Tektronix AFG310 Manual de usuario
Instructions Manual
016–1674–50
AFG310 & AFG320 Rackmount Kit
075-0288-50
www.tektronix.com
075028850
Copyright ©Tektronix Japan, Ltd. All rights reserved.
Copyright ©Tektronix, Inc. All rights reserved.
Tektronix products are covered by U.S. and foreign patents, issued and pending. Information in this publication supercedes
that in all previously published material. Specifications and price change privileges reserved.
Tektronix Japan, Ltd., 5–9–31 Kitashinagawa, Shinagawa–ku, Tokyo 141–0001 Japan
Tektronix, Inc., P.O. Box 500, Beaverton, OR 97077
TEKTRONIX and TEK are registered trademarks of Tektronix, Inc.
016-1674-50 Rackmount Kit i
Table of Contents
Kit Description 1.............................................
Minimum Tool and Equipment List 1.....................................
Kit Parts List 1........................................................
Installation Instructions 3.....................................
Preparing the Instrument 3.............................................
Installing the Instrument into the ack Adapter 7..........................
Installation into a Equipment ack 11.....................................
Exploded View and Dimensional Drawing 13......................
ii 016-1674-50 Rackmount Kit
List of Figure
Figure 1 : Location of slit where minus driver may be inserted 4. . . . .
Figure 2 : Construction of the handle retainer (cross section) 4. . . . . .
Figure 3 : Construction of the handle retainer (cross section) 5. . . . . .
Figure 4 : Feet and rear cover removal 6. . . . . . . . . . . . . . . . . . . . . . . . .
Figure 5 : Attaching bracket and panel 8. . . . . . . . . . . . . . . . . . . . . . . . .
Figure 6 : Attaching bracket to two instruments 9. . . . . . . . . . . . . . . . .
Figure 7 : Attaching panel 10. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Figure 8 : Installation into the equipment rack 11. . . . . . . . . . . . . . . . . .
Figure 9 : Cooling for Rackmounted instruments 12. . . . . . . . . . . . . . .
Figure 10 : Rack adapter exploded view 13. . . . . . . . . . . . . . . . . . . . . . . .
Figure 11 : Dimensional drawing of rack adapter 14. . . . . . . . . . . . . . . .
016-1674-50 Rackmount Kit iii
Service Safety Summary
WARNING. The servicing instructions are for use by qualified personnel only. To
avoid personal injury, do not perform any servicing unless you are qualified to
do so. Refer to the General Safety Summary in the Service Manual of each
instrument before performing any service.
WARNING. Dangerous shock hazards may be exposed when the instrument covers
are removed. Before proceeding, ensure the mainframe power switch is in the off
position. Then, disconnect the instrument from the power source.
CAUTION. Many components within this instrument are extremely susceptible to
static-discharge damage. Service the instrument only in a static-free environ-
ment. Observe standard handling precautions for static-sensitive devices while
installing this kit. Always wear a grounded wrist and foot strap while installing
this kit.
Do not perform internal service on this product unless another person capable of
rendering first aid and resuscitation is present.
To avoid injury, remove jewelry such as rings, watches, and other metallic
objects. Do not touch exposed connections and components when power is
present.
Dangerous voltages or currents may exist in this product. Disconnect power cord
from the power source, remove battery (if applicable), and disconnect test leads
before removing protective panels, soldering, or replacing components.
To prevent product overheating, provide proper ventilation.
Do Not Service Alone
Avoid Exposed Circuitry
Disconnect Power
Provide Proper Ventilation
iv 016-1674-50 Rackmount Kit
016-1674-50 Rackmount Kit 1
it Description
This kit includes parts and instructions for upgrading your AFG310/AFG320
instrument.
When newly installing Rackmount Kit, no special performance check is required.
Minimum Tool and Equipment List
The following table lists the tools you will need to upgrade the 016Ć1674Ć50
Rackmount Kit.
Tool Description
#2 Phillips tip Screwdriver Standard tool for M3 and M4 screws
FlatĆbladed screwdriver For removing the plastic cover on the handle bracket
it Parts List
The following table lists the parts included in the 016Ć1674Ć50 Rackmount Kit.
Number Quantity Part Number Description
1ą1 ea 407Ć4575Ć00 RACKET, RACK: EIA, STL
2ą1ea333Ć4276Ć00 PANEL, FILTER: AFG300, STL
3ą9ea211Ć0905Ć00 SCREW, MACHINE: M3 6MM L, PNH, STL, MFZN-C, CROSS REC
4ą1ea211Ć0959Ć00 SCREW, MACHINE: M4 5MM L, PNH, STL, MFZN-C, CROSS REC
5ą1 ea 075Ć0288Ć50 Rackmount Instruction Sheet
Introduction
2 016-1674-50 Rackmount Kit
016-1674-50 Rackmount Kit 3
Installation Instructions
This section contains the following information:
Hhow to prepare your instrument to attach the rack adapter
Hhow to attach the rack adapter to your instrument
HInstallation into equipment rack
Preparing the Instrument
This sub-section contains the following information:
HHandle Removal
HFeet Removal
HRear Cover Removal
NOTE. All parts removed from the instrument in this procedure should be saved.
You will need some of them to reconvert the instrument to a standard version at a
later time.
1. Insert the flat-bladed screwdriver into the slit between the block and the
cover. See Figure 1.
2. Release the latch of the cover using the flat-bladed screwdriver. See Figure 2
and refer to 1.
CAUTION. The latch of the cover can be released by lifting it up ward about 5
mm. Do not lift the cover more than necessary when releasing the latch. If so the
nail at the opposite side of the cover can be broken.
3. Remove the cover by sliding it sideways to the handle. See Figure 2 and
refer to 2.
4. Repeat step 1 through 3 for another cover to remove.
5. Using a #2 phillips tip screwdriver, remove the one screw (M4 10 mm)
securing the block and handle to the cabinet.
Handle Removal
Installation Introductions
4 016-1674-50 Rackmount Kit
6. Repeat step 5 for another screw to remove. Lift off the blocks and handle.
Power Cable
Cover
Block
Location o Slit
where latĆbladed
screwdriver may be
inserted.
Location o Slit
where latĆbladed
screwdriver may be
inserted.
Figure 1: Location of slit where flat-bladed screwdriver may be inserted
CAUTION. The latch of the cover can be released by lifting it up ward about 5
mm. Do not lift the cover more than necessary when releasing the latch. If so the
nail at the opposite side of the cover can be broken.
1
2
1
Cover
Block
Handle
Cross Section
o the Cover
Figure 2: Construction of the handle retainer (cross section)
Este manual sirve para los siguientes modelos
1
Tabla de contenidos
Otros manuales de Generador portátil de Tektronix
Tektronix
Tektronix AFG2000 Manual de usuario
Tektronix
Tektronix TSG4100A Series Manual de operación y mantenimiento
Tektronix
Tektronix AWG510 Manual de usuario
Tektronix
Tektronix AWG2005 Manual de usuario
Tektronix
Tektronix RTX130A Manual de usuario
Tektronix
Tektronix SW503 Manual de usuario
Tektronix
Tektronix TSG200 Manual de usuario
Tektronix
Tektronix AWG7000B Series Manual de usuario
Tektronix
Tektronix 067-1049-00 Manual de usuario
Tektronix
Tektronix 180A Manual de usuario
Tektronix
Tektronix DTG5078 Manual de usuario
Tektronix
Tektronix FG501 Manual de usuario
Tektronix
Tektronix FG501 Manual de usuario
Tektronix
Tektronix RTX130B Manual de usuario
Tektronix
Tektronix Tektronix SPG8000 Manual de uso y cuidado
Tektronix
Tektronix TG8000 Manual de operación y mantenimiento
Tektronix
Tektronix AFG2000 Manual de usuario
Tektronix
Tektronix SPG8000A Manual de usuario
Tektronix
Tektronix FG501 Manual de usuario
Tektronix
Tektronix FG501A Manual de usuario
