Telemark PROGRAMMABLE SWEEP Manual de usuario
PROGRAMMABLE SWEEP
INSTRUCTION MANUAL
Copyright ©TELEMARK, 1995-2020 –All rights reserved
Manual Rev 1.0.0 June 2020
telemark.com
This manual is for software version 1.11.20159 and above.
Current interface and software options might be different. Contact manufacturer for current manual
release if the software interface or functions are different from this manual or download the current
version of this manual at
https://telemark.com/e-beam-power-supplies/sweep-controllers/
Brand and product names are trademarks or registered trademarks of their respective companies
Programmable Sweep Instruction Manual
telemark.com 2 of 58 Rev 1.0.0
TABLE OF CONTENTS
1INTRODUCTION..........................................................................7
1.1 Intended Use.........................................................................................7
1.2 Liabilities and Warranty .........................................................................7
1.3 Safety....................................................................................................8
1.3.1 Personnel Qualifications ........................................................................................ 8
1.3.2 Illustration of Residual Dangers ............................................................................. 8
1.4 General Safety Instructions ...................................................................9
2TECHNICAL DATA....................................................................11
2.1 General Data.......................................................................................11
2.1.1 Mechanical Data .................................................................................................. 11
2.1.2 Ambience ............................................................................................................. 12
2.1.3 Use and Operating Modes ................................................................................... 12
2.1.4 Standards............................................................................................................. 12
2.2 Mains Connection ...............................................................................13
2.3 Pack List..............................................................................................13
2.4 Specifications ......................................................................................14
2.5 Features..............................................................................................15
2.6 Interfaces ............................................................................................15
2.6.1 Input/Output Interface .......................................................................................... 15
3INSTALLATION .........................................................................16
3.1 Unpacking ...........................................................................................16
3.2 Mechanical Installation........................................................................16
3.2.1 Required components .......................................................................................... 17
3.3 Installation ...........................................................................................17
3.3.1 Rack Installation................................................................................................... 17
3.4 Controller Connecting .........................................................................18
3.4.1 Front Panel........................................................................................................... 18
3.4.2 Rear Panel ........................................................................................................... 19
3.4.3 Mains Connection ................................................................................................ 20
3.4.4 Grounding ............................................................................................................ 20
Programmable Sweep Instruction Manual
telemark.com 3 of 58 Rev 1.0.0
3.4.5 Remote Control - J2............................................................................................. 22
3.4.6 Host –J1 .............................................................................................................. 23
3.4.7 Output - J3 ........................................................................................................... 23
3.5 List of Accessories or Supplies ...........................................................25
4USING THE PROGRAMMABLE SWEEP..................................26
4.1 Front Panel..........................................................................................26
4.1.1 Main Power Switch............................................................................................... 26
4.1.2 Power On LED indicator ...................................................................................... 27
4.1.3 Handheld.............................................................................................................. 27
4.1.4 LCD Touchscreen ................................................................................................ 27
4.2 Avatar Handheld .................................................................................27
4.2.1 Four-way and OK Momentary switch................................................................... 28
4.2.2 Joystick ................................................................................................................ 29
5CONFIGURATION .....................................................................30
5.1 Unlocking ............................................................................................30
5.2 Configure System................................................................................31
5.2.1 Screen Saver ....................................................................................................... 31
5.2.2 Input ..................................................................................................................... 31
5.2.3 Beam in Pocket (BIP)........................................................................................... 32
5.2.4 Angle Offset ......................................................................................................... 33
5.2.5 Lat/Long Flip ........................................................................................................ 33
5.2.6 Factory Service .................................................................................................... 33
5.3 Pattern Pocket Setup ..........................................................................34
5.4 Copy Pocket Setup .............................................................................35
5.5 Configure Pattern ................................................................................36
5.6 Display Tail Length..............................................................................37
5.7 Profile..................................................................................................37
5.8 Pattern Configuration Setup ................................................................39
5.8.1 Triangle ................................................................................................................ 39
5.8.2 Sine ...................................................................................................................... 40
5.8.3 Figure 8 ................................................................................................................ 41
5.8.4 Line ...................................................................................................................... 42
5.8.5 Circle .................................................................................................................... 42
5.8.6 Spiral .................................................................................................................... 43
5.8.7 Point ..................................................................................................................... 43
5.8.8 Programmable Shape .......................................................................................... 44
Programmable Sweep Instruction Manual
telemark.com 4 of 58 Rev 1.0.0
5.9 Making Programmable Shapes ...........................................................44
5.9.1 Constant Velocity/Constant Dwell........................................................................ 46
6OPERATION..............................................................................48
6.1 General Operation...............................................................................48
6.1.1 Power-Up ............................................................................................................. 48
6.1.2 Power-Down......................................................................................................... 48
6.2 Pattern Selection.................................................................................49
6.3 Move Pattern.......................................................................................49
6.4 Run On/Off ..........................................................................................50
6.5 Remote On/Off ....................................................................................51
7MAINTENANCE AND SERVICE................................................53
7.1 Maintenance........................................................................................53
7.2 Cleaning..............................................................................................53
8STORAGE AND DISPOSAL......................................................54
8.1 Packaging ...........................................................................................54
8.2 Storage................................................................................................54
8.3 Disposal ..............................................................................................54
8.4 WEEE .................................................................................................54
9ERRORS AND WARNINGS ......................................................56
9.1 Error Codes.........................................................................................56
9.2 Interlock Fail........................................................................................57
10 WARRANTY CONDITIONS .......................................................58
10.1 Limited Warranty .................................................................................58
Programmable Sweep Instruction Manual
telemark.com 5 of 58 Rev 1.0.0
TABLE OF FIGURES
Figure 1-1, Keep Foreign Material Out of the Programmable Sweep.............................. 9
Figure 2-1, Sweep Reference Dimensions.................................................................... 11
Figure 3-1, Front Panel Connection .............................................................................. 18
Figure 3-2, Avatar Sweep Handheld ............................................................................. 19
Figure 3-3, Rear panel Programmable Sweep Controller.............................................. 19
Figure 3-4, Three-conductor cable with protective ground (example) ........................... 20
Figure 3-5, Connections ................................................................................................ 21
Figure 3-6, Dsub25 pinouts ........................................................................................... 22
Figure 3-7, Host Port..................................................................................................... 23
Figure 3-8, Telemark standard Coil Wire Reference Code............................................ 23
Figure 3-9, Telemark Source Standard Direction Reference......................................... 24
Figure 3-10, Typical 8 pin Sweep/coil Installation ......................................................... 24
Figure 3-11, Typical 4 Pin Sweep/coil Installation ......................................................... 24
Figure 4-1 - Front Panel ................................................................................................ 26
Figure 4-2, Avatar Sweep Handheld ............................................................................. 27
Figure 4-3, Four way and OK switch Operation ............................................................ 28
Figure 5-1, Unlocking Screen........................................................................................ 30
Figure 5-2, Configure System ....................................................................................... 31
Figure 5-3, Beam in Pocket Setup ................................................................................ 32
Figure 5-4, Angle Offset Setup...................................................................................... 33
Figure 5-5, Lat/Long Flip Setup..................................................................................... 33
Figure 5-6, Select Pattern ............................................................................................. 34
Figure 5-7, Select Pattern Pocket Setup ....................................................................... 34
Figure 5-8, Setting the Pocket Center ........................................................................... 34
Figure 5-9, Setting Pocket Limits .................................................................................. 35
Figure 5-10, Copy Pocket Setup ................................................................................... 35
Figure 5-11, Select Configure Pattern........................................................................... 36
Figure 5-12, Select Shape............................................................................................. 36
Programmable Sweep Instruction Manual
telemark.com 6 of 58 Rev 1.0.0
Figure 5-13, Select Shift Menu...................................................................................... 36
Figure 5-14, Positive Profile Representations ............................................................... 38
Figure 5-15, Setup Pattern, Triangle ............................................................................. 39
Figure 5-16, Setup Pattern, Sine................................................................................... 40
Figure 5-17, Setup Pattern, Figure 8............................................................................. 41
Figure 5-18, Setup Pattern, Line ................................................................................... 42
Figure 5-19, Setup Pattern, Circle................................................................................. 42
Figure 5-20, Setup Pattern, Spiral................................................................................. 43
Figure 5-21, Setup Pattern, Point.................................................................................. 43
Figure 5-22, Select Shape............................................................................................. 44
Figure 5-23, Setup Pattern ............................................................................................ 44
Figure 5-24, Programmable Shape Select .................................................................... 45
Figure 5-25, Shape Configure ....................................................................................... 45
Figure 5-26, Shape Edit ................................................................................................ 46
Figure 5-27, Constant Velocity Shown on Oscilloscope ................................................ 46
Figure 5-28, Constant Dwell Shown on Oscilloscope.................................................... 47
Figure 6-1, Touchscreen Display .................................................................................. 48
Figure 6-2, Pattern Selection......................................................................................... 49
Figure 6-3, Pattern Shift ................................................................................................ 49
Figure 6-4, Move Pattern, Joystick connected .............................................................. 49
Figure 6-5, Move Pattern, Joystick not Connected........................................................ 50
Figure 6-6, Run On/Off.................................................................................................. 50
Figure 6-7, Run Off, Joystick......................................................................................... 51
Figure 6-8, Remote, No Pattern .................................................................................... 52
Figure 6-9, Remote, Pattern Selected ........................................................................... 52
Figure 8-1, WEEE Symbol ............................................................................................ 55
Figure 9-1, Interlock Fail................................................................................................ 57
Programmable Sweep Instruction Manual INTRODUCTION
telemark.com 7 of 58 Rev 1.0.0
1 INTRODUCTION
Please read this manual carefully to ensure optimum operating conditions right from
the start. This user manual handbook contains important information about the
functionality, installation, start-up and operation of the Model Programmable Sweep.
1.1 Intended Use
The Telemark Programmable Sweep is intended for use with electron beam (EB)
sources such as the Telemark line of EB sources and with other compatible EB
sources that use electromagnetic deflection or combinations of electromagnetic
deflection and permanent magnet focusing. The sweep output drives the latitude and
longitude (X, Y) coils of an electron beam source to move the beam spot.
The device is referred to as Programmable Sweep in the remainder of this manual.
1.2 Liabilities and Warranty
Telemark is not liable for damages resulting from improper use of the device and the
guarantee expires, if the user, or third party:
•ignores information contained in this manual,
•utilizes the product in a manner inconsistent with intended purpose,
•makes any modification or alteration of the product,
•unit should not be used with unauthorized accessories (compatible accessories,
types and models can be found in the product documentation)
Telemark reserves the right to make changes without prior notice. Illustrations may
vary depending on the version of the device.
Programmable Sweep Instruction Manual INTRODUCTION
telemark.com 8 of 58 Rev 1.0.0
1.3 Safety
1.3.1 Personnel Qualifications
All work described in this document may only be carried out by persons who have
suitable technical training and the necessary experience or who have been instructed
by the end user of the product.
1.3.2 Illustration of Residual Dangers
This Operating Manual illustrates safety notes concerning residual dangers as
follows:
Information on preventing any kind of physical injury.
Information on preventing extensive equipment and environmental damage.
Information on correct handling or use. Disregarding safety notes can lead to
malfunctions or equipment damage.
Note: Indicates particularly important, but not safety-relevant information.
DANGER
!
WARNING
!
CAUTION
!
Programmable Sweep Instruction Manual INTRODUCTION
telemark.com 9 of 58 Rev 1.0.0
1.4 General Safety Instructions
For all work you are going to do, adhere to the applicable safety regulations. Also
observe all safety notes given in this document and forward the information to all
other users of the product. Pay attention to the following safety notes:
Figure 1-1, Keep Foreign Material Out of the Programmable Sweep
Improper use.
Improper use can damage the Programmable Sweep.
Use the Programmable Sweep only as intended by the
manufacturer.
WARNING
!
Mains voltage.
Contact with live parts is extremely hazardous when any objects are
introduced, or any liquids penetrate the device.
Make sure that no objects enter the device. Keep the device dry.
DANGER
!
Programmable Sweep Instruction Manual INTRODUCTION
telemark.com 10 of 58 Rev 1.0.0
Improper installation and operation data.
Improper installation and operation data may damage the
Programmable Sweep.
Strictly adhere to the stipulated installation and operation data.
WARNING
!
Tabla de contenidos
Manuales populares de Electricidad industrial de otras marcas
S&C
S&C Vista SD Manual de usuario
Murata
Murata GRM0335C2A7R3CA01 Series Manual de usuario
Siemens
Siemens 3VA9988-0BM10 Manual de usuario
Siemens
Siemens SITRANS LVS100 Manual de usuario
Murata
Murata GRM32ER60G227ME05 Series Manual de usuario
Siemens
Siemens SENTRON SUPERSWITCH 3KL82 Series Manual de usuario