Tektronix AWG7101 Manual de usuario

Revision A

www.tektronix.com

071207200

Instructions

AWG7000 Series

Arbitrary Waveform Generators

Declassification and Security

071-2072-00

Tektronix products are covered by U.S. and foreign patents, issued and pending. Information in this publication

supercedes that in all previously published material. Specifications and price change privileges reserved.

TEKTRONIX and TEK are registered trademarks of Tektronix, Inc.

Contacting Tektronix

Tektronix, Inc.

14200 SW Karl Braun Drive or P.O. Box 500

Beaverton, OR 97077

USA

For product information, sales, service, and technical support:

In North America, call 1-800-833-9200.

Worldwide, visit www.tektronix.com to find contacts in your area.

AWG7000 Series Declassification and Security i

Table of Contents

Preface . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . iii

Clear and Sanitize Procedures . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1

Memory Devices . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1

Media Storage and Data Export Devices . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5

Built-In Security Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5

Troubleshooting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6

How to Clear or Sanitize a Non-Functional Instrument . . . . . . . . . . . . . . . . . . . . . . . . . 6

How to Recover from Clearing or Sanitizing the Instrument’s Memory. . . . . . . . . . . . . 6

Table of Contents

ii AWG7000 Series Declassification and Security

AWG7000 Series Declassification and Security iii

Preface

This document helps customers with data security concerns to sanitize or remove

memory devices from the AWG7000 Series Arbitrary Waveform Generators.

These products have data storage (memory) devices and data output devices (USB

ports). These instructions tell how to clear or sanitize the memory devices and

disable the data output devices. The instructions also tell how to declassify an

instrument that is not functioning.

Products The following Tektronix products are covered by this document:

AWG7101 and all options

AWG7102 and all options

AWG7051 and all options

AWG7052 and all options

Related Documents AWG7000 Series Arbitrary Waveform Generators Service Manual, Tektronix

part number 071-1854-XX, available on the Tektronix Web site at

www.tektronix.com/manuals

AWG7000 Series Arbitrary Waveform Generators Hard Disk Drive Assembly

Installation Instructions, Tektronix part number 075-0922-XX, available on

the Tektronix Web site at www.tektronix.com/manuals

Preface

iv AWG7000 Series Declassification and Security

Terms The following terms may be used in this document:

Clear. This removes data on media/memory before reusing it in a secured area. All

reusable memory is cleared to deny access to previously stored information by

standard means of access.

Erase. This is equivalent to clear.

Media storage/data export device. Any of several devices that can be used to

store or export data from the instrument, such as a USB port.

Nonvolatile memory. Data is retained when the instrument is powered off.

Power off. Some instruments have a “Standby” mode, in which power is still

supplied to the instrument. For the purpose of clearing data, putting the instrument

in Standby mode does not qualify as powering off. For these products, you will

need to either press a rear-panel OFF switch or remove the power source from the

instrument.

Remove. A physical means to clear the data by removing the memory device from

the instrument. Instructions are available in the product service manual.

Sanitize. This eradicates the data from media/memory so that the data cannot be

recovered by other means or technology. This is typically used when the device

will be moved (temporarily or permanently) from a secured area to a non-secured

area.

Scrub. This is equivalent to sanitize.

User-modifiable. The memory device can be written to by the user during normal

instrument operation, using the instrument’s user interface or remote control.

Volatile memory. Data is lost when the instrument is powered off.

AWG7000 Series Declassification and Security 1

Clear and Sanitize Procedures

Memory Devices

The following tables list the volatile and nonvolatile memory devices.

Table 1: Volatile memory devices

Type and

minimum size Function

User

modifiable Data input method Location Process to clear

DDR2 SRAM

64 M x 64 bits

Microprocessor

system memory

Yes Written by processor

system

Micro-ATX board Remove the power source

from the instrument for at

least 20 seconds.

Pipelined SRAM

1 M x 72 bits

Waveform memory

for holding wave-

forms to generate

Yes Written by processor

system

AWG10G board Remove the power source

from the instrument for at

least 20 seconds.

Table 2: Nonvolatile memory devices

Type and

minimum size Function

User

modifiable1Data input method Location Process to sanitize

Removable hard

drive

Holds user-storable

data such as

waveforms and

instrument settings.

Yes Firmware operations Removable hard

drive slot on rear

panel.

Remove the hard drive and

store it in a secure area or

destroy it. When it is

removed, no user data

remains in the instrument.

(See page 4, Removable

Hard Drive.)

EEPROM

64 K

Contains model

configurations and

calibration data.

No Not accessible AWG10G board Not applicable

EEPROM

64 K

Contains model

configurations and

calibration data.

No Not accessible MIO board Not applicable

Flash,

128 K x 8 bits

Contains Video

BIOS for the LCD

display.

No Not accessible MIO board Not applicable

EEPROM

4 K

Contains MAC

address for TekLink.

No Not accessible MIO board Not applicable

(See page 3, To D i s a b l e

TekLink Using the Windows

Device Manager.)

EEPROM

4 K

Contains PCI Bus

configurations.

No Not accessible MIO board Not applicable

Clear and Sanitize Procedures

2AWG7000 Series Declassification and Security

Disabling USB and CD-RW

Capability

The following instructions give a method to disable the built-in USB and CD-RW

capability. Using the BIOS disables the devices for DOS programs, while the

Windows Device Manager disables the devices for Windows programs. These

procedures disable both USB and the CD-RW to prevent their use.

To Disable USB and CD-RW for Windows Using the Windows Device Manager.

1. Connect a PS2 mouse and a PS2 keyboard to the instrument before powering

on (because USB will be disabled).

2. Log on to the instrument as an administrator.

3. From the Windows Start menu, select Control Panel, and then select System.

4. Select the Hardware tab.

5. Click Device Manager.

6. Expand the Universal Serial Bus controllers entry by clicking the + next to it.

7. Double-click the first USB Root Hub entry.

8. Select the Power tab.

9. If the Device Description is anything other than Generic USB Hub (4 ports),

click the General tab, and select Do not use this device (disable) in the Device

Usage drop-down list.

10. Click OK.

11. Repeat steps 7 through 9 for each USB Root Hub shown in the Device Manager

window.

EEPROM

64 K

Contains count for

actuation of relays.

No Not writable OUT10G board Not applicable

1. During normal instrument operation.

Table 2: Nonvolatile memory devices (cont.)

Type and

minimum size Function

User

modifiable1Data input method Location Process to sanitize

NOTE. If you disable the USB, CD-RW, and LAN in the following procedures, you

cannot write new firmware to the hard drive. To do so, you will need to enable one

of these items.

NOTE. It is critical to leave the USB Root Hub operating, otherwise, the front panel

will not function. If the front panel does not function, the AWG application will not

run.

Clear and Sanitize Procedures

AWG7000 Series Declassification and Security 3

12. Expand DVD/CD-ROM drives in the Device Manager window.

13. Right-click TEAC DW-224E-C, and select Disable.

14. Reboot the instrument to make the changes effective.

15. We suggest that you password-protect the Windows Administrator account

and set up Guest accounts for end users so that these changes cannot be easily

reversed.

To disable LAN Ethernet

Connectivity Using the

BIOS

1. Press F2 during instrument Boot Up to go to the BIOS configuration menu.

2. Go to Advanced > Peripheral Configuration.

3. Set Onboard LAN to Disabled.

4. Press Esc one time to return to the main BIOS configuration menu.

5. Press F10, and select OK to save changes and exit. The LAN system will be

disabled and no longer allow data traffic in or out.

To Disable TekLink Using

the Windows Device

Manager

1. Connect a PS2 mouse and a PS2 keyboard to the instrument before powering

on (because USB will be disabled).

2. Log on to the instrument as an administrator.

3. From the Windows Start menu, select Control Panel, and then select System.

4. Select the Hardware tab.

5. Click Device Manager.

6. Expand the device category Network Adapters.

7. Double click on the Intel(R) PRO/100 M Network Connection. This will be the

Network Adapter located on the interface board in PCI slot 2.

8. Click the General tab, and select Do not use this device (disable) in the Device

Usage drop-down list.

To Disable GPIB Using the

Windows Device Manager

1. Connect a PS2 mouse and a PS2 keyboard to the instrument before powering

on (because USB will be disabled).

2. Log on to the instrument as an administrator.

3. From the Windows Start menu, select Control Panel, and then select System.

4. Select the Hardware tab.

5. Click Device Manager.

6. Expand the device category National Instruments GPIB Interfaces.

7. Right click on PCI-GPIB.

8. Select Disable from the list.

Clear and Sanitize Procedures

4AWG7000 Series Declassification and Security

Removable Hard Drive To Remove the Hard Drive. To remove the hard disk drive assembly, see the

instrument user online help (AWG Reference > Removable Hard Disk). You can

also refer to the AWG7000 Series HDD Installation Instructions, Tektronix part

number 075-0922-XX.

All user-storable data is stored on the rear-panel removable hard drive. There are

DOD-approved scrubbing software packages available for the hard drive.

Tektronix has no recommendations regarding the available packages.

After the hard drive has been scrubbed, the operating system and instrument

software can be reinstalled using the Operating System Restore DVD and Product

Software CD that ship with the instrument.

Scrubbing the hard drive will not affect calibration of the instrument, since the

factory calibration constants are stored on the MIO board, entirely separate from

any waveform data or setup files. You can completely erase or remove any secure

data without affecting the calibration of the instrument. You can also calibrate the

instrument in a nonsecure site, and then use the instrument in a secure area without

recalibration.

Este manual sirve para los siguientes modelos

Tabla de contenidos

Otros manuales de Generador portátil de Tektronix

Tektronix

Tektronix AWG7000 Series Manual de usuario

Tektronix

Tektronix TLA7PG2 Manual de usuario

Tektronix

Tektronix TG501 Manual de usuario

Tektronix

Tektronix AWG5204 Manual de usuario

Tektronix

Tektronix TG8000 Manual de operación y mantenimiento

Tektronix

Tektronix SPG 1000 Manual de usuario

Tektronix

Tektronix AWG7000 Series Manual

Tektronix

Tektronix ECO422D Manual de usuario

Tektronix

Tektronix AWG 2021 Manual de usuario

Tektronix

Tektronix 2901 Manual de usuario

Tektronix

Tektronix VITS 201 Manual de usuario

Tektronix

Tektronix AFG3000 Series Manual de usuario

Tektronix

Tektronix TSG 601 Manual de usuario

Tektronix

Tektronix SG 504 Manual de usuario

Tektronix

Tektronix FG501 Manual de usuario

Tektronix

Tektronix SG 5010 Manual de usuario

Tektronix

Tektronix TSG4100A Series Manual de operación y mantenimiento

Tektronix

Tektronix CFG253 Manual de usuario

Tektronix

Tektronix TG8000 Manual de usuario

Tektronix

Tektronix TG700 Manual de uso y cuidado

Tektronix

Tektronix TG700 Manual de usuario

Tektronix

Tektronix DTG5078 Manual de usuario

Tektronix

Tektronix PatternPro PPG1600 Manual de usuario

Tektronix

Tektronix FG 5010 Manual de usuario

Manuales populares de Generador portátil de otras marcas

Kohler

Kohler 20EORZ Manual de instrucciones

Powerhorse

Powerhorse 83171 Manual de usuario

HURST

HURST ML-630-SI Manual de usuario

ETQ

ETQ TG4000 Manual de usuario

Briggs & Stratton

Briggs & Stratton 40265 Guía de configuración

ConMed

ConMed 7550 Manual de usuario

Owon

Owon Waveform Generator Manual de usuario

evertz

evertz 7700 Series Manual de usuario

Power Stroke

Power Stroke PS906025 Manual de usuario

Firefly

Firefly Cygnus CYG2400/460/24 Manual de usuario

Draper

Draper PG950S Actualización de firmware

PowerBoss

PowerBoss PowerBoss Manual de usuario

SDMO

SDMO SH 4000 Manual de usuario

EINHELL

EINHELL STE 5500 Manual de usuario

Wanco

Wanco WI3000P Manual de usuario

Full Boar

Full Boar FBT-3300 Manual de usuario

Dwyer Instruments

Dwyer Instruments ASG Manual de usuario

Westinghouse

Westinghouse WH1000i Series Manual de usuario