Tektronix TDS 500C Manual de usuario
Supplement
TDS 500C, TDS 600B & TDS 700C
Digitizing Oscilloscopes
071-0090-01
This document supports firmware version 5.2 and
above.
Copyright Tektronix, Inc. All rights reserved.
Tektronix products are covered by U.S. and foreign patents, issued and pending. Information in this publication supercedes
that in all previously published material. Specifications and price change privileges reserved.
Printed in the U.S.A.
Tektronix, Inc., P.O. Box 1000, Wilsonville, OR 97070–1000
TEKTRONIX and TEK are registered trademarks of Tektronix, Inc.
TDS 500C, TDS 600B & TDS 700C Supplement 1
Introduction
This document contains three supplements to the TDS 500C, TDS 600B, and
TDS 700C manuals:
TDS 580C Supplement provides information that extends the TDS 500C,
TDS 600B, and TDS 700C manuals to cover a new oscilloscope model, the
TDS 580C Digitizing Oscilloscope. See page 3.
Version 5.2 Firmware Supplement provides information that extends the
manuals to cover the new or changed functions that are available in the
TDS 500C and TDS 700C oscilloscopes, starting with firmware version 5.2.
See page 5.
Option 1G Supplement provides information that extends the manuals to
cover two oscilloscope models, the TDS 540C and TDS 754C Option 1G
Oscilloscopes. See page 29.
Introduction
2TDS 500C, TDS 600B & TDS 700C Supplement
TDS 500C, TDS 600B & TDS 700C Supplement 3
TDS 580C Supplement
The TDS 500C, TDS 600B, and TDS 700C model oscilloscope manuals also
cover an oscilloscope model that is not mentioned in those manuals, the
TDS 580C.
This supplement lists the differences between the TDS 580C and the TDS 784C,
which is the model that the TDS 580C is most like.
Except for the differences shown in the table below, The TDS 580C is identical
to a TDS 784C. Most of the information in your user manual (and other TDS
documents) that applies to the TDS 784C, also applies to the TDS 580C.
Like the TDS 784C, the TDS 580C provides four full-function channels,
digitizing rates to 4 GS/second, a 1 GHz analog bandwidth, and up to 50 K
record lengths (or longer with options 1M or 2M). The table below lists the key
areas where the TDS 784C and the 580C differ:
Feature 784C 580C
Display Color Monochrome
FFT Yes Optional(2F)
RS232 and Centronics Port Yes Optional(13)
Accessory Pouch Standard Available
(016-1268-00)
All options listed for the TDS 784C are available for the TDS 580C. The
TDS 784C, and the TDS 580C ships without probes. The probe options are:
Option 24. Add four P6139A passive oscilloscope probes.
Option 26. Add four P6245 1.5 GHz FET oscilloscope probes.
The option 1G, detailed in Option 1G Supplement in this document, is not
available for the TDS 580C.
The TDS 580C comes with the firmware features listed in Version 5.2 Firmware
Supplement in this document; no upgrade is required. See page 5.
Key Features
Options
Firmware
TDS 580C Supplement
4TDS 500C, TDS 600B & TDS 700C Supplement
The TDS 500C, TDS 600B, and TDS 700C Service Manual (optional accessory)
applies to the TDS 580C.
Use the part number listed for the TDS 784C when replacing the following parts:
Circuit Board Assembly: Acquisition A10
Front Panel Assembly A12
Use the part number listed for the TDS 520C, TDS 540C, TDS 620B, and
TDS 680B when replacing the following parts:
Display, Monochrome: 7-Inch A20
Filter, Lt, Crt: 6.525 X 5.225, ESP, EMC
Retainer, Filter: Dust Seal Assembly, Lexan
Use part number 334-8551-01 when replacing the Front-Panel Identification
Label.
Service Information
TDS 500C, TDS 600B & TDS 700C Supplement 5
Version 5.2 Firmware Supplement
This supplement describes new or changed functions that are available starting
with firmware version 5.2.
Masks
Masks now include the following functions.
Table 1 contains a complete list of available masks.
Table 1: Standard masks
SONET
SDH ITU-T T1.102 Fibre channel Video Ethernet Miscellaneous
None None None None None None None
OC1/STM0
51.84Mb/s DS-0 Sgl
Single
64.4kb/s
DS1
1.544Mb/s FC133
Optical132.8 Mb/s 4fsc NTSC “D2”
143.18Mb/s GigabitEthernet
Optical 1.25 Gb/s FDDI Halt
125Mb/s
OC3/STM1
155.52Mb/s DS-0 Dbl
Double 64 kb/s DS1A
2.048Mb/s FC266
Optical265.6 Mb/s 4:2:2 “D1”
270Mb/s 100Base-TX
UTP 125 Mb/s
OC12/STM4
622.08Mb/s DS-0 Data
DataContra
64 kb/s
DS1C
3.152Mb/s FC531
Optical531.2 Mb/s 4:2:2SMPTE
259M-D
360Mb/s
100Base-TX
STP 125 Mb/s
DS-0 Tmg
Timing 64 kb/s DS2
6.312Mb/s FC1063
Optical1.0625 Gb/s 10 Base-T Idle (IDL)
Time Details 10 Mb/s
DS-1Rate
1.544Mb/s DS3 Full Mask
44.736Mb/s FC133E
Electrical132.7 Mb/s 10 Base-T Idle (IDL)
Volt Details 10 Mb/s
DS-3Rate
44.736Mb/s DS3 TimeDetails
44.736Mb/s FC266E
Electrical265.6 Mb/s 10 Base-T Idle (IDL)
Full Mask 10 Mb/s
E1 Sym
Sym Pair
2.048Mb/s
DS4NA
139.26Mb/s FC531E
Electrical531.2 Mb/s 10 Base-T Link Test
Time Details 10 Mb/s
E1 Coax
CoaxPair
2.048Mb/s
DS4NA Mx
MaxOutput
139.26Mb/s
FC1063E
Electrical
1.0625Gb/s
10 Base-T Link Test
Volt Details 10 Mb/s
E2
8.448Mb/s STS-1 Eye
Eye 51.84 Mb/s 10 Base-T Link Test
Full Mask 10 Mb/s
E3
34.368Mb/s STS-1
Pulse 51.84 Mb/s
Available Masks
Version 5.2 Firmware
6TDS 500C, TDS 600B & TDS 700C Supplement
Table 1: Standard masks (Cont.)
SONET
SDH MiscellaneousEthernetVideoFibre channelT1.102ITU-T
E4 0
Binary 0
139.26Mb/s
STS-3
155.52Mb/s
E4 1
Binary 1
139.26Mb/s
STS-3 Mx
MaxOutput
155.52Mb/s
E5 CEPT
565Mb/s
STM1E 0
Binary 0
155.52Mb/s
STM1E 1
Binary 1
155.52Mb/s
If on, mask pass/fail testing displays the results in the Pass/Fail Testing side
menu. To start mask pass/fail testing, press MEASURE ➞Measure (main) ➞
Masks (pop-up) ➞Mask Counting (main). Then toggle Pass/Fail Test (side) to
On.
The Pass/Fail Test side menu displays the testing status:
Passing is displayed if, for the requested number of acquired waveforms, the
number of hits does not exceed the number of hits specified in the failure
threshold
Failed is displayed if there are hits greater than or equal to the Pass/Fail
Failure Threshold in the masks in the requested number of acquired
waveforms
OFF Passed or OFF Failed is displayed when the test is complete, based on
the result of the test
Pass/fail testing turns on mask counting and resets the mask count to 0.
Hits greater than or equal to the Pass/Fail Failure Threshold are a test failure. To
set the threshold, press MEASURE ➞Measure (main) ➞Masks (pop-up) ➞
Mask Counting (main) ➞Pass/Fail Failure Threshold (side). Then use the
general purpose knob or keypad to set the failure threshold.
Pass Fail Testing
Set the Failure Threshold
Version 5.2 Firmware
TDS 500C, TDS 600B & TDS 700C Supplement 7
The test continues until the minimum number of waveforms has been acquired.
To set the minimum number of waveforms, press MEASURE ➞Mea-
sure (main) ➞Masks (pop-up) ➞Mask Counting (main) ➞Set Minimum
Number of Waveforms (side). Then use the general purpose knob or keypad to
set the number of waveforms.
The Pass/Fail Bell menu controls whether the mask pass/fail test rings a bell. To
control the Pass/Fail Bell, press MEASURE ➞Measure (main) ➞Masks
(pop-up) ➞Mask Counting (main). Then toggle Pass/Fail Bell (side) to Off,
On Failed, or On Completion.
Off does not ring a bell
On Completion rings the bell when the test is complete
On Failed rings the bell when a failure is detected and when the test is
complete
Use the procedures in your manual. Also, if a user mask is active, Autoset
adjusts the selected trace to match the last standard mask selected, if possible.
Use the HORIZONTAL POSITION control or the Time Base Position menu to
manually align the waveform to a mask. Adjusting the HORIZONTAL POSI-
TION resets mask counting.
Use Mask Margins to determine if your signal passes with a specific margin. To
set a mask margin do the following steps:
1. To enable mask margins, press MEASURE ➞Measure (main) ➞Masks
(pop-up) ➞Mask Margins (main). Then toggle Mask Margins (side) to
On or Off. If a user defined mask has more than three masks, turning on
mask margins will generate an error. Turning Mask Margins off will set the
Margin Percentage to 0%.
2. To set the margin percentage, press Margin Percentage (side). Then use the
general purpose knob or the keypad to set the percentage. Mask margin
percentage moves the mask boundaries to reflect the selected margin.
Negative margins make it easier to pass a mask test.
Set mask options to determine which waveform the masks are compared against,
to turn masks on or off, to enable Autoset to a mask, to enable offset adjustment
to masks, and to enable the digital waveform filter (see Figure NO TAG).
To select the channel that is compared against the selected mask, press MEA-
SURE ➞Measure (main) ➞Masks (pop-up) ➞Mask Options (main). Then
Set the Minimum Number
of Waveforms
Ringing the Bell
To Autoset the
Oscilloscope
Adjusting the Horizontal
Position
Setting Mask Margins
Setting Mask Options
Version 5.2 Firmware
8TDS 500C, TDS 600B & TDS 700C Supplement
toggle Mask Source (side) to Ch1, Ch2, Ch3, or Ch4. Mask Source is not
available in InstaVu II, because all on channels contribute to the mask.
To turn defined masks on or off, press MEASURE ➞Measure (main) ➞
Masks (pop-up) ➞Mask Options (main). Then toggle Mask Display (side)
ON or OFF.
To invert a DS1, DS1A, DS1C, DS2, DS3, E1 Sym, E1 Coax, E2, E3, STS-1,
STM1E, or E4 mask, press MEASURE ➞Measure (main) ➞Masks
(pop-up) ➞Mask Options (main). Then toggle Invert Mask (side) ON or OFF.
When ON and you select one of the above masks, the created mask is for a pulse
of opposite polarity to that of the standard mask.
Mask
Margins
OFF
Figure 1: Mask menu
NOTE. If you select Manual, some controls are automatically adjusted; if you
select Auto, a complete Autoset is performed. Also, if a user mask is active,
Autoset adjusts the selected trace to match the last standard mask selected, if
possible.
To control whether an autoset is performed when a standard mask is selected,
press MEASURE ➞Measure (main) ➞Masks (pop-up) ➞Mask Op-
tions (main). Then toggle Std Mask Autoset (side) to Auto or Manual.
Otros manuales para TDS 500C
1
Este manual sirve para los siguientes modelos
2
Tabla de contenidos
Otros manuales de Equipo de prueba de Tektronix
Tektronix
Tektronix TDS2012 Manual de usuario
Tektronix
Tektronix ths3000 series Guía del usuario
Tektronix
Tektronix 2205 Manual de usuario
Tektronix
Tektronix 516 series Manual de usuario
Tektronix
Tektronix TDS2000C series Manual de usuario
Tektronix
Tektronix 7T11A Manual de usuario
Tektronix
Tektronix P7380 Manual de usuario
Tektronix
Tektronix 507 Manual de usuario
Tektronix
Tektronix TBS2000 Series Manual de usuario
Tektronix
Tektronix A6302 Manual de usuario
Tektronix
Tektronix SD-24 Manual de usuario
Tektronix
Tektronix 7603 Manual de usuario
Tektronix
Tektronix TDS2000C series Manual de usuario
Tektronix
Tektronix P6248 Manual de usuario
Tektronix
Tektronix DPO2012 Manual de uso y cuidado
Tektronix
Tektronix 2245A Manual de usuario
Tektronix
Tektronix DPO2024 Manual de usuario
Tektronix
Tektronix TDS 700A Manual de usuario
Tektronix
Tektronix 7B70 Manual de usuario
Tektronix
Tektronix MSO70000C Series Manual de usuario
Manuales populares de Equipo de prueba de otras marcas
SMART
SMART KANAAD SBT XTREME 3G Series Manual de usuario
Agilent Technologies
Agilent Technologies BERT Serial Manual de usuario
Agilent Technologies
Agilent Technologies N3280A Manual de usuario
Vernier
Vernier Go Direct Voltage Manual de usuario
Lifeloc
Lifeloc R.A.D.A.R. Manual de usuario
Fluke
Fluke T5-600 Instrucciones de funcionamiento e instalación
