Telect LTX Manual de usuario

LTX

Patch and Splice Panel

Installation Guide

LTX Patch and Splice Panel

Installation Guide

1.509.926.6000 :: telect.com 2

Table of Contents

Chapter 1: Introduction...........................................................................................................................................4

1.1 Specications .................................................................................................................................................4

1.2 About this Guide .............................................................................................................................................5

1.3 Terminology ....................................................................................................................................................5

1.4 LTX 4RU, 2RU and 1RU Panel Overview ......................................................................................................6

Chapter 2: Installation Considerations..................................................................................................................9

2.1 Inspection .......................................................................................................................................................9

2.2 Unpacking.......................................................................................................................................................9

2.2.1 LTX 4RU, 2RU and 1RU Panel Contents ...............................................................................................10

2.3 Installation Guidelines .................................................................................................................................. 11

2.4 Location and Space...................................................................................................................................... 11

2.5 Tools and Equipment.................................................................................................................................... 11

Chapter 3: LTX Patch and Splice Panel Installation and Routing.....................................................................12

3.1 LTX Panel Component Installation ...............................................................................................................12

3.1.1 Entry/Exit Arc Installation........................................................................................................................12

3.1.2 Routing Spool Installation.......................................................................................................................12

3.1.3 Splice Tray Installation............................................................................................................................13

3.1.4 Tray Platform Installation........................................................................................................................15

3.1.5 Cable Clamp Bracket Installation ...........................................................................................................15

3.1.6 Cable Clamp Installation.........................................................................................................................17

3.1.7 Central Strength Member Holder Installation .........................................................................................18

3.1.8 Adapter Patch Plate Installation..............................................................................................................19

3.1.9 Panel Doors Installation..........................................................................................................................20

3.1.10 Designation Label Installation...............................................................................................................21

3.1.11 Installing Mounting Brackets on the LTX Panel ....................................................................................22

3.2 Install and Ground the LTX Panel on the Rack ............................................................................................23

Chapter 4: LTX Panel Cable and Fiber Installation and Routing.......................................................................24

4.1 Cable Installation and Routing......................................................................................................................24

4.1.1 IFC Cable Installation and Routing.........................................................................................................24

4.1.2 Install IFC in the Cable Clamp................................................................................................................25

4.1.3 Route Protected 12 Strand Ribbon Fiber in LTX Panel Slack Storage Area .......................................... 26

4.1.4 Install Ribbon Fibers in the Splice Tray .................................................................................................. 27

4.1.5 Route Pigtail Fibers in the Splice Tray....................................................................................................28

4.2 Splice and Route Fibers ...............................................................................................................................31

4.3 Connect Fiber Jumpers to the Patch Panel..................................................................................................31

Chapter 5: Service.................................................................................................................................................34

5.1 Owner Maintenance .....................................................................................................................................34

5.1.1 High Insertion Loss and the Importance of Cleaning Connectors and Adapters....................................34

5.2 Techincal Support.........................................................................................................................................35

5.3 In-Warranty Service......................................................................................................................................35

5.4 Out-of-Warranty Service...............................................................................................................................35

5.5 Repackage for Shipment..............................................................................................................................35

LTX Patch and Splice Panel

Installation Guide

1.509.926.6000 :: telect.com 3

List of Figures

Figure 1-1 LTX Patch and Splice Panel with SC Adapters ........................................................................................4

Figure 1-2 LTX 4RU Patch and Splice Panel Overview - Front and Rear Views ......................................................6

Figure 1-2-1 LTX 2RU Patch and Splice Panel Overview - Front and Rear Views ...................................................7

Figure 1-2-2 LTX 1RU Patch and Splice Panel Overview - Front and Rear Views ...................................................8

Figure 3-1 Entry/Exits Arcs Installation....................................................................................................................12

Figure 3-2 Routing Spools Installation.....................................................................................................................12

Figure 3-3 4RU Splice Trays Installation .................................................................................................................13

Figure 3-3-1 2RU Splice Trays Installation..............................................................................................................14

Figure 3-3-2 1RU Splice Trays Installation..............................................................................................................14

Figure 3-4 4RU Tray Platform Installation ...............................................................................................................15

Figure 3-5 4RU Cable Clamp Bracket Installation...................................................................................................15

Figure 3-5-1 2RU Cable Clamp Bracket Installation................................................................................................16

Figure 3-5-2 1RU Cable Clamp Bracket Installation................................................................................................16

Figure 3-6 4RU Cable Clamp Installation................................................................................................................17

Figure 3-6-1 2RU Cable Clamp Installation.............................................................................................................17

Figure 3-6-2 1RU Cable Clamp Installation.............................................................................................................17

Figure 3-7 4RU Central Strength Member Holder Installation.................................................................................18

Figure 3-8 4RU Adapter Patch Plate Installation.....................................................................................................19

Figure 3-8-1 2RU Adapter Patch Plate Installation..................................................................................................19

Figure 3-8-2 1RU Adapter Patch Plate Installation..................................................................................................19

Figure 3-9 4RU Door Installation.............................................................................................................................20

Figure 3-9-1 2RU Door Installation..........................................................................................................................20

Figure 3-10 4RU Designation Label Installation......................................................................................................21

Figure 3-10-1 2RU Designation Label Installation...................................................................................................21

Figure 3-10-2 1RU Designation Label Installation...................................................................................................21

Figure 3-11 Installing Mounting Brackets on LTX 4RU Panels................................................................................22

Figure 3-11-1 Installing Mounting Brackets on LTX 2RU Panels.............................................................................22

Figure 3-11-2 Installing Mounting Brackets on LTX 1RU Panels.............................................................................22

Figure 3-12 Install and Ground LTX Panel to the Rack ........................................................................................... 23

Figure 4-1 Securing IFC Cabling to the LTX 4RU Panel .........................................................................................25

Figure 4-1-1 Securing IFC Cabling to the LTX 2RU Panel ......................................................................................25

Figure 4-1-2 Securing IFC Cabling to the LTX 1RU Panel ......................................................................................25

Figure 4-2 Route Protected 12-Stranded Ribbon Fiber through LTX Panel Slack Storage Area ............................26

Figure 4-3 Installing Ribbon Fibers in the Splice Tray.............................................................................................27

Figure 4-4 Routing Pigtail Fibers in the 4RU Splice Tray ........................................................................................28

Figure 4-4-1 Routing Pigtail Fibers in the 2RU Splice Tray..................................................................................... 29

Figure 4-4-2 Routing Pigtail Fibers in the 1RU Splice Tray..................................................................................... 30

Figure 4-5 Connecting Fiber Jumpers to the 4RU Patch Panel .............................................................................. 32

Figure 4-5-1 Connecting Fiber Jumpers to the 2RU Patch Panel ........................................................................... 33

Figure 4-5-2 Connecting Fiber Jumpers to the 1RU Patch Panel ........................................................................... 33

LTX Patch and Splice Panel

Installation Guide

1.509.926.6000 :: telect.com 4

Chapter 1: Introduction

The Telect LTX Patch and Splice Panel consolidates

network ber splicing, patching and routing

requirements in a 4RU panel.

The LTX panel accommodates up to 288 fiber

terminations and houses eight splice trays.

Front View

Rear View

144 Terminations Shown

Figure 1-1 - LTX Patch and Splice Panel with SC Adapters

1.1 Specications

Dimensions and Weights

Dimensions 4RU: 7" H x 17" W x 17" D

2RU: 3.5" H x 17" W x 17" D

1RU: 1.75" H x 17" W x 17" D

Weight 4RU: 14.65 lbs.

2RU: 11.2 lbs.

1RU: 6.8 lbs.

Mechanical

Connector Type SC/UPC, SC/APC, LC/APC, LC/UPC, MPO/MTP

Access Front and Rear

Capacity Max. 288 port 4RU

Splicing Single Fusion / Mass Fusion / Stranded

Panel Mounting 19" or 23" with ETSI, EIA, or WECO spacing

Adapter Access Front/Rear Patch Panel

Material Aluminum/Steel

Compliance NEBS, ETSI, Zone 4 Seismic reliability

Environmental

Temperature Range -5°C to 55°C

Humidity 90%, non-condensing

LTX Patch and Splice Panel

Installation Guide

1.509.926.6000 :: telect.com 5

1.2 About this Guide

This manual provides a comprehensive overview and installation guidelines for the LTX Patch and Splice Panel. While

care has been taken to dene all necessary information, complete details may not be covered. If you have any questions,

contact Telect at [email protected] or call 1.509.926.6000.

Throughout this guide, relevant and crucial information is displayed in the form of Notes, Alerts, Cautions and Warnings.

These notications are prominently displayed and their importance is indicated as follows:

NOTE: General information the user should pay special attention to.

Alert! Important information and/or instructions the user should adhere to.

CAUTION! Indicates a hazardous situation, which if not avoided could result in minor

or moderate injury.

WARNING: Indicates a potentially hazardous situation which if not avoided could result in death

or serious injury.

Telect assumes no liability from the application or use of these products. Neither does Telect convey any

license under its patent rights of others. This document and the products described herein are subject to change without

notice.

1.3 Terminology

The following list of acronyms and abbreviations are used throughout this manual.

Acronym/Abbreviation Term

IF IntraFacility Fiber

IFC IntraFacility Cable

LC Local Connector

MPO Multi-Fiber Push-On optical ber module interface type

NE Network Element

NEBS Network Equipment Building System (telecommunications product safety equipment rating

standard)

PC Physical Contact ber optic connector (single or multi-mode)

SC Standard Connector

TIA Telecommunications Industry Association

TIA/EIA-568 B.3 Telecommunication Standards for Commercial Cabling

TUV Technical Inspection Association (global product certication compliance marking)

UL Underwriter Laboratories (electrical standards)

APC Angled Physical Contact ber optic connector (single or multi-mode)

UPC Ultra Physical Contact ber optic connector (single or multi-mode)

LTX Patch and Splice Panel

Installation Guide

1.509.926.6000 :: telect.com 6

The Telect LTX patch and splice panel consolidates

network ber splicing, patching and routing requirements

in a 4RU panel.

The LTX 4RU panel accommodates:

• Up to 288 fiber terminations

• Stacked splice trays, housing 36 splice sleeve holders

per single fusion tray and 144 per mass fusion tray

• Single fusion/mass fusion options

• Velcro bands that secure trays inside the panel

• Routing spools to manage slack cable routing

• Panel mounted cable clamp for incoming cable

slack maintenance

• Convenient spring-hinged removable front and

rear doors

• Designation labels on front and rear doors

Interconnect and cross-connect cabling enter the LTX

panel at rear corner locations guided over rubber edge

protectors. Slack storage area in the rear of the panel

routes IntraFacility Cables (IFC) through the panel to

splice trays in the center of the panel. After splicing,

pigtail bers connect to patch plate mounted connectors

at the rear of the panel and ber jumpers connect to

patching adapters at the front.

LTX patch and splice panel patch plates

can accommodate:

• SC/UPC, SC/APC, LC/APC, LC/UPC are available in

patch plates with 6 or 8 terminations

• LC/SC available in patch plates with

12 terminations

• LC/UPC and LC/APC available in patch plates with

24 terminations

• MPO/MTP feed through patch plates available with 6

or 8 adapters

In addition, Telect offers a special factory-congured

integrated 4RU patch plate panel with up to 288

terminations (requires use of LC quad adapters).

Adapters are also offered in multi-mode versions. All

adapters include dust covers. All patch plates are

available in white or black.

1.4 LTX Panel Overview

Figure 1-2 - LTX 4RU Patch and Splice Panel Overview

- Front and Rear Views-

Rear Door

Routing Spool

Slack

Storage

Area

Designation Label

(Rear Side)

Cable Clamp Patch Plate with

Connectors

LTX Patch and Splice Panel, Rear View

(144 terminations shown)

Arc

Cable

Entry

Area Arc Stacked Splice

Trays

Cable

Entry Area

Arc

Velcro Tie

Arc

LTX Patch and Splice Panel, Front View

(144 terminations shown)

Front Door

Fiber

Jumper

Entry

Area

Designation

Card

(Front Side)

Patch Plate with Adapters

Cable Clamp

Arc

Arc Fiber

Jumper

Entry

Area

LTX 4RU

LTX Patch and Splice Panel

Installation Guide

1.509.926.6000 :: telect.com 7

LTX 1RU

The Telect LTX patch and splice panel consolidates

network ber splicing, patching and routing requirements

in a 1RU panel.

The LTX 1RU panel accommodates:

• Up to 72 fiber terminations

• Stacked splice trays, housing 36 splice sleeve holders

per single fusion tray and 144 per mass fusion tray

• Single fusion/mass fusion options

• Velcro bands that secure trays inside the panel

• Routing spools to manage slack cable routing

• Panel mounted cable clamp for incoming cable

slack maintanence

• Designation label on the front

Interconnect and cross-connect cabling enter the LTX

panel at rear corner locations guided over rubber edge

protectors. Slack storage area in the rear of the panel

routes IntraFacility Cables (IFC) through the panel to

splice trays in the center of the panel. After splicing,

pigtail bers connect to patch plate mounted connectors

at the rear of the panel and ber jumpers connect to

patching adapters at the front.

LTX patch and splice panel patch plates

can accommodate:

• SC/UPC, SC/APC, LC/APC, LC/UPC are available in

patch plates with 6 or 8 terminations

• LC/SC available in patch plates with

12 terminations

• LC/UPC and LC/APC available in patch plates with

24 terminations

• MPO/MTP feed through patch plates available with 6

or 8 adapters

In addition, Telect offers a special factory-congured

integrated 1RU patch plate panel with up to 72

terminations (requires use of LC quad adapters).

Adapters are also offered in multi-mode versions. All

adapters include dust covers. All patch plates are

available in white or black.

Figure 1-2-1 - LTX 1RU Patch and Splice Panel Overview

- Front and Rear Views-

Designation Label

LTX Patch and Splice Panel, Front View

(24 terminations shown)

Bracket

LTX Patch and Splice Panel, Rear View

(24 terminations shown)

Bracket Bracket

Routing Spool

Splice Tray

Patch Plate

Patch Plate with Adapters

Velcro Tie

LTX Patch and Splice Panel

Installation Guide

1.509.926.6000 :: telect.com 8

LTX 2RU

The Telect LTX patch and splice panel consolidates

network ber splicing, patching and routing requirements

in a 2RU panel.

The LTX 2RU panel accommodates:

• Up to 144 fiber terminations

• Stacked splice trays, housing 36 splice sleeve holders

per single fusion tray and 144 per mass fusion tray

• Single fusion/mass fusion options

• Velcro bands that secure trays inside the panel

• Routing spools to manage slack cable routing

• Panel mounted cable clamp for incoming cable

slack maintanence

• Convenient spring-hinged removable front and

rear doors

• Designation labels on front and rear doors

Interconnect and cross-connect cabling enter the LTX

panel at rear corner locations guided over rubber edge

protectors. Slack storage area in the rear of the panel

routes IntraFacility Cables (IFC) through the panel to

splice trays in the center of the panel. After splicing,

pigtail bers connect to patch plate mounted connectors

at the rear of the panel and ber jumpers connect to

patching adapters at the front.

LTX patch and splice panel patch plates

can accommodate:

• SC/UPC, SC/APC, LC/APC, LC/UPC are available in

patch plates with 6 or 8 terminations

• LC/SC available in patch plates with

12 terminations

• LC/UPC and LC/APC available in patch plates with

24 terminations

• MPO/MTP feed through patch plates available with 6

or 8 adapters

In addition, Telect offers a special factory-congured

integrated 2RU patch plate panel with up to 144

terminations (requires use of LC quad adapters).

Adapters are also offered in multi-mode versions. All

adapters include dust covers. All patch plates are

available in white or black. Figure 1-2-2 - LTX 2RU Patch and Splice Panel Overview

- Front and Rear Views-

LTX Patch and Splice Panel, Front View

(48 terminations shown)

LTX Patch and Splice Panel, Rear View

(48 terminations shown)

Designation Label

Patch Plate with Adapters

Front Door

Door Hinge

Bracket

Splice Tray Velcro Tie Routing

Spool

LTX Patch and Splice Panel

Installation Guide

1.509.926.6000 :: telect.com 9

Chapter 2: Installation Considerations

WARNING: Verify all connections meet requirements specied in local electric codes or operating company

guidelines before supplying power. Unit must be protected by a listed circuit breaker or branch-rated fuse

sufcient to interrupt power levels.

WARNING: Use of fully insulated tools is required when working with any AC or DC circuits.

WARNING: Fiber cables transmit invisible infrared light. To avoid eye damage or blindness, never look directly

into bers or connectors.

CAUTION! These instructions presume you have veried that the Telect equipment being installed is compatible

with the rest of the system including power, ground, circuit protection, signal characteristics, equipment from

other vendors and local codes or ordinances.

ALERT! This product must be installed and maintained only by qualied technicians.

ALERT! Install this system according to company requirements. It is recommended to install the

system in a Restricted Access Location (RAL) where access is limited through use of tool (i.e., lock and key) or

other means of security and be controlled by the authority responsible for the location.

ALERT! Prior to panel installation, ensure there is enough space in front and rear to access cabling.

ALERT! Only use components and crimping tools approved by agencies or certifying bodies recognized in your

country or region, such as Underwriter’s Laboratories (UL), TUV, etc.

ALERT! Do not stand on ber or ber cables.

2.1 Inspection

When you receive the equipment, carefully unpack it and compare it to the packaging list. Please report any defective

or missing parts to Telect at [email protected] or call 1.509.926.6000. Keep all documentation that comes with

your shipment.

Please read and understand all instructions before starting installation. If you have any questions, contact Telect at

[email protected] or call 1.509.926.6000.

The panel is wrapped with a high-strength plastic. Exercise care when unpacking and setting the equipment

in place.

Telect is not liable for transit damage. If the product is damaged, please report it to the carrier and

contact Telect at 1.509.926.6000 or through email at [email protected].

2.2 Unpacking

The LTX 4RU patch and splice panel is 7" H x 17" W x 17" D and weighs 14.65 lbs.

The LTX 2RU patch and splice panel is 3.5" H x 17" W x 17" D and weighs 11.2 lbs.

The LTX 1RU patch and splice panel is 1.75" H x 17" W x 17" D and weighs 6.8 lbs.

These panels come pre-assembled as one unit.

Upon receipt of your order, carefully unpack it and compare it with the packing list and the order placed. While items

described below are a comprehensive list that includes the LTX panel, splice trays with splice sleeves, spools, brackets,

and doors, the contents of your order may vary.

LTX Patch and Splice Panel

Installation Guide

1.509.926.6000 :: telect.com 10

2.2.1 LTX Panel Contents

4 RU

• LTX patch and splice panel

• Tray platform

• Splice trays

• Splice sleeve holders

• Arcs (edge protectors)

• Velcro bands

• Routing spools

• Removable doors (spring-hinged

swing down)

• Designation labels (front and rear)

• Cable clamp bracket

• Cable clamp with bushing sleeves

• Mounting brackets (to mount to 19" or

23" rack)

• Installation guide

2 RU

1 RU

• LTX patch and splice panel

• Splice trays

• Splice sleeve holders

• Arcs (edge protectors)

• Velcro bands

• Routing spools

• Removable doors (spring-hinged

swing down)

• Designation labels (front and rear)

• Cable clamp bracket

• Cable clamp with bushing sleeves

• Mounting brackets (to mount to 19" or

23" rack)

• Installation guide

• LTX patch and splice panel

• Splice trays

• Splice sleeve holders

• Arcs (edge protectors)

• Velcro bands

• Routing spools

• Designation labels (front)

• Cable clamp bracket

• Cable clamp with bushing sleeves

• Mounting brackets (to mount to 19" or

23" rack)

• Installation guide

Otros manuales para LTX

Tabla de contenidos

Otros manuales de Panel de control de Telect

Telect

Telect 009-8005-3404H Manual de usuario

Telect

Telect GMT Series Manual de usuario

Telect

Telect LTX Manual de usuario

Telect

Telect LCX Series Manual de usuario

Telect

Telect 009-8004-0208 Manual de usuario

Telect

Telect LCX Series Manual de usuario

Manuales populares de Panel de control de otras marcas

RDZ

RDZ PC-HRX Manual de usuario

STG-BEIKIRCH

STG-BEIKIRCH MZ3 Manual técnico

Efka

Efka Variocontrol V810 Manual de usuario

Cebora

Cebora 208-10 Manual de usuario

AMX

AMX AutoPatch CP-15 Manual de usuario

Satel

Satel CA-6 KLED-S Manual de usuario

Evolution

Evolution IQ plus 800 Manual de usuario

Fagor

Fagor 8040 TCO CNC Manual de usuario

Trane

Trane ComfortLink II XL950 Control Manual de usuario

AKO

AKO PROCool AKO-17635-2 Manual de usuario

ABB

ABB 6136/30M-101 Manual de usuario

Telikou

Telikou BK-603 Belt Pack Manual de usuario

Mapei

Mapei Mapeheat Thermo Touch Manual de usuario

Bosch

Bosch D9412GV4 Manual de usuario

Mitsubishi Heavy Industries

Mitsubishi Heavy Industries SC-SL4-AE2/1 Manual de usuario

Sminn

Sminn BOX L VF1L EI Manual de usuario

Balboa

Balboa TP600 Manual de usuario

Nice

Nice HSCU1 Especificaciones técnicas