Teledyne 5800 Manual de usuario

5800 Sampler

Pump Heater

Installation Instructions

Overview

This instruction sheet describes the steps to install

the optional pump heater inside the pump cover of both

the 5800 and 4700 Samplers. The heater prevents liquid

from freezing inside the pump under extremely cold con-

ditions.

Note

The heater prevents liquid from freezing only inside

the pump housing cover. In extremely cold climates,

you must also route the suction line correctly to

prevent liquid from freezing in the suction line. The

suction line must have a continuous slope. Do not

allow loops or low spots in the line where liquid can

remain between samples. (This general practice

applies to all climates to prevent sample

cross-contamination.)

Required Parts and Tools

●Heater Installation Kits

❍68-4700-104 for 115 VAC Samplers

❍68-5800-060 for 230 VAC Samplers

●#2 Phillips screwdriver

●Hack saw

●Fine sand paper or file

Installation

The Heater Installation Kit includes a heater, a heat

shield, self-tapping screws, and a clip to secure the AC

line cord. To install the kit:

1. Refer to Figure 1. If a notch is not present, cut a

notch in the pump cover with a hack saw or sim-

ilar tool. Use sand paper or a file to remove burrs

and smooth the cut edge.

Figure 1: Cut a notch in the top cover

for the AC line

cord to pass through

2. Fit the heat shield inside the pump cover as

shown in Figure 2. Secure the shield with the

four #63/8" self-tapping screws.

Figure 2: Install heat shield inside cover

13 mm

(1/2in)

Instruction Sheet 69-4703-150

Revision D, February 1, 2016

Teledyne Isco

P.O. Box 82531, Lincoln, Nebraska, 68501 USA

Toll-free: (866) 298-6174 • Phone: (402) 464-0231 • Fax: (402) 465-3001

E-mail: [email protected]

Teledyne Isco is continually improving its products and reserves the right to change product

specifications, replacement parts, schematics, and instructions without notice.

3. Temporarily close the pump cover to check the

heat shield alignment. The hole in the shield

must fit over the large knob on the pump assem-

bly. If the shield hits the knob, loosen the four

screws and adjust the shield. Tighten the screws

when the alignment is correct.

4. Position the heater on the sampler as shown in

Figure 3. Align the edges of the slot in the heater

against the lower left corner of the pump

assembly.

Figure 3: Install heater under pump

5. Secure the heater in place with the two #142"

self-tapping screws. Tighten the screws until

fully seated.

6. Refer to Figure 4 and secure the AC line cord

with the clip and the #85/8" self-tapping screw.

Figure 4: Install line cord clip

just inside the notch in

the cover.

Assistance Available

Should you need assistance with these instructions,

contact Teledyne Isco.

Last modified February 1, 2016

3 mm

(1/8 in)

30 mm

(1.2 in)

Otros manuales para 5800

Otros manuales de Equipo de laboratorio de Teledyne

Teledyne

Teledyne 4700 Manual de usuario

Teledyne

Teledyne 10 Instrucciones de funcionamiento

Teledyne

Teledyne CETAC ASX-112FR Manual de usuario

Teledyne

Teledyne CombiFlash Companion XL Manual de usuario

Teledyne

Teledyne Foxy R1 Manual de usuario

Teledyne

Teledyne Everywhereyoulook IsoPlane 320A Manual de usuario

Teledyne

Teledyne ADX-500 Manual de usuario

Teledyne

Teledyne 934 NiCad Manual de usuario

Teledyne

Teledyne Tekmar 7000 Manual de usuario

Teledyne

Teledyne ACCQPrep HP125 Instrucciones de funcionamiento

Teledyne

Teledyne ACCQPrep AI 5 Manual de usuario

Teledyne

Teledyne T640 Manual

Teledyne

Teledyne FALCON GC Manual de usuario

Teledyne

Teledyne Platinum Manual de usuario

Teledyne

Teledyne 5800 Manual de usuario

Teledyne

Teledyne Hanson Research FLODEX Manual de usuario

Teledyne

Teledyne AutoInjector Module Instrucciones de funcionamiento

Teledyne

Teledyne 3700 Instrucciones de funcionamiento

Teledyne

Teledyne XTRX500 Manual de usuario

Teledyne

Teledyne 4700 Manual de instrucciones

Teledyne

Teledyne Installation Guide Manual de usuario

Teledyne

Teledyne CombiFlash Torrent Manual de usuario

Teledyne

Teledyne ASX-560 Manual de usuario

Teledyne

Teledyne CombiFlash NextGen Instrucciones de funcionamiento

Manuales populares de Equipo de laboratorio de otras marcas

Qiagen

Qiagen DML 3000 Manual de usuario

Queensgate

Queensgate NANOSCAN OP400 Manual de programación

Conviron

Conviron GEN1000-GE Manual de usuario

Parr Instrument

Parr Instrument 4560 Manual de instrucciones

IKA

IKA IC control Manual de usuario

Integra

Integra DOSE IT Manual de usuario

Agilent Technologies

Agilent Technologies 5800 ICP-OES Manual de usuario

Endress+Hauser

Endress+Hauser Cleanfit CPA875 Manual de usuario

NI PXI-5422 Manual

Collomix

Collomix Aqix Manual de usuario

SPEX SamplePrep

SPEX SamplePrep 6875 Freezer/Mill Series Manual de usuario

Ocean Insight

Ocean Insight FLAME-NIR+ Manual de usuario

Parker

Parker ALIGN-MG-NA Manual de usuario

BD 644787 Manual de usuario

DENTAURUM

DENTAURUM Compact Megaplus Manual de usuario

Biuged Laboratory Instruments

Biuged Laboratory Instruments BGD 626 Manual de usuario

VWR

VWR SAS Super IAQ Manual de usuario

illumina

illumina MiSeqDx Manual de usuario