Tekno RC EB48SL SuperLight Manual de instrucciones

Introduction

Disclaimer: Tekno RC is not responsible or liable for any property or personal damage, loss, or

injury incurred as a result of using this product. This kit is meant for use by persons 14 years of

age or older and in the strict connes of a legally permitted RC track or facility.

Warnings: Always double-check that your radio gear is working properly before operating vehicle.

Never operate the vehicle indoors (unless the RC track is an indoor facility). Use caution while

operating vehicle so as not to collide with people who may be turn mashalling or who might

otherwise not be aware that a fast moving RC vehicle is in the vicinity.

Warranty: We warrant that the parts included in this kit are free from defects. If you nd a

defective part in your kit, please contact us @ [email protected] and we will help you to resolve

the issue. We do not warranty parts that may be broken during operation of the vehicle or

otherwise. Refer to the end of this instruction manual for a listing of spare/replacement and

option parts. All spare parts and other info are available on our website (www.teknorc.com)

and through our network of domestic and international dealers and distributors.

Additional equipment and parts needed:

2/3 channel radio transmitter and receiver

1/10th scale SC (4 pole) ESC and motor

High torque steering servo

2s LiPo battery

1/8th scale buggy tires, wheels & CA glue

Paint for Body

MOD1 Pinion (TKR4171->TKR4190)

Tools needed:

Hex drivers (1.5mm, 2.0mm, 2.5mm)

Nut drivers (5.0mm, 5.5mm, 7.0mm)

17mm Wheel Wrench

Hobby knife

Needle-nose pliers

Adjustable (Crescent) wrench (for shock assembly)

4mm turnbuckle wrench

Lexan Body Scissors

Thank you for purchasing the Tekno RC EB48SL 1/8th Scale Electric Super Light Buggy.

The EB48SL is a super light 1/8th scale buggy that runs a 2 cell pack and SC 4 pole motor. We are always

working on new projects, so please check our website (www.teknorc.com) regularly for the latest

news, parts, and kits. Thanks again.

Apply grease to the groove

where the o-ring is placed

as well as the o-ring itself

Apply grease to the groove in the outdrive

Fill with 7000 wt oil to

1mm below full

DO NOT OVER FILL

TKR5145B

TKR5144

Bag A

Center Differential

(overview)

TKR5237K

TKR5149X

TKR5150

TKR5143

TKR5113

*TKR5237

*TKR5115

(Option)

TKR1325

M3x14mm Flat Head Screw

TKR5144

TKR5145B

TKRBB08165

Ball Bearing(8x16x5mm)

TKR5144

Differential 0-rings

TKR5145B

Differential Shims (6x17mm)

TKR1325 x4

TKR5149X

TKRBB08165

Diff

Oil

TKR5614X

TKR5150

TKR5144

Grease

Step

A-2

Step

A-1

Step

A-4

Step

A-3

*TKR5149A

(Option)

*TKR5149A

(Option)

Apply grease to the groove

where the o-ring is placed

as well as the o-ring itself

Apply grease to the groove in the outdrive

Repeat for rear di

Fill FRONT with 7000 wt oil front

Fill REAR with 5000 wt oil rear

to1mm below full

DO NOT OVER FILL

Repeat for rear di

TKR5149X

*TKR5149A

(Option)

*TKR5149A

(Option)

TKR5145B

TKR5144

Bag B

Front and Rear Differential

(overview)

TKR5151

TKR5149X

TKR5150

TKR5143

TKR5113

TKR1325

M3x14mm Flat Head Screw

TKR5144

TKR5145B

TKRBB08165

Ball Bearing(8x16x5mm)

TKR5144

Differential 0-rings

TKR5145B

Differential Shims (6x17mm)

TKR1325 x4

TKRBB08165

Diff

Oil

TKR5614X

TKR5150

TKR5144

Grease

Step

B-2

Step

B-1

Step

B-4

Step

B-3

TKR1525

TKR5012

TKR5581

TKR5575X

TKR5152

Front

Rear

Note: The front and rear

bulkheads are dierent.

The front has a much

greater output angle

compared to the rear.

TKR1222

TKR1603

TKRBB05114

TKR1226

TKR1222

TKR1525

13x16x0.1mm Diff shim

TKR1222

TKR1226

TKRBB05114

TKR1525

M3x14mm Cap Head Screw

TKR1603

M5x4mm Set Screw

TKRBB05114

Ball Bearing (5x11x4)

TKR1226

5x7x0.2mm shim

TKR1603

Grease

Note: at spot

*may not be needed

Note: at spot

*TKR5581C

(Option)

Bag C

Front Gearbox

(overview)

Thread

Lock

Step

C-1

Step

C-2

Step

C-3

Note: TKR1222 and TKR1226 Shims - The gear mesh should be tight without any binding. TKR1226 should

always be installed. Then test tment of the di with both TKR1222 shims on the gear-side of the di. If the di

turns freely without binding, continue to next step. If the di binds and does not turn freely (it will make a

grinding or crunching sound when spun), remove one TKR1222 shim from the gear side and install it onto the

other side of the di. Reassemble and test the mesh again. If it is still binding, remove the second TKR1222 shim

from the gear side and install it onto the other side of the di. When you are satised that you have the best

gear mesh possible continue to the next step. You may end up using only one shim on the gear side.

TKR5575X

TKR5016B

TKR5152

TKR5016B

TKR5584

TKR1222

TKR1525

TKR1529

TKR1222

TKR1529

TKR5181

TKR1525

TKR1222

TKR1525

TKR1226

TKRBB05134

TKR1525

M3x14mm Cap Head Screw

TKR1603

M5x4mm Set Screw

TKR1222

13x16x0.1mm Diff Shim

TKR1226

5x7x0.2mm Shim

TKR1603

TKRBB05134

TKR1226

TKRBB05134

TKR1603

TKR1525TKR1525

Grease

Front

Rear

Note: at spot

*TKR5584C

(Option)

Note: The front and rear

bulkheads are dierent.

The front has a much

greater output angle

compared to the rear.

*may not be needed

TKR1529

M3x20mm Cap Head Screw

Bag D

Rear Gearbox

(overview)

Thread

Lock

Step

D-1

Step

D-2

Step

D-3

Note: TKR1222 and TKR1226 Shims - The gear mesh should be tight without any binding. TKR1226 should

always be installed. Then test tment of the di with both TKR1222 shims on the gear-side of the di. If the di

turns freely without binding, continue to next step. If the di binds and does not turn freely (it will make a

grinding or crunching sound when spun), remove one TKR1222 shim from the gear side and install it onto the

other side of the di. Reassemble and test the mesh again. If it is still binding, remove the second TKR1222 shim

from the gear side and install it onto the other side of the di. When you are satised that you have the best

gear mesh possible continue to the next step. You may end up using only one shim on the gear side.

TKRBB05134

Ball Bearing (5x13x4)

TKR1529

TKR1201

TKR1221

TKR1201

TKR1529

M3x20mm Cap Head Screw

TKR1524

M3x12mm Cap Head Screw

TKR1201

M3 Lock Nut Black

TKR1221

M3x8mm Washer

Step

E-1

Step

E-2

TKR1524

TKR5181

Bag E

Low Profile Wing Mount

SETTINGS

1 2

3 4

1 2

3 4

POSITION SETTINGS

1 - REARWARD LOW 2 - FOREWARD LOW

3 - REARWARD HIGH 4 - FOREWARD HIGH

DOWNFORCE SETTINGS

(downforce angles)

Note: Stock position setting is

# 3, Rearward High

Note: Stock downforce setting is 4

Stock Position

(”D” Block)

Stock Position

(”C” Block)

30.2

TKR1601

TKR5086

TKR5491 - 2.4mm

TKR5086

Install the Sway Bar Ball onto the

Sway Bar Wire until the end of

the wire is ush with the ball as

picture above.

Note: Loosen the M3x4 set screw (TKR1601)

the anti-roll bar does not

turn freely.

Note: Do not over-tighten

TKR5049A

TKR5730

TKR5165

TKR5515

TKR5174

TKR1402

TKR1601

TKR5079A

TKR1522

M3x8mm Cap Head Screw

Bag E

Rear End

*TKR5490 - 2.3mm

*TKR5492 - 2.5mm

*TKR5493 - 2.6mm

*TKR5494 - 2.8mm

*TKR5495 - 3.0mm

(Option)

*TKR5163

(Option)

*TKR5164

Thread

Lock

Thread

Lock

TKR1327

TKR1333

M3x40mm Flat Head Screw

TKR1238

M4x10mm Droop Screw

TKR5049A

Pivot Ball Sway Bar

TKR5079A

Stabilizer Ball

TKR1528

M3x18mm Cap Head Screw

TKR1327

M3x16mm Flat Head Screw

TKR1333TKR1333

TKR1238

TKR1528

TKR1601

M3x4mm Set Screw

Step

F-1

Step

F-2

Step

F-3

TKR5020

TKR1402

M3x8mm Button Head Screw

TKR5165

Note: With these stock settings,

Anti-Squat is: 1° / Rear Toe is: 2°

For reference: With center dot

inserts in both braces,

Anti-Squat = 3° / Rear Toe = 3°

Use a #19 drill bit or

4mm reamer to ream

arms until hinge pin

falls through freely.

TKR5572

TKR6856

TKR5580

TKR6856

TKR5534

TKR5021TKR5021TKR5021

TKR1201

TKR6856

CV Joint Pin

TKR1602

M4x4mm Set Screw

TKR1201

M3 Locknut Black

Grease

Step

G-1

Step

G-2

Changes to the wheelbase have a dramatic eect on handling,

since it shifts the disribution of weight over the rear wheels.

This adjusts traction. By shortening the wheelbase at the rear, you

are placing more weight over the rear wheels.

Changes to the wheelbase also change the amount of sweep the

rear driveshaft will have. More driveshaft sweep creates an eect

similar to anti-squat, where the rear end gets pushed upwards on

throttle. This helps reduce chassis slap landing jumps on throttle.

(FRONT)

(REAR)

TKRBB10154

Ball Bearing (10x15x4)

TKRBB06135

Ball Bearing (6x13x5)

Bag G

Rear Hub/CVA Assembly

Thread

Lock

Note: notch on pin

needs to line up

with set screw.

TKR5545

TKRBB10154

TKRBB06135

TKR5570-17

TKR1602

TKR5188

TKR5123

TKR5188

TKR5052A

This side mounts on hub

Note: angled link

This side mounts on shock tower

Note: straight link

TKR5053A

25.50

Note: Notch always goes

left side of vehicle

Stock position is 6/B

TKR1529

TKR1201

Right

TKR5053A

This side mounts on hub

Note: angled link

This side mounts on shock tower

Note: straight link

TKR5188

Left

TKR1529

TKR5123

TKR1201

M3 Locknut Black

TKR1529

M3x20mm Cap Head Screw

TKR5053A

Pivot Ball M3x6.8mm

No Flange

TKR5052A

Pivot Ball M3x6.8mm

TKR5188

TKR5052A

Step

G-3

Step

G-4

Bag G

Rear Camber Links

Tabla de contenidos

Otros manuales de Coche de juguete motorizado de Tekno RC

Tekno RC

Tekno RC ET410 Manual de instrucciones

Tekno RC

Tekno RC EB48.3 Manual de instrucciones

Tekno RC

Tekno RC EB48.2 Manual de usuario

Tekno RC

Tekno RC EB48.4 Manual de instrucciones

Tekno RC

Tekno RC EB48.3 Manual de instrucciones

Tekno RC

Tekno RC ET48.3 Manual de instrucciones

Tekno RC

Tekno RC ET410.2 Manual de instrucciones

Tekno RC

Tekno RC NB48 2.0 Manual de instrucciones

Tekno RC

Tekno RC ET48.3 Manual de instrucciones

Tekno RC

Tekno RC NB48 2.1 Manual de instrucciones

Tekno RC

Tekno RC EB48 Manual de usuario

Tekno RC

Tekno RC NT48.3 Manual de instrucciones

Tekno RC

Tekno RC SCT 410 2.0 Manual de instrucciones

Tekno RC

Tekno RC SCT410 X Manual de operación y mantenimiento

Tekno RC

Tekno RC SCT410SL Manual de instrucciones

Tekno RC

Tekno RC NB48.4 Manual de instrucciones

Tekno RC

Tekno RC EB48 2.0 Manual de instrucciones

Tekno RC

Tekno RC NB-48 Manual de usuario

Manuales populares de Coche de juguete motorizado de otras marcas

Eduard

Eduard Humber Scout Car Mk.I exterior Manual de usuario

Traxxas

Traxxas 4995X Manual de usuario

Jamara

Jamara VW T1 Bus Manual de usuario

REVELL

REVELL 68 CHEVY CHEVELLE SS 396 Manual de usuario

Schumacher

Schumacher Pro Cat Manual de usuario

Tamiya

Tamiya TT-01 TYPE E Manual de usuario

Eduard

Eduard Krupp Protze 6x4 1/48 Manual de usuario

New Bright

New Bright 61072UEP Manual de usuario

Team Durango

Team Durango DEX410v5 Manual de usuario

Jamara

Jamara Mercedes Actros Muldenkipper 2,4 GHz Manual de usuario

PLAYMOBIL

PLAYMOBIL 9536 Manual de usuario

Atomic

Atomic BZ3 Manual de usuario

Aiyaplay

Aiyaplay 370-290V00 Manual de usuario

Power Wheels

Power Wheels GRJ53 Manual de usuario

ZEROTRIBE

ZEROTRIBE Zetricks ZT1144 Manual de usuario

INJUSA

INJUSA 412 Manual de usuario

Maverick

Maverick MSC-30BR-WP Manual de usuario

Land of B.

Land of B. Rollin' Riders Manual de usuario