Tektronix TSG4100A-RM1 Manual de usuario

TSG4100A-RM1 and TSG4100A-RM2

RF Signal Generator

Rackmount Kit

ZZZ

Instructions

www.tektronix.com

*P075108300*

075-1083-00

or suppliers, and are protected by national copyright laws and international treaty provisions.

Tektronix products are covered by U.S. and foreign patents, issued and pending. Information in this publication

supersedes that in all previously published material. Speciﬁcations and price change privileges reserved.

TEKTRONIX and TEK are registered trademarks of Tektronix, Inc.

Contacting Tektronix

Tektronix, Inc.

14150 SW Karl Braun Drive

P.O. Box 500

Beaverton, OR 97077

USA

For product information, sales, service, and technical support:

In North America, call 1-800-833-9200.

Worldwide, visit www.tektronix.com to ﬁnd contacts in your area.

Table of Contents

Important safety information...................................................................................... 1

General safety summary ...................................................................................... 1

To avoid damage to equipment and personal injury ....................................................... 1

Kit descriptions and parts lists .................................................................................... 2

Equipment list.................................................................................................. 5

Installation instructions ............................................................................................ 5

RM1 installation ............................................................................................... 5

RM2 installation ............................................................................................... 7

TSG4100A Series RM1 and RM2 Rackmount Kit Instructions i

Table of Contents

ii TSG4100A Series RM1 and RM2 Rackmount Kit Instructions

Important safety information

This manual contains information and warnings that must be followed by the user

for safe operation and to keep the product in a safe condition.

To safely perform service on this product, additional information is provided at

the end of this section. (See page , Service safety summary.)

General safety summary

Review the following safety precautions to avoid injury and prevent damage to

this product or any products connected to it.

To avoid potential hazards, use this product only as speciﬁed.

Only qualiﬁed personnel should perform service procedures.

While using this product, you may need to access other parts of a larger system.

Read the safety sections of the other component manuals for warnings and

cautions related to operating the system.

To avoid damage to equipment and personal injury

Do not exceed rackmount weight ratings. Use this rackmount kit only for the

TSG4100A series instruments.

Use proper hardware. Do not interchange rack slides or rails with other hardware

or injury may result. Use only rails speciﬁed for the slides and mounting screws.

Use care when installing and removing product from rack. Use two people to

install and remove product from rack, one on each side. Avoid pinching ﬁngers

and hands when installing and removing. Do not force the product into the rails

when installing. Gently pull the product out when removing.

To prevent the instrument from tipping or dropping onto the installers, two or

more people should install this instrument into the rack cabinet. After completing

the installation procedure, the installers should verify that the instrument and rack

cabinet will not tip forward when the instrument is in the extended position.

The instrument may need to be extended for access to the rear panel. Do not leave

the instrument extended when ﬁnished accessing the rear panel.

Use only with speciﬁed products. Do not use rackmount on products for which

it was not intended. Refer to individual product manuals for details or contact

Tektronix Customer Service when in doubt.

TSG4100A Series RM1 and RM2 Rackmount Kit Instructions 1

Kit descriptions and parts lists

Once assembled, the following kits allow you to place one or two TSG4100A

Series RF Signal Generator(s) in a standard 19-inch equipment rack. Before

assembling your rackmount kit, check that you received all of the parts for the

particular kit you ordered.

2 TSG4100A Series RM1 and RM2 Rackmount Kit Instructions

Kit descriptions and parts lists

TSG4100-RM1 This kit conﬁgures one Tektronix TSG4100A Series RF Signal Generator for

mounting into a standard 19-inch equipment rack.

This kit shipped with the items listed in the following table and shown in the

following ﬁgure. (See Figure 1.)

When you are ready to assemble the rackmount kit, see the RM1 installation

procedure. (See page 5.)

Figure 1

reference Item Quantity

-1 Handle 2

-2 Screws, machine (8-32 x .375)

(These Torx 15 screws may already secure the handles to the

brackets.)

-3 Ear bracket, large 1

-4 Ear bracket, small 1

Figure 1: RM1 rackmount parts

TSG4100A Series RM1 and RM2 Rackmount Kit Instructions 3

Kit descriptions and parts lists

TSG4100-RM2 This kit conﬁgures two Tektronix TSG4100A Series RF Signal Generators for

mounting into a standard 19-inch equipment rack.

This kit shipped with the items listed in the following table and shown in the

following ﬁgure. (See Figure 2.)

When you are ready to assemble the rackmount kit, see the RM2 installation

procedure. (See page 7.)

Figure 2

reference Item Quantity

-1 Handle 2

-2 Ear bracket, small 2

-3 Screws, machine (8-32 x .375)

(Four of these Torx 15 screws may already secure the handles

to the brackets.)

-4 Plate, side interlocking 1

-5 Screws, sockethead cap (10-32 x .500) 4

-6 Bracket, side interlocking 2

Figure 2: RM2 rackmount parts

4 TSG4100A Series RM1 and RM2 Rackmount Kit Instructions

Installation instructions

Equipment list

Use the following tools to install the kit hardware:

Sockethead screwdriver

Torx T15 screwdriver

Torx T20 screwdriver

Torx T25 screwdriver

Flat-bladed screwdriver

Installation instructions

These instructions are for personnel who are familiar with servicing the product.

If you need further details for disassembling or reassembling the product, refer to

the appropriate product manual. Contact your nearest Tektronix Service Center or

contact Tektronix Factory Service for installation assistance.

RM1 installation

Use the following procedure and refer to the illustration to assemble the RM1

(single instrument) rackmount hardware and install the instrument into the rack.

(See Figure 3.)

CAUTION. You must remove the feet from the bottom of the instrument if you

intend to install it immediately above another instrument in the rack (with no

clearance). To so this, you will need to use a ﬂat-bladed screwdriver to pry out the

7/16"–deep plugs that cover the hidden screws, and then use a Torx T20 driver to

loosen the screws to remove the feet.

TSG4100A Series RM1 and RM2 Rackmount Kit Instructions 5

Installation instructions

Figure 3: RM1 assembly

RM1 assembly procedure 1. Remove the ﬂexible boot that surrounds and protect the front end of the

instrument.

2. Remove the two T25 screws from each side of the instrument (a total of 4

screws).

3. Attach the right handle bracket to the right (outside) side of the instrument

using two of the screws removed in step 1.

4. Attach the left handle bracket to the left (outside) side of the instrument using

the two remaining screws removed in step 1.

WARNING. To reduce the risk of injury or damage to the instruments that might be

caused by dropping the instruments or loading them into the rack incorrectly, use

two people to place and secure the instruments into the rack.

6. Place and secure the mounted instrument in the rack.

6 TSG4100A Series RM1 and RM2 Rackmount Kit Instructions

Este manual sirve para los siguientes modelos

Tabla de contenidos

Otros manuales de Generador portátil de Tektronix

Tektronix

Tektronix DTG5078 Manual de usuario

Tektronix

Tektronix AWG510 Manual de usuario

Tektronix

Tektronix TM 506 Manual de usuario

Tektronix

Tektronix TG8000 Manual de usuario

Tektronix

Tektronix AVG1 Manual de usuario

Tektronix

Tektronix AFG31000 Series Manual de usuario

Tektronix

Tektronix AWG610 Manual de usuario

Tektronix

Tektronix AFG3000 Series Manual de usuario

Tektronix

Tektronix AWG7000 Series Manual de usuario

Tektronix

Tektronix AWG5000B Series Manual de usuario

Tektronix

Tektronix CG 5001 Manual de usuario

Tektronix

Tektronix 106 Guía del producto

Tektronix

Tektronix AFG2000 Manual de usuario

Tektronix

Tektronix VITS 200 Manual de usuario

Tektronix

Tektronix AWG5000 Series Manual de usuario

Tektronix

Tektronix AWVG1 Manual de usuario

Tektronix

Tektronix SG 504 Manual de usuario

Tektronix

Tektronix AWG5200 Series Manual de uso y cuidado

Tektronix

Tektronix DG2040 Manual de usuario

Tektronix

Tektronix PatternPro PPG1600 Manual de usuario

Tektronix

Tektronix AWG5200 Series Manual de uso y cuidado

Tektronix

Tektronix AWG7000 Series Manual de uso y cuidado

Tektronix

Tektronix AWG5204 Manual de usuario

Tektronix

Tektronix AWG5000 Series Manual de usuario

Manuales populares de Generador portátil de otras marcas

Kohler

Kohler 20EORZ Manual de instrucciones

Powerhorse

Powerhorse 83171 Manual de usuario

HURST

HURST ML-630-SI Manual de usuario

ETQ

ETQ TG4000 Manual de usuario

Briggs & Stratton

Briggs & Stratton 40265 Guía de configuración

ConMed

ConMed 7550 Manual de usuario

Owon

Owon Waveform Generator Manual de usuario

evertz

evertz 7700 Series Manual de usuario

Power Stroke

Power Stroke PS906025 Manual de usuario

Firefly

Firefly Cygnus CYG2400/460/24 Manual de usuario

Draper

Draper PG950S Actualización de firmware

PowerBoss

PowerBoss PowerBoss Manual de usuario

SDMO

SDMO SH 4000 Manual de usuario

EINHELL

EINHELL STE 5500 Manual de usuario

Wanco

Wanco WI3000P Manual de usuario

Full Boar

Full Boar FBT-3300 Manual de usuario

Dwyer Instruments

Dwyer Instruments ASG Manual de usuario

Westinghouse

Westinghouse WH1000i Series Manual de usuario