V” -indicators on the front panel of the unit are lit.
The “M” (=module) should lit green to show that
hardware is operating probely.
Connect a monitor to either CVBS video output (BNC)
or S-VIDEO output (mini-DIN). These signals are both
constantly available.
Connect the ATM network to port “ATM” in the
front panel.
Connect a PC (with the Commander software installed)
to the Control Bus using the DVX021 connection cable.
Start Commander and select the unit to configure and
proceed by filling in the required parameters.
Alternatively, if the in-band management is operational
over the ATM network, this can be done remotely from a
control center.
Make sure that the unit is not indicating any alarms or
warnings (Status page). The “M”, “C” and “V” -indicators
on the front panel should now lit green.
1
2
3
4
5
6
7
2 IND1x1 Series User Manual rev001
Mechanical Installation
IND1x1 is installed into a DVX002 installation frame equipped
with a specified DVX bus address (refer to the frame
installation instructions) and a DVP412 (115 V AC) or a
DVP432 (230 V AC) power supply.
The unit can be installed into any frame position, however the
power supply is normally placed in the left-hand side of the
frame. Lock the unit into place using the locking screws on the
front panel (see picture 1).
Note! See that the “M” (module) -indicator lits green. If the
indicator lits red, the unit in question has a module error and is
giving an alarm. See the “Status page” for more information.
Mechanical Connections
1. Locking screw.
2. Composite video output (BNC male).
3. S-video (Y/C) output (4 pin min-DIN female).
4. STM-1/OC-3 interface, depending on model in
question, either RJ-45 female (when CAT5) or dual-
SC/PC (when optical).
5. Led indicators, see section below.
6. Handle.
Front Panel Leds
When the unit is working properly, the “M” led on the front
panel is green. If the unit senses a module error, the “M” led is
red. Blinking green “M” led indicates that Commander software
is communicating with the unit in question.
When the ATM connection status is OK, the “C” led on the front
panel is green. If the ATM signal is missing or it’s level is too
low, the “C” led is yellow.
When the Video connection status is OK, the “V” led on the
front panel is green. If the video signal is missing or it’s level is
too low, the “V” led is yellow.
Picture 1.
IND101 Mpeg-2 Decoder /
connections.
MPEG
DECODER
IND101
VIDEO
M VC
S-VIDEO
ATM
1
2
3
4
5
6
IND1x1 Series User Manual rev001 3
43
12
Picture 2.
S-video connector
(4 pin min-DIN female).
Pin 1 - Ground (Y)
Pin 2 - Ground (C)
Pin 3 - Luminance (Y)
Pin 4 - Chrominance (C)
CONNECTIONS
General
All products in EASITM family have the same connection scheme
in their connectors. Depending the model in question, there is
video, S-video, audio, data, 10Base-T, ATM and control bus
(DVX bus) connection in the unit.
Video Connection
The video (input) connector in use is either a BNC male
(composite) or a 4 pin min-DIN female (S-video) connector (see
picture 2 and section “Video Page” for detailed description).
ATM Connection
The ATM connector in use is either a RJ-45 female connector
(when CAT5 connection) or dual SC/PC connector (when optical
connection). See picture 3 and section “ATM Page” for detailed
description
Optical ATM connection meets class 1 laser safety requirements
of IEC 825-2: 1993 and US department of health services 21
CFR 1040.10 and 1040.11 (1990) when operated within the
specified temperature, power supply and duty cycle ranges.
18
ATM
Pin 2 - Tx (-)
Pin 7 - Rx (+)
Pin 8 - Rx (-)
Pin 1 - Tx (+)
18
Picture 3.
ATM connection (CAT5).
4 IND1x1 Series User Manual rev001
General
This chapter tells how with help of the Commander software
you can configure the settings of IND1x1 Decoder and
introduce the functions of the Configuration Displays. The
Configuration Displays are a part of the Commander software
application.
System Requirements
Hardware requirements
- The PC, minimum requirements: Pentium II prosessor, display
capable to 256 colors and 1024x768 resolution, CD-ROM
drive, 128 MB RAM, Windows 98/Me/NT4.0 (SP 4 upgrade)
/2000 (SP 2 upgrade) /XP.
- DVX021 connection cable between the PC and IND1x1 unit.
Software requirements
- DCS110 Commander software (includes also the
Viewer software).
- DUS100 Viewer Software (the Viewer software
upgrade version). The Viewer Software is a package of DLL
files for EASITM products.
The Commander and Viewer softwares
The IND1x1 Decoders are fully controllable with the
Commander Software. The Commander installation package is
supplied on DCS110 CD-ROM. This CD-ROM contains also the
Viewer software.
DUS100 CD-ROM contains only the Viewer
Software. This CD-ROM is meant for Viewer software upgrade
without need to re-install Commander software.
HOW TO CONFIGURE THE IND1x1
MPEG-2 DECODER
IND1x1 Series User Manual rev001 5
Establishing a Data Connection
1. Connect a DVX021 connection cable between the COM
port of your PC and the Control Bus connector of the
IND1x1 unit.
2. Install the Commander and Viewer softwares by running
autorun.exe (if installation doesn’t start automatically). The
following window appears on the screen (picture 4).
Follow the instructions given during the installation process.
Picture 4.
Commander’s installation setup view (Commander version 2.2).
6 IND1x1 Series User Manual rev001
Starting CATVisorTM Commander
After installing the softwares launch Commander. When the
program has started the following “Untitled Commander”
window appears on the screen (picture 6).
Picture 6.
Commander’s main view.
Commander is now running, but not yet communicating with
IND1x1. Create the connection to the IND1x1 by choosing -->
File/New or Connection/Add New commands from the pull-
down menus. The following “Add New Connection” window
appears on the screen (see picture 5).
Make the following settings (these are the default settings):
Type: Serial Port
Serial Port Name: COM1 (choose COM port where the
DVX021 cable is connected, e.g. COM1 port)
Busmode: DVX Bus
Click to continue.
Communication between Commander and IND1x1 is
now created.
Note! You can also re-opened the saved connection by
choosing --> File/Open command from the pull-down menus.
When making a new connection for the first time, you may refer
to the Commander’s User Manual for the correct settings.
Picture 5.
Commander’s “Add New
Connection” view.
IND1x1 Series User Manual rev001 7
CATVisorTM Commander - Connected Window
Picture 7.
Commander Main View, connected window.
The Commander main view consist of the Element Tree
Window, Element Window, Event Window, Pull Down
Menus, the Tool Bar and the Status Bar.
The Commander main view window is divided into three main
sections: Element Tree Window, Element Window and Event
Window (see picture 7).
When a connection is created, the connected unit found
appears in the Commander’s Element Tree Window / Element
Tree Directory and it is also listed in the Event Window.
The Event Window displays all detected events in connection.
The Element Window displays more detailed information on
an individual unit selected in the Element Tree Window.
Pull-Down menus Toolbar
Event Window
Element Tree Window
Element Window
Status Bar
Element Tree Directory
8 IND1x1 Series User Manual rev001
Este manual sirve para los siguientes modelos
3
Tabla de contenidos
