Teledyne T3PS12415 Manual de usuario

    







This manual contains proprietary information, which is protected by

copyrights. All rights are reserved. No part of this manual may be

photocopied, reproduced or translated to another language without

prior written consent of Teledyne LeCroy company.

The information in this manual was correct at the time of printing.

However, Teledyne LeCroy continues to improve products and

reserves the rights to change specification, equipment, and

maintenance procedures at any time without notice.

SAFETY INSTRUCTION

Table of Contents

SAFETY INSTRUCTION .................................................... 4

OVERVIEW ...................................................................... 9

Main Features........................................................10

Model Differences .................................................10

Front Panel Overview .............................................11

CV/CC Crossover Characteristics ...........................13

Rear Panel Overview ..............................................14

Output Current/Temperature Characteristics .........16

SETUP ........................................................................... 17

Installation Location..............................................18

Power Up ...............................................................18

Over Voltage Protection Set Up .............................19

Load Cable Connection ..........................................20

Setting the Current Level .......................................22

Setting the Remote Control ...................................23

OPERATION .................................................................. 24

Constant Voltage Mode..........................................25

Using the Sense Terminals.....................................26

PERFORMANCE ADJUSTMENT ...................................... 27

APPENDIX ..................................................................... 33

Fuse Replacement..................................................33

Specification..........................................................34

INDEX ........................................................................... 36

T3PS1000 series User Manual

SAFETY INSTRUCTION

This chapter contains important safety

instructions that you must follow when operating

the T3PS power supply and when keeping it in

storage. Read the following before any operation

to insure your safety and to keep the power

supply in the best possible condition.

Safety Symbols

These safety symbols may appear in this manual or on the T3PS.

WARNING

Warning: Identifies conditions or practices that

could result in injury or loss of life.

CAUTION

Caution: Identifies conditions or practices that

could result in damage to the power supply or to

other objects or property.

DANGER High Voltage

Attention: Refer to the Manual

Protective Conductor Terminal

Earth (Ground) Terminal

Do not dispose electronic equipment as unsorted

municipal waste. Please use a separate collection

facility or contact the supplier from which this

instrument was purchased.

POWER

I Power On; connected to AC mains.

O Power Off; disconnected from AC mains.

SAFETY INSTRUCTION

Safety Guidelines

General Guideline

CAUTION

Do not place heavy objects on the power supply.

Avoid severe impact or rough handling that

may damage the power supply.

Avoid discharges of static electricity on or near

the power supply.

Use only mating connectors, not bare wires, for

the terminals.

Do not block the cooling fan vent.

The power supply should only be disassembled

by a qualified technician.

(Measurement categories) EN 61010-1:2010 specifies the

measurement categories and their requirements as follows. The

T3PS falls under category II.

Measurement category IV is for measurement performed at the

source of a low-voltage installation.

Measurement category III is for measurement performed in a

building installation.

Measurement category II is for measurement performed on

circuits directly connected to a low voltage installation.

Measurement category I is for measurements performed on

circuits not directly connected to Mains.

Power Supply

WARNING

AC Input voltage: 115V / 230V ±15%

47 ~ 63Hz

Connect the protective grounding conductor of

the AC power cord to an earth ground

Fuse

WARNING

Fuse type: 115V input: T 10A 250V; 230V input:

T 6.3A 250V

To ensure fire protection, replace the fuse only

with the specified type and rating.

Disconnect the power cord before replacing the

fuse.

Make sure the cause of fuse blowout is fixed

T3PS1000 series User Manual

before replacing the fuse.

Cleaning the

power supply

Disconnect the power cord before cleaning the

power supply.

Use a soft cloth dampened in a solution of mild

detergent and water. Do not spray any liquid

into the power supply.

Do not use chemicals containing harsh products

such as benzene, toluene, xylene, and acetone.

Operation

Environment

Location: Indoor, no direct sunlight, dust free,

almost non-conductive pollution (Note below)

Relative Humidity: < 80%

Altitude: < 2000m

Temperature: 0°C to 40°C

(Pollution Degree) EN 61010-1:2010 specifies pollution degrees and

their requirements as follows. The power supply falls under degree

Pollution refers to “addition of foreign matter, solid, liquid, or

gaseous (ionized gases), that may produce a reduction of dielectric

strength or surface resistivity”.

Pollution degree 1: No pollution or only dry, non-conductive

pollution occurs. The pollution has no influence.

Pollution degree 2: Normally only non-conductive pollution

occurs. Occasionally, however, a temporary conductivity caused

by condensation must be expected.

Pollution degree 3: Conductive pollution occurs, or dry, non-

conductive pollution occurs which becomes conductive due to

condensation which is expected. In such conditions, equipment

is normally protected against exposure to direct sunlight,

precipitation, and full wind pressure, but neither temperature

nor humidity is controlled.

Storage

environment

Location: Indoor

Relative Humidity: < 70%

Temperature: -10°C to 70°C

Select AC Voltage

CAUTION

Before powering up the power supply,

select the AC input voltage from the rear

panel.

115

AC LINE SELECT

SAFETY INSTRUCTION

Disposal

Do not dispose this instrument as unsorted

municipal waste. Please use a separate collection

facility or contact the supplier from which this

instrument was purchased. Please make sure

discarded electrical waste is properly recycled to

reduce environmental impact.

T3PS1000 series User Manual

Power cord for the United Kingdom

When using the T3PS in the United Kingdom, make sure the power

cord meets the following safety instructions.

NOTE: This lead/appliance must only be wired by competent persons

WARNING: THIS APPLIANCE MUST BE EARTHED

IMPORTANT: The wires in this lead are coloured in accordance with

the following code:

Green/ Yellow:

Earth

Blue:

Neutral

Brown:

Live (Phase)

As the colours of the wires in main leads may not correspond with the

colours marking identified in your plug/appliance, proceed as follows:

The wire which is coloured Green & Yellow must be connected to the

Earth terminal marked with the letter E or by the earth symbol or

coloured Green or Green & Yellow.

The wire which is coloured Blue must be connected to the terminal

which is marked with the letter N or coloured Blue or Black.

The wire which is coloured Brown must be connected to the terminal

marked with the letter L or P or coloured Brown or Red.

If in doubt, consult the instructions provided with the equipment or

contact the supplier.

This cable/appliance should be protected by a suitably rated and

approved HBC mains fuse: refer to the rating information on the

equipment and/or user instructions for details. As a guide, cable of

0.75mm2should be protected by a 3A or 5A fuse. Larger conductors

would normally require 13A types, depending on the connection

method used.

Any moulded mains connector that requires removal /replacement

must be destroyed by removal of any fuse & fuse carrier and disposed

of immediately, as a plug with bared wires is hazardous if a engaged in

live socket. Any re-wiring must be carried out in accordance with the

information detailed on this label.

OVERVIEW

This chapter describes the T3PS series of power

supplies, including their main features and front

/ rear panel introduction. After going through

the overview, follow the Setup chapter (page 17)

to properly power up and set operation

environment.

For initial inspection, refer to the Performance

adjustment chapter (page27).

Main Features ....................................................... 10

Model Differences................................................. 10

Front Panel Overview ............................................ 11

CV/CC Crossover Characteristics .......................... 13

Rear Panel Overview ............................................. 14

Output Current/Temperature Characteristics ........ 16

T3PS1000 series User Manual

Main Features

Features

Broad input power range: For 115V (97~133V),

for 230V (195V~265V)

High frequency switching power

High power Density

High efficiency (70%)

Constant voltage and constant current operation

Remote output control (on/off)

Model Differences

Model name

Voltage

Current

Watts

T3PS11230

12V

30A

360

T3PS12415

24V

15A

360

T3PS16006

60V

360

Este manual sirve para los siguientes modelos

Tabla de contenidos

Otros manuales de Fuente de alimentación de Teledyne

Teledyne

Teledyne T3PS40381P Manual del propietario

Teledyne

Teledyne T3PS40381P Manual de usuario

Teledyne

Teledyne Power Pod 400 Manual de usuario

Teledyne

Teledyne T3PS20051P Manual de usuario

Teledyne

Teledyne Power Pod 400 Manual de usuario

Teledyne

Teledyne HASTINGS 200 Series Manual de usuario

Teledyne

Teledyne T3PS3000 Manual de usuario

Teledyne

Teledyne Battery-Backed Power Supply Instrucciones de funcionamiento

Teledyne

Teledyne T3PS16081P Manual de usuario

Teledyne

Teledyne 3190 Series Manual de usuario

Teledyne

Teledyne T3PS13206 Manual de usuario

Teledyne

Teledyne T3PS30721P Manual de usuario

Teledyne

Teledyne T3PS36006 Manual de usuario

Teledyne

Teledyne 913 Instrucciones de funcionamiento

Teledyne

Teledyne T3PS13206P Manual de usuario

Teledyne

Teledyne LeCroy T3PS Series Manual de usuario

Teledyne

Teledyne T3PSX3200P Series Manual de usuario

Manuales populares de Fuente de alimentación de otras marcas

Monacor

Monacor PS-12CCD Manual de usuario

VOLTIMA

VOLTIMA MagicBox 15 Manual de usuario

Agilent Technologies

Agilent Technologies 6032A Manual de usuario

Miller

Miller Auto Deltaweld 452 Manual de usuario

BCP

BCP PUOUBK Hoja de instrucciones

HC 2210 Manual de usuario

Puls

Puls CT5.241 Manual de usuario

OCZ

OCZ ZX1250W Manual de usuario

iseg

iseg ECH 238 Manual de usuario

Power

Power XXL A Series Manual de usuario

Agilent Technologies

Agilent Technologies 6631B Manual de usuario

Renogy

Renogy PHOENIX 300 Manual de usuario

HP 6200B Manual de servicio

Epson

Epson Stylus Scan 2500 Manual de funcionamiento

Pulsar

Pulsar GREEN POWER CCTV PoE POE044816 Manual de usuario

Puls

Puls MiniLine ML50.100 Manual de usuario

Puls

Puls AS-Interface SLA4.100 Manual de usuario

Kenwood

Kenwood PS-60 Manual de usuario